Accent LC (2000-05) :: Light Grinding Noise When Let The Clutch Out / Pedal Super Hard
May 1, 2013
Yesterday I was driving home and my clutch started acting up. To start I was unable to press the pedal. The pedal was super hard, then let up but didn't feel right.
I removed the slave and the pedal went down fine. Both the master and the slave have no leaking and fluid levels are good. I haven't been able to have a buddy look at the levels when I press the clutch, but....
Here is a little more, the car shifts fine with the car off, it goes into all the gears, but with the car on it will not shift into gear. Also there is a light grinding noise when I let the clutch out..
I ordered a clutch kit already, but don't want to pull the trans if I don't have to, I would love to hear the issue is with the master or slave.....
2005 Hyundai accent with 138,000 miles
View 4 Replies
Advertisement
2000 Ford F250 crew cab 4 x 4 with 7.3. 6 speed transmission.
I just had a new clutch installed and now I am have a grinding noise when putting it into 1st gear and when I change from granny to first it will grind also. I did not have this issue before having the clutch replaced.
I have also just had a new hydraulic clutch kit installed.
View 5 Replies
2001 1.5 Accent. It has not been starting consistently for the last few weeks. Ive had to use the jump box on it a few times and that worked.
The other day (cold day!) it died at the stoplight after driving for about 20 mins. It made a grinding crunch sound from under the hood as it died. After several attempts on jump box it fired up and ran again for about 15 seconds and died and made sound again.
This repeated itself a few times before I got it towed home.
I removed alternator and it tested good (PASS) at two parts stores...testing 3 times each.
Battery has about 14 volts at the posts without having charged it after event.
What would cause the car to die and make the awful sound? And why would it appear to need a jump start?
I was thinking alternator but.....
View 12 Replies
First off my trucks a 2000 v10 f250 with four-wheel drive and 2 wheel abs with about 230000 miles on it.
I Recently replaced my unit bearing on my drivers side because I thought it was the cause of a grinding that only happens on hard left turns but I wasnt the cause it was going bad causing play in the half shaft. I didnt seem to notice and wear on the shaft from bad needle bearings but I have to take it all apart again to be sure. Was just wondering what else could be the cause of this noise. I plan to pull the axel shaft and change all the seals.
View 3 Replies
I have an 00 Accent 1.5 liter 5 speed with about 192000 miles on it. I have put about a tank of gas through it since I've owned it, so I can't give a lot of background on it. When I got it the previous owner told me it was popping out of fifth gear and the clutch fluid leaked.
Upon driving it around a while I noticed it would pop out of fifth and third gears almost at random, but seemed to happen more when I applied throttle. I assumed it was an issue with the shifter not fully engaging the gears, and checked out the bushings under the hood and in the console. All looked good, and I didn't see any extra play.
I drove the car for about 30 miles straight and had to downshift and wasn't able to get the car to go into any gear but fifth. I was moving about 20 mph when this occurred. I was able to limp along to a parking lot where I let the car sit for about ten min and I shifted through the gears when stopped. I headed back home with this problem throughout the trip. There is a sound that happens on occasion (that stops when I press the clutch pedal) that sounds like a bad bearing in the clutch area.
When I'm stopped with the car in neutral and I release the clutch the car stalls like it's in gear. I was able to get the car to move some, but it really doesn't want to it acts like there is something jammed in the gears and popped really loud when I backed it up.
There is fluid for the master cylinder, and I can see the slave cylinder moving when the pedal is pressed. I jacked it up and removed the plug to check for gear oil, and it came pouring out, so I think it has fluid in the gearbox. I'm pretty sure it needs a clutch at the least. I think there may be some internal damage in the tranny, and I'm only into the car for the time it took to power wash a house and don't want to get involved in a big mess.
View 5 Replies
2001 Accent 1.5 GL 165K miles.
The clutch doesn't engage until it's on the floor. I have to push real hard to allow the gear to engage. It then shifts... sometimes smoothly, sometimes it takes a hard push of the gear shifter, or it grinds until getting into gear.
I've changed the master cylinder twice in about 3 years but those times the pedal had no spring and just fell to the floor and stayed. Now, the pedal has spring (I push it to the floor and it springs back) so I assume the MC is ok. I even bled it with fresh fluid.
I'm not sure if the tranny fluid has ever been changed. Would changing the fluid fix this problem or does it sound like I need a new clutch? I'm guessing it needs a new clutch (or corresponding parts) since I've had two MC's go bad in a few years.
The pedal, even when it's shifting smoothly is pretty non-responsive and still engages a little mushy (comparing it to my 2012 Elantra 6sp).
View 4 Replies
I'm at my place in Florida 1,000 miles from home, and when I started the car in a mall parking lot, there was some grinding metallic noise for a few seconds and I couldn't get it into first or reverse and the clutch pedal was way down. I was able to get going in 2nd and eventually the clutch was back to normal and I could get 1st and R. What happened? Broke some fingers in the pressure plate? Seems to run fine now but have a 1,000 mile ride ahead in the morning.
View 1 Replies
I'm not very mechanical when it comes to cars. I have never had any clutch issue with my car. I arrived to work yesterday fine. When I started to leave it was incredibly hard to get into reverse and I had to force shifting after I left and the clutch had also lost all resistance and I could easily push it all the way to the ground. What could be a cause of the clutch always working perfect including the last time you drove it, and then 8 hours later you start up and it has done a 180. The fluid level is fine. I would presume if my clutch had went I have have slowly noticed it going.
View 1 Replies
Occasionally the car will make load grinding noise that sounds like a garbage disposal:
[URL] ....
[URL] ....
When this happens the gas pedal is also vibrating. It will go away when the car is stopped and may not return for a few days.
It's 2008 accent SE with a performance chip.
View 14 Replies
On releasing the clutch pedal, a creaking noise can be heard, which:
- sounds and feels like a rusty spring being unloaded
- occurs for the entire range of pedal travel, but worse near the bottom
- is louder outside the car than inside
- happens not only when driving, but also when stationary with the engine off
I don't think anything is wrong with the clutch itself, or any bearings, or major components... It just feels like something needs to be lubed. I've lubed the spring above the pedal inside the car, with no real effect.
View 4 Replies
2000 GTI
260,000 miles (60% highway)
2.0L 4cylinder AEG
All stock.
I have a new issue developing on the clutch of my car. When I fully press the clutch pedal to change gear, I hear cacophony of grinding, hissing and whirring noise, probably coming from gearbox. When I take my foot off of the clutch pedal completely, the noise is gone. half clutch has reduced amount of these noises. I had this symptom briefly one night two weeks ago and when I topped up oil, this was gone. Tonight, it is back.
View 10 Replies
So I have a 2000 Hyundai Accent, 1.5L with an automatic transmission. I'm hearing a grinding noise when I'm driving. It gets faster as the car goes faster, but the engine RPM has no effect only the speed of the car.
I got new tires, changed the CV axle shaft on both sides, and I also changed the front struts as I was told that one of the struts was bad the last time I took the car for an alignment. None of that has had any effect on the grinding noise.
Then I jacked the car up on both sides and let the wheels spin, and the grinding noise is present that way as well. Then I jacked up just one side at a time. When the driver's side wheel is spinning, the noise is audible, but not when just the passenger side is spinning.
I then disconnected the brake caliper from the driver's side and held it up with a tie wrap to keep it out of the way. The noise is still audible when the wheel is spinning, so it's not the pads or a clip or anything like that.
So now I'm down to a couple of ideas.
1) Wheel bearings
2) Something is hosed in the differential or transmission. I'm guessing that the differential is more likely, as the transmission should effect both sides the same, right?
I'm going to check the wheel bearings now, though to me it seems unlikely to be the problem.
View 10 Replies
I've got a 2000 F250, 5.4L 4x4 with the ZF5 5-speed transmission. Three years ago I replaced the complete clutch assembly, pressure plate, throw-out bearing, etc, and had the flywheel re-machined. Put it back in and all has been well. Only has about 15k miles on it. Earlier this week I went to drive it and all of the sudden it started getting harder to shift and by the end of the trip the clutch will not disengage at all when I push the pedal in.
Furthermore the pedal is much harder to push than it always has been. Checked the reservoir and it's fine. After some searching it seems to most likely be an issue with the master and/or slave cylinder either needing to be bled or replaced. Further reading revealed that bleeding and recommends just replacing the whole system, so I've priced that out. Was it a master/slave issue? Anything else I should check in case it isn't?
View 2 Replies
So I have a 2000 Hyundai Accent that has been a relatively good car for the 11 years I've owened it. About 2 months ago I got a flat tire, which I didn't notice until a passenger in another car told this while waiting at a stop light. I was so close to home (within a mile) that i decided to trek it slowly back. Made it back and a friend of mine put a donut on and I had the two front tires replaced the next day.
Within a week of having the tire changed I noticed several issues with the car. First, it was starting to make a very loud, almost grinding sound. Looked into whether or not tires had anything to do with it since I just had them changed. I pretty much now think its a wheel bearing. It seems to be coming from the right front passenger side. It gets louder as I speed up and also especially loud during left curves and turns.
But all that is background for my real problem. In addition to the above the transmission started acting up. At first I though it was the engine because the problem was initially just sputtering whenever I would slow the car down to a stop. I changed the spark plugs and wires but that didn't work. Then it started having problems shifting. Even going to 3rd now it can take a while, staying at a higher than normal rpm. And when it finally shifts it knocks hard. Only thing I did was have the transmission oil changed since it was about 40k miles past where Hyundai says it should have been done. That worked only slightly (maybe not at all). On top of that, there's also has an engine smell (like hot burnt oil) inside the car when I drive it for an extended amount of time. This was happening before and after the transmission oil change.
These are the first major issues I've had with this car. The only exception is that I've had a failed oxygen sensor twice but that was cheap to have repaired and both times the check engine light was on. It has not turned on once since this started happening. I've stopped driving the car long distances and especially over hills. I go 5 miles between home and work with it now. I was starting to think about getting another car before this happened but I'm still not ready to do that now.
View 1 Replies
Noise sounds like its coming from driver's side. It's not terrible until you hit 30-40km/h, after that its quite loud. No whistling sounds, which i was told to listen for if it were a wheel bearing (although I ma not convinced is the only sound a warn bearing makes).
The sound sometimes goes away when I am on a bend turning left (taking the weight off the drivers side wheel).
View 6 Replies
So I had all of my belts changed including timing belt and tensioner pulley as well as an oil change. After, I noticed a weird pulsating grinding/wining noise coming from the engine bay. It only can be heard once the car is warmed up. (It is much louder in real life.).
Car Noise - YouTube
View 1 Replies
Recently I've noticed more that when we first start the hyundai in the morning or after sitting a while and we use the brakes it grinds/ squeals a little and then doesn't after about 2 or 3 miles. Is this something to get checked out or should I spray something on my brakes to lubricate?
My next step that I though of was to get a simple automatic car wash cause it's been a bad winter in Rhode Island and the street shave been flooded with rock salt. I figure that might cause some friction under the pads.
View 1 Replies
My daughter has bought a 2003 4 door accent and on the way to work she lost most of the brakes. I could not see any fluid leaking and the level was ok. I did try pushing on the brake pedal with my hand and it was making a noise like a clicking? I was thinking it was just the brake light switch but not sure. The place she bought it from put new brakes on it when the driver side was getting really hot. I am thinking maybe air in the system? It sounded like a caliper was sticking when I test drove it but only a couple of times. You would have some brakes but you had to pump the peddle.It is in a parking lot right now but I can work on it unless it is some sort of different? I am going to try to bleed it in a little bit but was thinking I should ask around. I read that the piston could be sticking but can you just rebuild the master cylinder to fix it if that is what it is? I could pull the pedal back a little bit. I only looked at for 4 or 5 minutes kinda dark and no tools with me.
View 10 Replies
I own a 2005 Hyundai Accent 1.3 SOHC and a while ago the front right wheel started to make a grinding noise, problem was related to the brake system..
So far I've tried replacing the rotor (disc), repaired the caliper (using a rebuild kit), replaced hoses (both), and event the master cylinder.... and the problem persists, it actually came to the point that after driving a while the front wheels will get stuck.
I've followed all the directions from the service manual and it still got the problem...
View 14 Replies
I have a grinding/Rattling noise coming out of the front area of the transmission when the clutch is disengaged (up), noise stops when clutch is pushed in. 99 (6/98) F-350 7.3, manual, 4x4, 192xxx mi. Just came out of the shop with the following done to it:
New Power Force clutch kit, twice.
Transmission Rebuilt twice.
Different rebuilt transmission.
Rear main seal r/r.
After first time in shop the noise was apparent. about 3,000 miles were driven with no change, brought back to shop, where transmission was gone through again as well as a new clutch set, same noise still present! Another transmission was rebuilt and installed, same noise!!!
View 11 Replies
The vehicle is a 2000 Excursion 7.3 Diesel. I have never owned a diesel before....
First issue is that I have developed a hard start. It started last Saturday, and went from sporadically starting hard, to starting hard every time. I have 146,000 miles on her. She cranks strong, but will not turn over the first time, sometimes takes 2, 3, or 4 times. (Foot on gas pedal) I don't know if it's an issue of not getting enough fuel or what. Occasionally, even after she starts, it's very rough (shaking the whole vehicle, and acting like she wants to die) until I rev the engine and she smoothes out. After she smoothes out, there is no problem with wanting to drive, she's strong. If I kill the ignition, and start up immediately, she starts the first time, it's only after 10 minutes or so of being off.
My next issue is a clunking noise when I press the gas pedal. I don't know if it's the tranny, because she shifts pretty smooth for the most part, doesn't miss gears, etc. I could be travelling say 50MPH, press the gas pedal very little, and I can hear the clunking, and actually feel it every time I press it. (Don't have to be mashing the pedal, happens on very light presses as well).
I have the TS Performance 6 position chip, otherwise she's stock. I tow roughly a 7000 travel trailer every couple of weeks, never any problems before this.
View 14 Replies
