MY gc started cutting out a few weeks ago while idling in gear. I changed out the four plugs I could get the wires off. It's a v6. It started running better for a couple of days. I need to know of any way to get the stuck boot off. I also have a feeling there is something else wrong. Anything else that might be causing it to cut out. It has progressed to cutting out while going down the highway.
View 4 RepliesI have a 99' GC and just changed out the EGR valve. Now the engine cuts out when you brake or get to a low speed. Idles a little rough also.
View 7 RepliesI have a 99 voyager that has started making a whirring sound this last week. The water pump, serpentine belt, tensioner have all been replace several months ago. The battery light came on for about a minute and then went off the last night. I checked the voltage with the engine running and it measured 12.5, the same as when it is off. When I revved it up the voltage went up to 14.4 volts. Is this normal? What could be making the whirring sound?
View 2 Replies2007 town & country with 93k when car is started (cold) after setting to completely cold have a whirring noise that goes away after car is completely warmed up thought was alternator but noise doesn't seem to be coming from there .... 3.3l engine ....
View 1 RepliesA friend has a 1999 Caravan with the 3.0L engine. He couldn't get it to start and to make a long story short, I checked the fuel pump relay and fuse and they were good but there was no pressure on the fuel rail. Turning the key I couldn't here the fuel pump come on and determined the fuel pump was bad.
I changed the fuel pump and fuel filter put in 1/4 tank of gas and turned the key, and it turned over but wouldn't start. I can audibly hear the fuel pump come on for a second or so, and feel the vibration when I put my hand on it, but there is still no pressure at the fuel rail.
Last week, my van started chugging and the keydance code indicated random misfire. I changed the front spark plugs and wires and it ran a little better but still showed the error. Took it to my trusted mechanic and he changed the back 3 wires and plugs and the coil pack. Code now showed misfire on one of the back cylinders(I forgot which one). 2 Mechanics both confirmed good spark and gas at the cylinder. He is saying that there is a mechanical problem in the cylinder and the fix would be over $1k.
The van has over 250k on it so it's not worth the engine work. I asked about a compression test and was told that it's almost impossible to test the rear cylinders without doing a ton of work, and that they are 95% sure that it is a mechanical problem with the cylinder. I've known the mechanic for over 20 years and he is an honest guy, and knows that I won't do the expensive repair, so he's not trying to rip me off.
I don't have the facilities or knowledge to do the work, so it looks like I'm screwed. Is there anything else that I should be doing before I write the van off? It does run, but very rough at low speed, and no power at high speed, and mech says that the unburned gas will eventually screw things up.
Changed input and output sensor, replaced solenoid pack, cam and crank sensor. Runs good code on odometer 1684 p700.
View 4 RepliesI have a 96 Grand Voyager that had had sat for a year undriven or started due to being out of state. It ran like a champ when I parked it. Now I charged the battery and went for a drive on the freeway and my check engine light came on and started blinking. I had the code read it came back with 2 codes a P0306 and a P0300. I noticed that the cylinder 6 spark plug wire was arcing on the core support. So I replaced all the plug wires and spark plugs with Champion platinum spark plugs. I cleared the codes and took it on a test drive and the P0300 code came back. Is there anyway the old gas is causing the random misfire? or what else could it be?
View 1 RepliesI have a 1995 Plymouth Voyager se about a year ago the transmission started acting up, for no reason, it would just go it to First and never come out I would stop turn it off turn it back on again and it would be fine..then days later it would go by, it would do it again. it did this for a while and the good days would turn in to a mile or two then it just decided not to come out of first ever, during this, i took it to a trany shop and rebuilt the transmission it worked for a bout a half hour.
Final a mechanic friend checked the computer again and changed it out with another and it fixed it beautifully!!! ok well about a week ago a very odd loud obnoxious squeal started that sounded like a bottle rocket but not all the time, more often than not though. Before I got a chance to take it to my mechanic friend i was driving along and the transmission slipped in to first and wont that's it. i have been doing emergency trips in first gear and also the horrid squeal is gone. the thing have to be linked what should I try and i don't think its the computer, I really don't want to lose my van
The gear shift works fine, and we lifted the hood and saw that the mech. arm IS working when we shift. However, the van will not move into any gear. won't go forward, reverse, etc... it acts like it isn't shifting.
i was driving down the highway, and noticed it wasn't accelerating and stepped on the gas.. .and nothing. I stopped the van, put in park, turned it off. Started it again, and put in D and wouldn't go, just engine revved. then put in reverse and same thing... didn't move but engine revved.
I have a 2002 Town and Country LX with the 3.3L V6. Recently the check engine light went on and later the transmission stopped shifting from 3rd to 4th gear. All the gears work properly except for 4th. It doesn't seem like anything is wrong with the transmission, would this be a sensor problem? If so which sensor would need to be replaced?
View 14 RepliesMy 2000 dodge caravan with the 3.3 is shuddering while in gear and not moving especially in reverse . As soon as you start going it stops . No slipping whatsoever. The van only has 130'000 miles on it .
View 2 RepliesI purchased a 2004 Chrysler Town & Country Dec 2003. I noticed an intermittent problem with my gear shift indicator lights PDRNL were all lighting up when I would start the vehicle in February 2004. I would have to play with the shift lever a few times to get it into gear.
On Feb 26, 2004 the vehicle would not start at all, would not even turn over. The vehicle had to be towed to the dealership. It had 3500 miles at the time. The error code was PO706 check shifter signal. They said it was the transmission range sensor and replaced it. I had no problems for 2000 miles until I was in northern Michigan and the gear shift indicator lights started doing the same thing.
I brought it to a local Chrysler dealership the next morning and they scanned the following codes PO1791 loss of prime PO705 check shifter signal BCM stored TCM message not received FCM stored TCM communication fault DSD stored incomplete power voltage. This dealership checked connections and wiring harness which were okay so advised me to take it back to my dealership at home since they would have to tear the whole van down to figure out what was wrong and any parts they would need would not get there before I left for home.
Luckily, I made it home with only one incident with these lights coming on. My dealership had the same error code PO706 and also PO444. Here is what their repair order states "DTC PO706 shift signal fault. Front pump allowing torque convertor to bleed down IPM internally shorted causing intermittent shift signal errors and PO444 and PO706. Scan and perform trans diag and fluid level full R & I the transmission R & I the pan and valve body replace the filter R & I the front pump and replace the front pump and torque convertor called STAR about intermittent loss of shift signal was told to replace the IPM. Replace the IPM (power distribution center) retest ok at this time."
So here is my question....I am very worried with all that I am reading about transmission problems and this van has only 6500 miles and all these parts that they have had to replace already is really scaring me!
We just purchased a 2012 Grand Caravan and was wondering where to get a key and program it. I know the key will be an arm and a leg if i get it from the dealer. Is there a tutorial that tells how to program it as well?
View 3 Replies2006 Caravan. Heat comes and goes every minute or so. Also noticed the temp gauge goes from normal operating range to cold and back again frequently. Hasn't overheated. Does that sound like a thermostat problem?
View 2 RepliesOn my 2005 3.3L Grand Caravan the ABS light keeping coming on. I inspected the sensors for the front and used my compressor to give them a quick puff of air to get rid of dust. The light went off for about 5 days. Now it is back on.
How does one read ABS codes? If I knew for sure that the problem is a speed sensor and which one I could clean or replace the faulty sensor.
If I clean to sensor are there any special precautions I need to take? As far as I could see they didn't look very dirty.
What am i missing i have a terrible clunk in the front end when i hit bumps. I thought it was the struts and mounting plates so they are new . no change Stabilizer links were tight but i replaced them as well. Everything else seems tight but the noise has not changed with any of the above mentioned repairs.
View 13 RepliesI'm having trouble with my 96' 3.0L, its kind of crazy its intermittent and while driving the engines surges one or twice and then dies... when I try to crank it up again cranks but don't starts if I try again it wont even crank ( no starter winding up ) what I noticed is that is I'm driving when it dies my check engine light disappears for a while and if I connect my OBD 2 reader does not link up with the ECU if I wait a while and I crank it up again its starts and the while cranking up I can hear a bang noise from the engine compartment drives side and then after a couple of minutes dies again...
View 4 RepliesI have a 2006 Grand Caravan 3.8 that just stalled at a set of lights yesterday and have had it towed back to the shop here. I turns over and starts briefly then will die and then just turn over strongly. I cleaned the throttle body and IAC but this did not work. I connected fuel pressure tester and have no pressure when turn key on or turn it over.
The fuse and relay check out ok, so I'm thinking bad or clogged fuel pump.
I have a 2004 Caravan out back that I have used for other small parts to interchange before and was wondering whether or not the fuel pumps between these two are compatible. Be a lot of work to pull the one off the one in the yard, only to find out its not going to fit.
142k, having some problems lately, the van won't accelerate now and again, moreso when the engine isn't up to temp, but lately it's gotten more and more prevalent. I have done some recent and needed maintenance in hopes of fixing the issue, but to no avail so far. I've replaced the plugs and wires, air and fuel filters, and both upper and lower O2 sensors (first replaced the upper with a Bosch, almost immediately had problems with P0134 code, so instead went with a Denso, hasn't come back yet). I checked fuel pressure, 60 psi sitting in the shop, the cat doesn't seem to be clogged, and it idles fine all day long.
Problem resembles running out of fuel, or more maybe like I'm letting off the gas, but my cheap scanner says the TPS is working fine, and I was watching the TPS percentage as I was driving it was reading normally. As I'm accelerating slowly from a stop, it'll start to cut out around 30 mph, but speed doesn't seem to matter, if I accelerate sharply it just bogs and slows down, if it does shift up a gear, the rpms will jump to about 5k, then slowly decrease even if I've got my foot on the floor. I keep coming back to the fuel pump, but I don't have a long enough hose to have it connected while test driving. Considering removing the hood so I can prop the gauge up so I can see it while driving. I am getting a P0132 code now, but I'm more concerned with the accelerating issue.
Intermittently the ABS Light is coming on. 84,000 miles.
Brakes have been changed once, 10,000 miles ago.
Minor clunk sound when light is on.
Light goes off after van has set, brakes work fine at that point.