95 explorer 4.0l ohv. I go to take off and then come to a stop after about 10-15 feet, i just give it a little gas then lightly press the brake, rpm's drop to around 400-500 then back to normal. I have replaced:
IAC
MAF
Plugs & wires
Coil pack
intake manifold gaskets
fuel system cleaner
fuel filter
air filter
I have a 1997 forkd F150 with a 4.6L Romeo engine. I have recently rebuilt the engine and now since it is put back together I am having a issues that i cannot pin point. When the truck is running and in gear my RPM drop to around 500 or below and my oil pressure drops and comes back up when the rpm's come back up this an intermittent problem and I have replaced the IAC valve and every once in a while i get a P0401 code for the exhaust recirculation. I think I am loosing some kind of vacuum. It was not doing this when I tore into the truck. It seems to be running okay not hesitation.
View 2 RepliesI think it's possessed! My sisters vehicle, a 2002 Explorer with a 4.0 V-6, automatic, 2 wheel drive will just shut off. At first it acted like it would vapor lock. But it would start right away. then the a while later, (several months), it got where it would drop rpms and the engine shudders, sometimes not dying.
When this first started, the throttle body was cleaned, a new air filter installed, fuel pressure checked. Everything checked out and for a few days it ran fine. Then it started all over again. There has never been a code thrown. All of this goes on only when the ambient temp is above 70 deg.'s. below 70 deg.'s it runs perfect.
Last week it went to the mechanic again and a new crank speed sensor, fuel pump, and diagnostic done. He could not find anything wrong any where. Took it for a test drive and it dyed on the mechanic. Still no codes. What the problem might be? Every Mechanic that has looked at it has gave up, one even saying, " it's possessed."
Two weeks ago Sun, truck ran fine, however Mon morning all hell broke loose. Truck was running very sluggish and stalling while coming to a stop. My first thought was tune up. I replaced the plugs and wires. During this I found that i could not get a socket around the ever loved driver side rear plug so i was only able to replace 7 plugs however in that process i managed to break the metal coolant tube that runs to the heater core.
Aday later replaced the entire intake manifold,egr valve, egr tube, IAC valve, both coil packs, fuel filter, tranny fluid and filter. During the removal of the intake i looked at the rear spark plug and found that a screw had been wedged into the hole breaking the plug and got it changed now it is all back together and the truck runs amazing however did not solve the low rpms during stopping. ive replace the above and checked fuel pressure which is good.
I have a TPS sensor just haven't installed it yet not sure if it is related to the issue. Tranny guy says it may be a bad solenoid or TC however last night I reset the PCM and drove it it ran flawless. this morning the problem returned which leads me to believe its not the tranny. ok one last kicker that 6 experts have failed to answer when i manually put the truck into 2nd gear the engine dies! no studder no fighting just quits.
Truck is a 98 F150 4.6 V8 186,000 miles i have yet to
1) change TPS.
2) clean throttle body.
3) clean MAF sensor. n
Not sure if any of this has an effect on the issue. There is only a EGR insufficient Air flow code..
I have a 93 Nissan 240sx that exhibits weird electrical behavior. I've had the battery and alternator checked at two local Advance Auto Parts locations with results indicating no problems. The car starts and drives fine. Immediately after start, my automatic seatbelts are engaged and the RPMs drop to about 400 and the car shakes violently (while pressing brakes and even when not pressing brakes). RPMs drop anytime accessories are in use. When braking at a stop light, the RPMs drop and the car shakes again. Using my headlights causes the RPMs to drop but not a point where I feel shaking. The problem is worst at night when I am pulling up to my apartment complex with lights on, braking, and using my power windows to access my gate card reader. I don't know if this problem is related, but when I am listening to the radio and turn the volume all the way up, the radio keeps cuts on and off. I have a suspicion it's the grounds, but before I start tracing all my wires. I'd like to hear everyone's input. I determined it was the brake booster vacuum because it also happens when not using the brakes and pinching the line has no effect on idle.
View 10 RepliesI own a 2001 Ford Explorer and have had the regular wear and tear but this problem has me stumped. A few months back I had to change the auto body gasket because the truck would not go into gear. After doing this the truck ran fine, I also changed the tranny fuild and filter. The other day i went to back up into the garage and the truck stalled and died out. it started right back up and it runs fine in all other gears. (P,N, D, 1,2, 4x4 high and low) and the over drive is working fine. when the truck is cool and hasn't ran in a while i can start it and the rpms stay at about 1000 th 1200 and the reverse works great. Now when the eng. heats up to normal and i put in in reverse the rpms drop to about 4 to 500 and it stalls out and dies. I have cleaned the mass air flow sensor, the throttle body, and the IAC valve but still dying out. Im thinking it may be a vaccume leak or the IAC is bad and cleaning just wont do the trick. I have also read that it may be the back up light wiring that hooks to the tranny may be shorted out.
View 4 RepliesI have a 2000 Explorer 4.0 SOHC that I'm having a persistent problem of cylinder 3 misfire. I've changed plugs with Motorcraft plugs set to the proper gap, put on new wires and have checked the resistance across the ignition module, both primary and secondary without change. I doubt that the problem could be the ignition control module as only cylinder 3 is affected. I have Auto Enginuity that I use to read the codes, attempt a repair and then clear the codes only to have P0303 appear again. Obviously the engine stumbles and has poor acceleration.
View 14 RepliesI'm in the military overseas and having a starting problem with my 2006 Ford Five Hundred. When the weather is cold, around 45 degrees F or lower the car starts OK however within about a second the RPM's drop between 400 and 500 and the engine starts to stumble. After about 3 to 4 seconds the RPM's gradually increase to around 1300-1400 RPM and is OK at that point.
View 5 Replies'99 Intrigue (3.5L) with 65k miles. The car has sporadic starting problems where turning the key in the ignition turns the starter motor and results in one of the following scenarios:
1) The engine does not turn on.
2) The engine turns on, RPMs drop and the engine sputters and dies.
3) The engine turns on with no problems (like this morning).
It does not appear to matter whether the engine is hot or cold.
Reading forum posts of people that have seen similar problems, several different solutions would seem to be in order:
1) Replace fuel pressure regulator.
2) Replace crankshaft position sensor
3) Replace camshaft position sensor
4) Replace fuel filter
5) Replace spark plugs
6) Replace idle air control valve
7) Clean the throttle body
Since I rather not start throwing money at the car by replacing parts one by one until the problem is gone.
1997 Subaru SVX (Alcyone) LSi, 3.3L H6 engine.
My SVX was driven from Denver to Las Vegas, NV and it developed an odd habit where the RPMs would start to oscillate while on cruise control. I had to disengage the cruise control to get the oscillations to stop. Three days later I was driving the SVX to work and the RPMs started oscillating at idle and the car started running rough and it died.
These things have all been replaced with OEM grade parts: Spark plugs, electric fuel pump & strainer & fuel filter, Mass Air Flow sensor, new air filter and fuses.
The car starts up fine but after a few seconds the RPMs begin to oscillate. Then the car tries to recover, the idle becomes rough, and the the RPMs drop very low and the engine shuts off.
I have a 2010 Santa Fa GLS. 88K miles. This issue started in the last 6 months, once the engine turns over the RPM drop low and starts to putter as if it is not getting enough fuel. If push down the gas when starting it works. Once it passes the first 2 -3 seconds everything is fine. No issue idling or driving. What this could be? It's not an issue with Starter, Battery, my best guess would be a sensor, leaky fuel injector.
View 1 RepliesMy '99 Saturn SL2 has from time to time in the past year or so had brief bouts where the engine will suddenly rev up to about 2000rpms while at a stop and/or drop down to about 650rpms combined with surging and stalling while moving. The Service Engine light would typically come on in conjunction with these spells, but then a few days later, things would be back to normal and the light would go off. The episodes seem to correspond with weather that has high humidity, but not necessarily extreme heat. Once or twice when the heat was above 90, the car quit completely and wouldn't restart for several minutes, but that was last summer.
About a month ago the car, which is normally parked in a garage, spent the whole weekend outside when we had some extreme rains (in air temps only about 60s or so). Since that weekend, the car is running frequently with the issues previously described, especially the surging and stalling while driving. It will feel like the timing of the fuel is all out of whack, will shudder and run hard, and then it will suddenly correct itself and run normally. A friend has a code reader and the codes that came up are 404 and 1404, which indicate the EGR valve. We replaced that with a new one and put in 4 new spark plugs, but the problem still persists. I believe the fuel pump is in the gas tank, so from other things I've read, a vapor lock may not be the problem since the fuel is being pushed.
Twice now this has happened to me and I'm concerned it will become worse if I don't fix it. Driving down the road my engine has disengaged. By this I mean the vehicle both times has been at 55 MPH, my foot on the throttle rpms riding around 1300 revolutions, and the engine disengages rpms drop below idle and my "wait to start" light comes on. This both times lasts approximately 2 seconds and throttle reengages while still traveling 55 MPH, "wait to start" light goes off and its like it never happened. What's going on with my truck? Ford diesel 97 250 7.3 ...
View 2 RepliesI have a 1999 Camry. I just spent $1250 (half of it borrowed) to have some basic maintenance, diagnosis, and serious repair work done. More than half of the serious (translate: expensive) work involved replacing a charcoal canister and installing a thermostat. The check engine light had been on for at least 10 years. And I had a gas pumping problem by way of the pump shutting off after only pumping a few cents worth of gas. Needless to say it was a royal PIA to fuel up my car. As far as the check engine light, a friend would clear the code so I could have it inspected.
Then more than 2 years a shop took out my thermostat because a hose had sprung a leak and they rigged up a temporary hose until they could order the part. I never went back because I couldn't afford it. I know it wouldn't have been a terribly expensive repair, but at the time it was more than I could afford. So for almost 3 years I have driven with out a thermostat and also couldn't get it inspected.
Fortunately I was finally able to get the necessary repair on my car--replacing the charcoal canister and thermostat--so that it could be inspected. I picked the car up yesterday and everything felt fine and the car ran fine.
Today I drove it about 12 miles from my home, made 3 back-to-back errand stops of not more than 15-20 minutes each and everything seemed fine. Nothing felt or sounded out of the ordinary. Then when I was leaving my 3rd stop, the car would not start unless I gave it gas. And it wouldn't stay started unless I gave it gas. In other words, the car would go, but as soon as I would take my foot off the gas to press the brake to put it in gear, the engine would die. There was no problem restarting it as long as I gave it gas, but I could not let off the accelerator at all or it would immediately die.
The car would go just fine, but if I let off the gas for any reason, even if I was driving 40 miles an hour on the street and let up completely off on the accelerator, the rpms would immediately drop to 0 and the engine would immediately die---no noise, no shuttering, no nothing---just die. This problem occurred almost the whole 12 miles back to my home. Then when I got about a mile and a half away, it went back to behaving completely normal and did not die when I let off the gas.
IOur 2003 suburban often gets a "reduced engine power" displayed by the computer and the RPMs drop to below 1,000. The vehicle will not accelerate and will not go above 1,200 RPMs no matter how much gas it is getting. Flooring the gas pedal has absolutely no effect and the truck continues on its merry way at about 20 miles per hour.
I have been told by various amateurs that it is the gas lines or electronics that regulate the gas flow. The reduction in engine power seems to happen randomly, but most often if the vehicle is idling for too long (and I'm sure the 110 degree heat doesn't work). I can get it fixed much quicker if I know what the problem may be.
Cold start. engine starts but wont idle, just dies. rpms drop. Restart same. Must neutral drop to get going keep rpms up until engines shifts then things are fine until next cold start. Cleaned throttle, changed air filter, dry gas, injector cleaner, no warning signal, scans clean. 180k miles.
View 6 RepliesAfter I fill my 6 cyl 2004 Hyundai Sonata (280,000 km), the engines starts, then stalls. I can only get it to work by keeping the accelerator pushed to ensure sufficient rpm's. If I remove my foot from the accelerator, the rpm's drop to zero.With the engine revving, I put the car in drive and 'lurch' away from the pump. After that, everything is fine. It starts up properly … until the next fill. My mechanic is mystified and I am frustrated.
View 6 RepliesI have a 1998 Accord, 4-cylinder VTEC standard transmission, 226,000 miles. Last fall I first experienced a problem with the car where within 5-10 minutes of starting the engine and driving, the engine seems to lose power/fuel and RPMs act as if they'll drop low enough for the engine to stall. If I take my foot off the accelerator, and reapply, the engine seems to gain power again.
Also, if I open the accelerator to full while the problem is occurring, it can occasionally "push through" and gain power again. Similar things will happen while stopped. In neutral, RPMs fall low and suddenly jump back up and then settle into normal idle. The problem never persists longer than 10 minutes within starting the car.
I took my car into a local shop that came recommended by a friend. They investigated a "check engine" light that didn't explain the problem and were never able to recreate the condition themselves. They replaced a few parts but lost the work order so I don't even know what they changed, but the problem seemed to have solved itself for a while. Recently it started up again and I would love to sort it out.
1998 Explorer 4x4 4L
The drive train freewheels when going down hill in 4x4 Low, and 1st gear. Shouldn't the engine be braking the vehicle when in 4x4 Low, and in 1st gear? It is free wheeling which is very hard on the brakes; I had to ride the brakes the whole 2 miles down (a lot 45 degree grade).
I've got a misfire problem with my Focus. It started about a month ago and did not trip a code until last week. It stumbles on acceleration between 2,000 and 4,000 rpms. It is only a slight stumble and although noticeable, it does not impede driveability much. Last week I was able to get it to finally trip an OBD code. P302 - Cylinder 2 misfire. I changed the plugs and wires with no effect. I thought I had it narrowed down to the coil or injector until my wife noticed a new wrinkle.
Under normal driving conditions the misfire is annoying, but my wife found that if she turns on the A/C, it is undriveable and will not accelerate past 30 mph without some patience and a neck brace for the bucking. My first thought was the A/C compressor was freezing up. I turned off the A/C and left the blower on and it would not stop missing. I turn off the blower and it smooths right out to the annoyance I described first.
Right now I drive the car without A/C and blower whenever I accelerate. If I'm going a steady speed, all is well and I can run the blower and A/C.
I drive a 2005 Ford Explorer (automatic) with 84k miles on it. Recently when I was driving on cruise control at 35 mp/h down a hill and applied the breaks to make a turn, the engine completely shut off. The lights came on, the power steering went off, the engine had shut off. I pulled over, turned the key off, turned it back on and it started no problem. I drove it for 3 days without problems (and without using cruise control of course), then I took the car to a shop. They ran diagnostics on it, test drove it, but couldn't find anything wrong with the cruise control or the transmission. I don't think they tested this driving downhill as the shop is not in a hilly area. Tonight, I went down the same road again, 35 mp/h in cruise control, slowed down for the same turn, and the engine shut off again exactly the same way it did before. What this could be?
View 7 Replies