Elantra MD (2010-15) :: Check Engine Light Steady Not Blinking - Codes P2096 And P2196
Jul 24, 2015
I have a 2011 Elantra that I purchased brand new. Has over 60,000 miles on it. Had a check engine light come about year or so ago which was fixed with a software update at the dealer.
Check engine light is back on now. Steady light; it's not blinking. Brought it to my mechanic. Ran diagnostic and said the oxygen sensor needed to be replaced. P codes were P2096 and P2196. He ordered the sensor from the dealership and installed it. Reset my cars computer. I drove the car 26 miles and the engine light came on again.
Here are my questions:
1. Wouldn't my mechanic's diagnostic equipment tell him what the problem or all the problems were? Why would it tell him the oxygen sensor needed to be replaced when there seems to be another problem causing the engine light to come on?
2. Would the dealership have more insight into a check engine light system problem than a mechanic shop may have?
View 45 Replies
Advertisement
I have a 2013 Elantra GLS with almost 200k on it. I am the original owner. I have only had a few small problems with it just replacing lights and had to replace the passengers side wheel bearing twice. the rest has just m=been replacing wear and tear parts. the check engine light is on because it needs 02 sensors. They are back ordered. The car started idling roughly and driving horribly on the way from Rhode Island to New York on Christmas day. A friend had a diagnostic machine and the code read misfire cylinder 3 p0303..I am assuming it damaged the catalytic converter and that I now need both the sensors and the convertor. I live about 7 miles from my garage. should I tow it ? or drive a t a low speed? Have to bring it in first thing in the morning. What else could be wrong?
View 3 Replies
My Girlfriend just got a 2003 Hyundai Elantra and everything was running great on it the first month she had it BUT the check engine light was on.. After about a month she called me up while driving and said that the check engine light was blinking and the car would hardly move. So I got to the car and looked at it and I noticed the oil filter was a little loose so I tightened it good this time and added a little bit of oil. It actually moved but it would hesitate. So we had it towed to a shop and they read the codes from the check engine light and told us it was leaking oil from the motor some where (not specific) and it also needed a new O2 sensor.
So I replaced the catalytic converter underneath the car and also a new sensor along with a new set of spark plugs. It ran alot better and I left it at that. Now about a week later she was coming home and noticed that when she turned left or right that the battery light and brake light on the dash came on. She drove it home and when she turned in the driveway the car went dead. It started right back up and we got it to the house and left it over night. I went out this morning and again it started right up. but when I lifted the hood I noticed the belts on the pulleys were all spinning very slowly. I'm not sure if it could be a timing chain or if it just needs new pulleys.
View 6 Replies
I love my car 2012 Hyundai Accent GLS but once it hit 60K miles, the engine light came on and it has been eating gas. I get up to 160 miles per tank now. My MP fluctuates from 12-25 MPG. I literally watch it jump when I fill up the car, then a few miles later, it drops again. Code P2196 always comes up. (stuck rich)
Dealer advised me to do fuel system flush.
Dealer replaced upstream o2 Sensor
Dealer replaced Check Valve
New Spark Plugs last Fall due to hearing really loud spark knocking... and also re-gapped last week. Now I can hear them slightly again.
Engine light just came back on after almost 200 miles.
Reading some other threads- apparently this seems to be a known issue for my car.
I am wondering if I should try replacing the downstream o2 sensor.... OR consider trading my car.
View 3 Replies
Check engine light came on while driving home from work. The car seems to be running fine but I got the following codes p2195, p0420, p2096. I have a 2006 elantra with 184000 miles. Should I just replace the upstream oxygen sensor or is there a more likely problem? I rather not spend the money if this combination of codes is likely has a different cause but replacing the sensor appears to be the quickest and easiest solution.
View 5 Replies
04 r32 CEL just came on. 1st blinking now just on steady. Timing belt, coils, plugs, wires, ecu and then some done at dealer within last 3,000 mi and still?
View 5 Replies
I've replace the input and output transmission speed sensors on my 01 GLS. check engine light is on again for 2 P0501 codes. There is no abs speed sensor on the left side but there is on the right side which doesn't look like it is seated correctly. The transmission is still shifting kinda funny sometimes. Should I have abs speed sensors on both sides? And what else should I do to fix the random erratic shifting?
View 3 Replies
My check engine light popped up the other day and when ran, 3 codes popped up: p2414, p2195, and p0170. From what I could gather it looks to be the O2 sensor is bad. This would be the one on the exhaust manifold, correct?
Also, what would cause the o2 sensor to go bad in the first place? My 09' has roughly 65k miles.
View 13 Replies
Have an 01 elantra as a second car and it's great. Just recently tho the check engine light came on and I've got a few codes that make sense since there has been some odd issues with it in the past month or so.
02 sensor CKT bank 1 sensor 2 (slow response)
shift solenoid D malfunction
shift solenoid C malfunction
shift solenoid B malfunction
Trans range circuit malfunction (PRNDL input)
So I know the 02 sensor needs to be replaced, that's fine. I'm more concerned about the rest of the codes because when cruising around 40mph the car tries to shift to 4th gear or something like that, it will bog down because the rpm is too low (maybe its overdrive, not sure).
That's a minor issue but has been there since we got the car over the summer, the bigger issue is the last couple of days, i've noticed that when driving the car around the city, slow down - turning - and then accelerating the engine/trans will buck harshly a few good times before it smoothens out, my guess is the gear change didn't go well.
View 13 Replies
We have Elantra - 4 Door sedan 2006 model. We have not driven much; about 23000 miles. All of a sudden we got Check Engine Light ON. I took the car and got it tested at Pep Boys to get codes. It came out as PO700 and PO885.
View 2 Replies
I have an 05 Elantra GLS auto transmission, ~83000 miles. Last Friday, the car was driving fine. I didn't drive it on Saturday, but when I started it up Sunday night, that's where the issue began. First, when I shift into reverse, the car makes a noise like as when you go over a pot hole. Idle RPM is around 800.
When I press the gas pedal, usually the response from the car to go forward is almost instantaneous, but now it take a second or two from the time I press down the gas pedal to when the car moves forward. The process is smooth though, no hiccups as it does that. Next, when I was driving on the highway between 70 - 80 MPH, the car's RPM was 4000 - 4500. It even sounds like the engine is "working harder" than it usually does. The 'Check Engine' light is also on with these codes: P0700 and P0885.
Another thing I noticed is that the car alternates between running fine and running with the conditions described above. If the car run with the symptoms described above, I shut off the car and restart it. Then it will run fine, but the check engine light will stay on. Then if I turn off the car and restart it, it will go back to the mode where I have the issues.
From some research, the P0700 code just means that the TCM has the actual code which is P0885. According to the tech manuals at [URL] ...., the P0885 has the following probable causes.
- Malfunction of the A/T control relay
- Malfunction of connector
- Malfunction of the PCM
The car actually ran fine today, with out any issues but the Check Engine light is stuck on. How to replace/service this PCM item? Or maybe this issue is covered under 100,000mile warranty?
View 3 Replies
While on my 20 mile commute my check engine light turned on, attached the code reader to the car and got codes P0422 and U0D00. Looked up the P0422 code to find "Caralyst efficiency below normal (bank 1)" I have a list of possible fixes but have no luck finding out about the U0D00 code. I notice I lose and a quart of oil every month and when I start the car, the first 5 seconds or so the engine revs to 4000 rpm.
View 1 Replies
I just purchased a 2005 elantra with 133k on it and she runs fine other than a slight erratic idle. And by slight I mean it will jump about 50-100 rpm idling and every blue moon it will jump up to 250 rpm sitting there. After idling for a while my CEL came on with the following codes.
P0507 idle air control rpm high
P0506 idle air control rpm low
P0170 fuel trim malfunction bank 1
P0121 throttle position sensor
What could be causing this? I took the iac off and cleaned it with maf cleaner but it didn't work.
View 9 Replies
I have an 03 Explorer 4.6L that is running bad. The code was P2196, I changed B1S1 O2 sensor and cleared code. A few minutes later the SES light was on, I checked codes and now I have P2196 (again) and P0405. Why I was only getting the O2 code and now I have it again after replacing it and a new code (0405 EGR)..
View 14 Replies
I'm due to leave at 6am sharp on Friday morning for that pre-planned surprise 50th Bday celebration I've been talking about for my wife. This evening I get in the Elantra to pick her up and when I started the car it began to shake VIOLENTLY, like I was in a commercial dough mixer. WTF!?? I saw the check engine light was on so I shut it off immediately. Curiously, I had the car out earlier without incident.
I restarted the car and it ran smoothly this time, but the check engine light remained. Calling the dealer, I was able to get a 9am appointment for tomorrow morning. I don't have an OBD-II scan tool to check the codes, but based on the symptoms, and recent poor gas mileage.
View 31 Replies
So the check engine light on my '12 with 5K miles came on 2 days ago. Called to make an appointment at the dealer for tomorrow...and today it goes off. Is it relatively safe to fore go the appointment and see what happens? I don't think it was related to the gas cap.
View 2 Replies
I just bought a used 2011 Elantra GLS and am having some issues that the dealer cant resolve. What is happening is the the Check Engine light comes on and off. It will be on for a day or so, then go off for a day or so, so I am thinking its the gas cap. So I tighten that thing up as good as I can and pulled the negative battery terminal and problem solved. About 2 days later, and about 200 miles later on the same tank of gas, the light pops back on. So I call the dealer and took it there the next day.
On my way to the dealer, the light goes out. They try and pull the code, but the ECU is showing nothing. I asked if the ECU stores codes and I was told that when the light goes out on its own it clears the ECU of the code. Not sure if that is true, but that is what I was told. So I drive the car home. I fill the car with gas, drive about 100 miles and the light comes on. I call the dealer the same day, take it over, and on the way like the car knows it goes off and guess what? Dealer cant do nothing.
Now to make a long story longer, this is what I know. The car is not a CA car. It was sold in GA and was a prior rental. It ended up in CA and was sold as a certified pre owned from a Hyundai Dealer, I actually bought the car from a Mitsubishi Dealer and they dealer traded for this car (thats another long story) the carfax does show that it failed emissions but passed after several attempts. Which I thought was odd on a ULEV vehicle. Since I liked the car so much and the price was good, I bought it since it did pass smog eventually.
Once I get the car home, I do my usual thorough look. I clean everything to my standards. I am cleaning the engine compartment and took the engine cover off. 1st thing I noticed was the Spark Plug Coil Packs all the 10mm bolts that hold them in were loose and 2 of them were completely off!! So I decided thats odd, so I pulled the plugs out and they were the NGK's so just in case I put a brand new set of the NGK laser Iridiums back in and tighten everything up. Then I notice where the PCV valve is on the valve cover, the hose that goes to that to the intake tube does not look stock. The hose looks like fuel line hose that someone put on it and the clamps are not stock. So I am canvasing for OEM replacements of those parts now. Then when I was installing the mud guards, on the drivers side rear tire where the gas filler tube is I notice another non OEM clamp. So someone was messing with this area of the car too.
The car is averaging 26-28mpg's in the city and I have been getting 35-37mpg's highway so I don't think there is anything major wrong here. I believe that either the PCV valve hose is kinked and may be causing a fault, or that since it was a prior rental that people were over filling the gas tank and maybe blew the expansion valve in the gas tank, causing the fault. I have no way to prove this since the light goes on and off and clears the ECU every time I take it in.
View 7 Replies
This morning started to drive to work and the check engine light came on or actually did not go off. Not sure which. Anyway it is a steady light not blinking and the car runs fine. Problem is that the warranty is out by about 3 weeks, not by mileage and I have an appointment at the dealer on Monday. If I take it to Partsource and have the code read will it delete the code or turn off the light. Just wondering as I don't want to spend money at the dealer if whatever is wrong is not covered under the emissions warranty if I can get the code and fix it myself. Don't want the code deleted either if the dealer needs it.
View 2 Replies
I have a 2015 Hyundai Elantra Limited. Lately, the check Engine light comes on when I accelerate from a full stop and stays on for 3-5 seconds. It has also happened when I accelerate to get on the interstate (that just started today). There is no issue with the car accelerating. Everything else seems to be fine. It's just the Check Engine light that is freaking me out a bit. I've had the car since June so I'm not ready for any major issues. It started two days ago. I took the gas cap off and put it back on last night to see if that was the cause but it's still happening today.
View 2 Replies
So I got gas 4 days ago and today the check engine light came on afterwards. Went to auto zone to read code and it had to do with the gas pressure being slightly low (gas cap). So I got gas and resealed the gas cap. Well, it's been about 2 days since then and it hasn't gone off. Does it need to be reset or does it take more time?
View 1 Replies
I have a 2012 Ford Fusion SEL. In late December, the check engine light came on (steady, not flashing). I took it to a local mechanic, as the nearest Ford dealership is a 45-minute drive away. He said an evap code came up indicating that there was a problem with the vent valve solenoid, not the capless fuel filler. However, he did not have the diagnostics to research it further.
As there have been problems with the vent valve solenoid, including a recall (for which we do not qualify), my husband bought and installed the part on Jan. 7. We both drove it several times since then, and the check engine light stayed off. But when I drove it today (Jan. 11), the light was back on.
View 19 Replies
