Elantra XD (2001-06) :: Check Engine Light Turned On - Codes P0422 And U0D00
Jul 10, 2014
While on my 20 mile commute my check engine light turned on, attached the code reader to the car and got codes P0422 and U0D00. Looked up the P0422 code to find "Caralyst efficiency below normal (bank 1)" I have a list of possible fixes but have no luck finding out about the U0D00 code. I notice I lose and a quart of oil every month and when I start the car, the first 5 seconds or so the engine revs to 4000 rpm.
View 1 Replies
Advertisement
How to diagnose the following codes: U0D00, P0711, P2300.
U0D00 - What this means.
P0711 - Transmission Fluid Temperature Sensor "A" Circuit Range/Performance. How would I go about fixing this?
P2300 - Ignition Coil "A" Primary Control Circuit Low
View 4 Replies
I've replace the input and output transmission speed sensors on my 01 GLS. check engine light is on again for 2 P0501 codes. There is no abs speed sensor on the left side but there is on the right side which doesn't look like it is seated correctly. The transmission is still shifting kinda funny sometimes. Should I have abs speed sensors on both sides? And what else should I do to fix the random erratic shifting?
View 3 Replies
Have an 01 elantra as a second car and it's great. Just recently tho the check engine light came on and I've got a few codes that make sense since there has been some odd issues with it in the past month or so.
02 sensor CKT bank 1 sensor 2 (slow response)
shift solenoid D malfunction
shift solenoid C malfunction
shift solenoid B malfunction
Trans range circuit malfunction (PRNDL input)
So I know the 02 sensor needs to be replaced, that's fine. I'm more concerned about the rest of the codes because when cruising around 40mph the car tries to shift to 4th gear or something like that, it will bog down because the rpm is too low (maybe its overdrive, not sure).
That's a minor issue but has been there since we got the car over the summer, the bigger issue is the last couple of days, i've noticed that when driving the car around the city, slow down - turning - and then accelerating the engine/trans will buck harshly a few good times before it smoothens out, my guess is the gear change didn't go well.
View 13 Replies
I have a 2001 Elantra GLS, 160,000 miles. These two codes come up on ny diagnostic tool.
P0422
Main catalyst efficiency below threshold (bank 1)
No symptoms at all
P1529
Customer snapshot request
Symptoms
Car will shift hard into third gear and stay there without shifting at all regardless of speed. Shutting the car off and restarting will sometimes fix, but only temporary. When car runs normal, it runs fine and shifts good. At speeds around 40 it seems to kick back and forth between 3rd and overdrive as if it can't decide where to be. Tried replacing speed sensor, but new sensor did not fix problem.
Fuel Sys 1 CL
Fuel Sys 2 NA
Calc Load 18.4
ECT 201
STFT B1 0.0
LTFT B1 -2.3
MAP 8.6
Eng RPM 3351
Veh Speed 22
EV flashing
O flashing
View 17 Replies
I have an 05 Elantra GLS auto transmission, ~83000 miles. Last Friday, the car was driving fine. I didn't drive it on Saturday, but when I started it up Sunday night, that's where the issue began. First, when I shift into reverse, the car makes a noise like as when you go over a pot hole. Idle RPM is around 800.
When I press the gas pedal, usually the response from the car to go forward is almost instantaneous, but now it take a second or two from the time I press down the gas pedal to when the car moves forward. The process is smooth though, no hiccups as it does that. Next, when I was driving on the highway between 70 - 80 MPH, the car's RPM was 4000 - 4500. It even sounds like the engine is "working harder" than it usually does. The 'Check Engine' light is also on with these codes: P0700 and P0885.
Another thing I noticed is that the car alternates between running fine and running with the conditions described above. If the car run with the symptoms described above, I shut off the car and restart it. Then it will run fine, but the check engine light will stay on. Then if I turn off the car and restart it, it will go back to the mode where I have the issues.
From some research, the P0700 code just means that the TCM has the actual code which is P0885. According to the tech manuals at [URL] ...., the P0885 has the following probable causes.
- Malfunction of the A/T control relay
- Malfunction of connector
- Malfunction of the PCM
The car actually ran fine today, with out any issues but the Check Engine light is stuck on. How to replace/service this PCM item? Or maybe this issue is covered under 100,000mile warranty?
View 3 Replies
I just purchased a 2005 elantra with 133k on it and she runs fine other than a slight erratic idle. And by slight I mean it will jump about 50-100 rpm idling and every blue moon it will jump up to 250 rpm sitting there. After idling for a while my CEL came on with the following codes.
P0507 idle air control rpm high
P0506 idle air control rpm low
P0170 fuel trim malfunction bank 1
P0121 throttle position sensor
What could be causing this? I took the iac off and cleaned it with maf cleaner but it didn't work.
View 9 Replies
Engine light come on and everything is running great, this morning got this error code U0d00. Went to advanced auto and had them run a scan.
View 5 Replies
I have a Hyundai Elantra 2007 with 123,000 miles on it. Three weeks ago the engine About two weeks ago the engine light turned on. I took it into an auto parts store so they could use the digital code reader, it said the upstream O2 sensor needed to be replaced. I replace it and still have bad gas mileage, the second time I had it read with the code read it said both of the O2 sensors were bad so I replaced the downstream one week later. There was still bad gas mileage and the code reader still said it was both of the O2 sensors, the auto part's representative said when the engine light is on that the computer turns off the O2 sensors so he recommended to erase the codes on my car with the code reader (I pushed the button and he looked away). Still nothing changed so I disconnected the negative terminal on the battery to restart the computer. Still horrible gas mileage with no engine light anymore. Gas mileage averages about 15 mpgs in city and 32-35 on the highway. The highway seems about right but I've never seen any mpg below 30 for city mpg before this problem. I also cleaned the mass air flow sensor with mass air flow cleaner after dealing with the O2 sensor. All preventive maintenance is kept up by me and I have had no problems with this car before. Water pump replacement, timing belt replacement, and transmission flush have occurred in the last ~50,000 miles.
View 19 Replies
Got this engine code error, how to proceed?
I have a '00 accent, just purchased a few days ago from a private party, when I bought it, I had a mechanic look it over, gave me the OK and said it passed inspection, no mechanical or obvious running problems with the car.
So I was driving around yesterday and the check engine light came on, took it to get the oil changed because I wasn't sure last time it was done, had the oil changed, light stayed on.
So I took it to auto zone to read the error code, was given this information. How to proceed?
View 1 Replies
My check engine light popped up the other day and when ran, 3 codes popped up: p2414, p2195, and p0170. From what I could gather it looks to be the O2 sensor is bad. This would be the one on the exhaust manifold, correct?
Also, what would cause the o2 sensor to go bad in the first place? My 09' has roughly 65k miles.
View 13 Replies
We have a 2002 elantra...went to auto zone and they ran the test and came back with code u0d00...but they didn't have an answer for it in there computer..
View 4 Replies
We have Elantra - 4 Door sedan 2006 model. We have not driven much; about 23000 miles. All of a sudden we got Check Engine Light ON. I took the car and got it tested at Pep Boys to get codes. It came out as PO700 and PO885.
View 2 Replies
I bought the little car to get off my motorcycle and its done great. But, after a couple trips around town my check engine light came on, and I imiditely noticed a change in my idle and engine performance. Im assuming my engine changed the air/fuel ratio to account for the sensor indications. My initial code read came back with four codes which said something about spark, and O2 sensor, and emissions. I went ahead put new spark plugs, gaped them as well as replaced the first O2 sensor.
After that I reconnected my battery and sure enough no engine light and my idle felt even better than before. (by the way my old plugs looked normal) But shortly down the road the light came on again. My idle did become a little different but not like my first encounter with the engine light. My power too seems a bit degraded, as well as the engine's sound. As of right now I am only reading one code P0422, which I do not see in the manual. I read online that its probably my catalytic converter or my engine is running at an improper air/fuel ratio. I am praying that it is not my catalytic converter and just my engine computer throwing things off.
Other things which may serve as clues:
Slight valve cover gasket leak (I will change the gasket when I do my timing belt job along with other seal and probably the water pump)
When pumping gas I can get about 90 cents in at a time, now more like 40 cents since the Saudis lowered our gas prices. Assuming I've got some kind of venting problem.
Car has 107K manual shift.
View 9 Replies
I recently purchased an 06 f150 fx4 5.4L with 60K miles. Just recently my check engine light came on and I've noticed a slight rough idle in park. I took it to autozone and the code read P0422 evap emission leak. Bought a new fuel cap but didn't work... EGR valve?
View 2 Replies
I have a 2011 Elantra that I purchased brand new. Has over 60,000 miles on it. Had a check engine light come about year or so ago which was fixed with a software update at the dealer.
Check engine light is back on now. Steady light; it's not blinking. Brought it to my mechanic. Ran diagnostic and said the oxygen sensor needed to be replaced. P codes were P2096 and P2196. He ordered the sensor from the dealership and installed it. Reset my cars computer. I drove the car 26 miles and the engine light came on again.
Here are my questions:
1. Wouldn't my mechanic's diagnostic equipment tell him what the problem or all the problems were? Why would it tell him the oxygen sensor needed to be replaced when there seems to be another problem causing the engine light to come on?
2. Would the dealership have more insight into a check engine light system problem than a mechanic shop may have?
View 45 Replies
I have a 2001 Ford F-150 v6 2wd. A few weeks ago, the check engine light turned on so I drove to the nearest autozone to hook up their computer and see what the error code was. The technician gave me the code (I don't remember it off the top of my head but it wasn't something imminent). Before leaving, I asked him if he could clear the light, figuring that if it didn't come back on after 50 miles, that it might have just been a fluke with one of the truck's sensors. Later that day, I realized that when I started the truck, the check engine light was no longer turning on momentarily the way that all the dashboard lights do to tell you that they're working.
I went back to a different autozone (one closer to my house) and explained the situation. They checked the computer for codes again and found none and said that the light must not be turning on because the bulb is burned out. I find this to be a striking coincidence that the bulb should happen to blow out exactly when the technician used his computer to clear the light. Is it possible that he did something with his computer that permanently disabled the check engine light? It's been a few weeks and I've since bought an inexpensive bluetooth code reader of my own, hooked it up, and found that there is still no active code. Is it possible that the code has returned or will return, but that I won't have a way to know because something he did suppressed not just the light but my car's code reporting mechanism?
For now, the truck drives fine, but I'm afraid to travel long distances when there might be a problem I don't know about.
View 7 Replies
My '04 santa fe 3.5 v6 gls/lx, 79k miles, gas, auto, check light has just come on while I was driving a less than 10 mile journey. How can I check what is wrong. Do I need some sort of diagnostic code checker. Do any national outlets check it for free (Pep Boys or Auto Zone, etc).
Just 5 days ago (about 50 miles only) I had timing belt, water pump, plugs and leads replaced, brakes checked and lubes flushed; BUT not at above dealers. I would rather know what the code is saying before I go back to the shop who carried out the work.
View 12 Replies
I have had a check engine light go on and off with P0700 and P0741 but since the flush day 3 it hasnt come back on and it was chucking with rpm doing small jumps... but now it does it in the mornings after sitting all night after a few chucks its fine for the rest of the day til the next day no check engine light so far, but transmission flush has worked a lot not as bad as before the flush.. So what else could be causing it? Its a 2006 hyundai santa fe with 274,000 kms.
View 24 Replies
I have a 2002 SF GLS/LX (?) with 2.7 L V6 2WD (60,000 miles) and it started to apply the ABS brakes in a random manner. Found out it was caused by a broken front wheel tone ring. So, I pulled the ABS fuse under the dash and it stopped the brake problem. Drove it today to pick up some wood and now the check engine light has come on.
My neighbor has an OBD scanner and he plugged it in and said I have a P0501 code and a P1529 code, but he didn't know what they meant. What they mean and are they related to me pulling the fuse under the dash? Did I pull the wrong fuse? Is there another fuse somewhere that I should have pulled?
View 1 Replies
My check engine light came on the other day, with no symptoms or problems. Today I stopped at the Auto Parts store and had the codes read. They were P0440, P0441, P0446, and P0301. They are for the EVAP system and misfire.
I had read here that one of the codes could be for the gas cap so I tightened it and then, also as read on here, disconnected the negative 12 V battery cable to perhaps clear the check engine light. I was curious.
When I started the car again, I now have not only the check engine light, but the red triangle exclamation point. How would you proceed? The 12 volt battery is around 5 years old. The entire exhaust system was replaced last year.(not O2 sensors though)
The hybrid battery was replaced at 70,000 miles and I now have 110,000 miles on it. I really wonder why disconnecting the battery and reconnecting it caused more error lights to appear? Also, the Auto parts guy said his code reader was fine for my car but I seem to remember here that there may be a special Prius one.
View 6 Replies
