I have a 2000 Toyota Avalon XLS with 134k miles, engine is a v6 (3.0). It has a rough idle and a steady misfire. You can drive it sometimes and it will run perfect and you can drive it sometimes and it will misfire. I am getting codes P1150, P0300,P0302, P0304,P0306. Driving me nuts.
View 1 RepliesI recently bought a 00 Excursion v10 2wd everything looked right no major problems. I noticed it has a rough idle and i thought it could be the EGR i went under the hood and there's no EGR in sight. I plugged the OBD reader to see if it would give any codes since the there was no check engine light on and wanted wanted to make sure it worked, It showed a P0304 code its Cyl4 misfire i checked plugs/coils and i noticed there's a little insert inside Cyl4 plugs hole in the head that it has the plug screwed on. I decided to change all the plugs and the coils and i still have the rough idle and code i can hear a ticking noise around the engine in the passenger side.
View 7 RepliesCheck engine light came on. Codes are P0300, P0302, P0304. Plugs were previously changed. Plugs look good. Changed both coils. Light still one. Injectors also previously cleaned. What else should we check for? Valves hanging? Anything else to check for?
View 5 Replies2000 Ford Ex 5.4 V8 175K miles
Top of radiator (plastic part) had a small crack and started leaking on drivers side. Fixed with JB Weld. Ran fine for a day. Now I have a bad misfire and codes P0301 and P0302 (Cyl 1 and 2). Cleaned MAF and checked Air Filter. All good. Plugs replaced at dealer less than 20K miles ago.
So I took off Cyl 5 (easiest) and found that the boot is fine but the collar on the boot is done for. Can this cause the issue?
04 trailblazer, 4.2. Running rough and SES light on. Had codes pulled and showed p0340 (CMP sensor circuit malfunction) and p0300 (Multiple engine misfire detected). Replaced the CMP sensor and left negative battery cable unhooked for 20 minutes or so to clear the codes. Upon start up no more SES light and idle was slightly better. Within seconds it SES was back and it is again running poorly. Cruise control is no longer functional as well.
View 7 RepliesMy girlfriends 2007 accent as thrown codes p0300 and p0302.
After reading everything I could find, I had coil pack on my list of possible problem items.
The car sat in the driveway yesterday and when she went to start it today, she couldn't get it to.
I got it to start when I got home by giving it some gas while turning the key, but I don't want to drive it anywhere.
The hard start is leading me to believe it's the coil pack.
I was going to start with changing the pcv, spark plugs, and run fuel injector cleaner through it because those are the cheap possibilities...but now may add in a new coil pack.
The car doesn't seem to run that rough.
Replaced coil pack and spark plug wires with parts from O'reilly auto
16684 - Random/multiple cylinder misfire detected
P0300 - 35 -10 - Intermittent
16686 - Cylinder 2
P0302 - 35 - 10 - misfire detected - intermittent
16687 - Cylinder 3
P0303 - 35 - 10 - misfire detected - intermittent
I have searched and browsed multiple websites and threads to no avail. They all seem to be dead ends.
'02 TB w/ code P0300 / Random misfire. Started the other day when it was very damp out, FWIW. Feels like ur driving on rumble strips during acceleration. Rough idle also. It does not do this continually though as after a while (minute) it clears up and runs smooth for a while then runs rough & light will again for a while. I seafoamed it today since it been about 60k since last seafoam. I thought that might have worked until I drove about 20 mile and it went rough again. I also cleaned the oil out of the cam sensor elect connector, since that caused rough running before, although it didn't throw that code. It seems to be very intermittent. '02 TB, 185k miles, orig plugs changed at 125k. Is it actually just going in & out of a limp-mode? O2 since it's random ???
View 14 Replies05 2 wheel drive f150xl 4.2 l 135,000 miles. Smoking white out of exhaust. More at start up but doesn't go away. Turns a little blue. When parked at idle if I bring up the RPM's quick I will get a little puff of black in the white smoke. I can't smell or taste(when I touch my fingers to mouth) any anti freeze in the exhaust smoke but I live in Myrtle Beach and I have little if any anti freeze in the coolant. I flushed the motor, changed oil and filter and added a can of seafoam. I took the throttle body off and cleaned it. I also replaced the air filter because I went down a dirt road and hit a deep water hole. Dirt and mud got into the air filter and by passed it also. This was the reason for the engine flush also. I can't recall any smoke before this. Maybe a puff on start up from moisture not sure. Im going to buy a coil pack and plugs and start from there. I have never had this many codes.
P0174 Bank system 2 to lean P0300 random multipl Lean mil. Missfire detected P0305 random multiple Missfire detected cylinder 5 misfire P0306 cylinder 6 Missfire P0316 Missfire detected on start up first 1000 revolution
i have a 01 passat with a v6 in it on 4 motion and im having an issue with soem mis-firing
i pulled the codes. P0300 P0301 P0302 and P0303 which are all saying that there are missfires in cylander 1,2 and 3 and random miss fires.
im also getting a P0340 which is cam sensor A or the right hand bank. problem is i just replaced the cam sensor and when the motor got warm, the code came back. I was told by the previous owner that the car needed a Coolant Temp Sensor....can this be the cause of my mis-fire issue? hear me out.... it only happens when the car is warm so im thinking that the car is warm but the ecu thinks its cold cause its not getting a good signal from the CTS. thus its either advancing the timing as if the motor is cold and cuasing a miss fire or something along those lines. any thoughts?
2005 4cyl. Vue with 54K... Steady CEL. Runs great. Absolutely no problem accelerating. Don?t hear or feel any misfiring. There is a slight rumbling sound when I first start to drive the car, but to me, the sound doesn't seem come from the engine, but rather underneath the car. It goes away when I continue to drive. Since winter began, I occasionally feel a very slight hesitation during idle?happened once or twice lately.
Again, I only feel justified in mentioning it simply because of the codes that were generated. None of my passengers have made a comment about the idle or the drive. My friend, however, made a remark that occasionally, there is a very very very slight hesitation at the downshift when braking. No crack in gas cap. Great fuel economy. No problems accelerating at all. Never hear or an actual misfire, which I take it, means a problem when accelerating, a jerking, or popping noise.
Took it to a dealer. Codes were 0300, 301, 302, 303, 304?302 generating most often. Dealer recommended new ignition module and plug replacement, but they said it wouldn?t be a guaranteed fix and that it may need EGR replacement (don?t hear knocking though) or be a burnt valve in the cylinder. No suction out tailpipe, no rotten egg smell (signs of burnt valve). What are the chances of burnt valve in a car with 54K anyway?
Also, my maintenance schedule claims that I don?t need new spark plugs until 100K. Is there anything else this could be such as a dirty injector system, fuel filter, fuel pump, or air filter? Again, overall, the car runs GREAT! Should I just wait and see if the misfire becomes more pronounced so when I take it to a mechanic, they won't be looking for a needle in a haystack?
I have a 2000 Suburban 4wd that has a p0300 code. The misfires are coming mainly from #2 and #7 cylinders. Misfires only occur at idle. over 1500 rpm the misfires disappear. I have put new A/C Iridium plugs in, new wires, and new coil packs on both cylinders but the problem is not any better. All 8 fuel injectors all go to 55 psi when activated and drop to 28 when released. All tests were done with my Snap-On Solus.
View 2 RepliesI would like to find out why my car is misfiring before throwing parts at it. I have a basic level of mechanics and have checked a few things before posting here, which may or may not have ruled out some possibilities.
The problem: I have been consistently getting P0301 and P0304 but only happens sometimes, while other times there is no check engine light. I first checked the ignition coil, right side of it, that controls cylinders 1 and 4. Did resistance test, measured for voltage, and checked the wires for continuity to the connector, with everything coming out good. I know a few must have had issues with the cheap pigtail connector like me so I went and changed that but still got the misfire codes. I then put in an older known to be good working coil but no change.
After that, I removed spark plugs 1 and 4 and put them where 2 and 3 go but still got the same codes P0301 and P0304.
A friend who is a mechanic for Nissan checked the spark and wires, saying they were fine. He then checked the injectors and noticed that injector 1 didn't increase in ticking sound when RPM increased. He said I should replace injectors 1 and 4 to see if that changes anything or switch injectors 1 and 4 with 2 and 3 to see if the codes at least change. I removed them all, got two of them from junkyard just in case, made my own tool where I pumped straight fuel injector cleaner through each of them with pumped air, and put the two from junkyard on cylinders 1 and 4. I still got the same codes so then I switched injectors 1 and 4 with 2 and 3, which didn't change the codes.
I was told by another local mechanic shop that it's definitely the coil but I knew it wasn't.
Other info: I am not sure it would matter when dealing with a misfire but I borrowed a code scanner and saw that the Long Term Fuel Trim was -7%. I researched that and it means that the car is running rich and the computer is being told that it needs to run lean. I am not sure that this would make only two of the cylinders misfire and the freeze data shows that same negative LTFT for when the P0301 happened. I also know that there is an air leak at the gasket where the front cat connects to the flex pipe/rear cat. I have also gotten a rear downstream 02 sensor code once within the past month but it hasn't come back.
Would the LTFT being lean have anything to do with the misfires? Would the gasket between the two cats cause the 02 sensor to get a faulty reading? If so, would the downstream 02 sensor be able to adjust to a lean fuel mix? What else should I check?
OK - so is my engine computer toast? The other day on the highway on the way home from work, my check engine light started to flash, and the car on cruise decelerated from 80MPH (ok I was speeding) to 70, and flooring it didn't make is speed up, and that's when i noticed it was shaking a little, so i pull off the highway and it's as if a spark plug was pulled.
So I made it to a parts store to have the code read, then started it back up, all was well. As if nothing ever happened. So I dismissed it as a pocket of water in the fuel or some other oddity.
2 days ago it happened again on the highway. So I pulled into the shoulder, shut off the car, and started it again. Runs fine. Engine computer?
The engine on my camry 2007 was overheated and I had the headgasket replaced but now it has misfire codes and rough idle this is a 2.4 engine I replaced 2 of the coils but still it has a rough idle... when the car is running it runs pretty good.
View 5 RepliesThis has been an ongoing issue with our 2006. We purchased the car about a year ago and have put on just over 8,000 miles. Rebuilt the battery pack and replaced the 12v battery. This is my wife's car and I have a 2005, so I have done some diagnostics, tuneup, and even swapped some parts between the two cars trying to narrow down the issues.
Only recently have codes been recorded. The car is has a noticeable misfire at low RPM. Here is what has happened up until now:
11/29/15 - replaced spark plugs - #1 was fouled so I swapped coils between cylinders 1 and 4
2/25/16 - replaced 12v battery with new battery
4/1/16 - P0300, P0301 codes were first recorded and reset to see if they came back
4/10/16 - swapped Integration Relay with my 2005 (part # 82641-47010). My 2005 ran poorly after the swap, so I put a used one in my 2005.
I recently had detected always misfire on those cylinders. Any relation between them?
View 1 RepliesI've got a troublesome misfire in a 2007 Sonata V6, 70k miles, which I have been trying and failing to track down for a long time.
More than a year ago, the owner of the car complained of rough idle. When this was first mentioned, I looked at the car, she and I talked, and I concluded that she hadn't changed the oil in some 20k miles. ...... Nothing else seemed wrong. I changed the oil, thinking that what she needed was an oil change.
Some time later, I was in the car myself and all of a sudden felt a strong bucking. Must've been a misfire. I recommended taking it to the Hyundai dealer, thinking the so-called 100k mile powertrain warranty would cover whatever it was (it didn't but whatever).
We drove it to the dealer. The dealer firstly informed us that the CEL had burned out, so we had missed some codes. The dealer further us the car needed new plugs and replacement of both upstream O2 sensors. Here was what the mechanic wrote:
"BETWEEN 35-40 PUT CRUISE ON AND WILL FEEL. CHECK AND ADVISE COMES AND GOES. MULTIPLE CODES STORED IN SYSTEM. ... P0300 RANDOM MISFIRE (ACTIVE), P0140 O2 SENSOR CIRCUIT NO ACTIVITY, P0154 O2 BS S1 NO ACTIVITY. WATCHED O2 VALUES AND FOUND ERRATIC READINGS. FOUND TSB 10-FL-012 SUGGESTING REPLACEMENT OF BOTH UPSTREAM O2 SENSORS. RECOMMEND COMPLETE SYSTEM TUNE UP FOR RANDOM MISFIRE. HOWEVER MISFIRE COULD BE RELATED TO O2 ACTIVITY.
So the owner went to a different mechanic and had the plugs, upstream O2 sensors, and one of the downstream sensors replaced. All OEM, I believe. ($$$!) (O2 sensor parts 39210-3C100, -3C200, and -3C400) Dunno why the downstream one was replaced, not my doing.
Following this, there was no real improvement. No codes either. The problem comes and goes, so maybe I thought it was fixed, but it has come back. Sometimes, it can be felt just slightly when the car starts cold. Other times, it can be felt just barely when driving at a consistent speed. Sometimes, the problem becomes really bad and jerks the car around. Other times, nothing.
What to check next? Coil packs? Intake manifold gasket? She never gets "top tier gasoline," but I would be skeptical that that's the problem. These are the top three suggestions I've heard.
So, my 2003 F150 4.6 that I just put back on the road after a four month break is running like crap. I took it off the road for the winter because it was missing (no codes) and didn't feel like dealing with it then but after running it for a day the CEL comes on. It shows the following:
P0304 - hoping it is a coil pack
P0456 - pending. Gas cap?
P0171 - pending. One bank too lean?
Does the 171 code possibly have to do with the misfire in Cylinder 4? I know it is impossible to tell yet but am hoping there is a potential connection.
Before I parked it in January, it was running a bit rough and stumbled on acceleration but never would show a code. Now all this. Going to change the coil first, tighten the gas cap, check for leaks and see what happens but is there anything common on these trucks that I should also be looking at?
So i got two codes.... P0300 and P0305. I am thinking its the coilpacks because i changed the spark plugs a few months ago. Cleared it last week and came back today. What else could it be? And is it ok to just change one coil pack or do i have to do all of them? The recall was done in 2007.
View 3 RepliesMy 97 F150 4.6 4x4 threw a P0302 and P0401 the other day, I traced the miss fire to a loose injector plug. I reset the codes last weekend, I got in the truck and went to the Dump and to town to pick some stuff up. It threw the EGR code again, so this morning I did a little checking on the EGR I cranked the truck and disconnected the FPR vacuum line and hooked it to the EGR valve and the truck died down but didn't completely die.
Now the green line that went to the EGR valve felt like it had a slight bit of pressure coming from it. Is this normal? I did pull the white feed line from the EGR Regulator and it had good vacuum.
The regulator also makes a humming sound when you cut the truck off. Ill be pulling the alternator this weekend due to it going out last night, while I'm in there if Ive got to pull the throttle body id rather do it while I'm elbow deep in it. So does it sound more like a Clogged Throttle body or a Faulty sensor?