Ford 6.0L Power Stroke Diesel :: 2004 F350 - Rear Wheel Seal Blown
Sep 10, 2015
Have a 2004 F350 dually diesel 6.0 - will now be replacing the passenger rear wheel seal for the third time in 8 months - replaced 12/2014 again in 6/2015 - took in for extensive engine pairs 7/8 got back 8/27 and have to replace the wheel seal again. Cannot figure out why blowing out so often - what to do to stop it from blowing out? Called the dealer and they were absolutely no support at all - mentioned something about a thicker seal?
View 10 Replies
Advertisement
I was getting ready to replace the carrier bearing and noticed the rear pinion seal is leaking. Before attempting the replacement myself, I would like some opinions on the noise in the video below. Is this normal? I am confidant I can replace the carrier bearing and pinion seal, but not sure I have the tools for anything else.
YouTube ...
View 4 Replies
A few weeks back my rear drivers side wheel started smoking severely...when I stopped you could smell the brake material, feel the heat coming from the wheel, and lots of smoke. I speculated it was the parking brake that got hung up. I jiggled that cable around and then went around the block - no issue. Note: I did not leave the parking brake on.
It happened again a week later, but not as bad. I took it into the dealer today. They said heat was evident as it burned off a sticker on the disk or caliper hsg area. They have not determined yet if it is parking brake or caliper?
View 14 Replies
04 f350 drw 2x4 ... I know this is a weird question, but i put 4 new tires on the rear of my truck and developed what i can describe as "loose body" symptoms. Most noticeable in going down the highway it feels like the rear of the truck sways and its hard to control and keep straight at times. Check tire pressures n front and rear suspension for broken springs or loose joints. Nothing looks broken or out of place. Prior to replacement truck drove straight n all was good. Also noticed steering wheel is now off center.
View 9 Replies
2011 F-350 CC, 45k miles... Found out yesterday mine is leaking. Way to early for these issues to pop up.
View 1 Replies
Had oil seal failure on the rear differential at 35,000 miles?
View 6 Replies
I am tearing down my junkyard engine to prep it to put into my truck and I came across this on the rear main seal... is this a wear ring?
It kinda looks like a oil slinger. My new seal is on the way so I have nothing to compare it to.
I don't want to be yanking on it if it's supposed to stay.
View 6 Replies
I haven't had time to take my truck to the dealer to actually be checked yet but it appears I might have a rear main seal going out from what I can see. I pressure washed the whole underside of my truck the other day and there is fresh oil where the engine connects to the transmission.
My truck is a 2011 with a 2013 engine in it. The truck has 103,900 miles on it. The engine has almost 60,000 miles on it. I have the extended warranty on it which is good. All this truck has to do is last 2 more lousy months and I'll replace it.
2011 Ford F-450 6.7L Diesel 12' Flatbed
View 5 Replies
I just bought a 2007 F350 CCSB 6.0 auto 4x4 with 113k miles on it, it does have the 5th wheel goose neck trailer hitch in the bed...anyway of course when I looked at the rig everything checked out and now I am getting a U1900 for ABS CAN communication...I should add that the ABS Light itself is not on, just the CEL...I have a feeling it has something to do with the wiring that the PO maybe had done to wire for his 5th wheel hitch?...I checked all the ABS related fuses in both fuse boxes and they're all fine...
While reading another post on the possibility of the brake pedal position switch up on the pedal itself being bad, someone mentioned that the wiring may be jacked up due someone adding wiring in for the 5th wheel hitch...I also checked the brake pressure switch on the nose of the master cylinder and that looked clean although I didn't test it...should I just replace these since they're pretty cheap or is there something I should look for in the wiring underneath the dash? Oh and of course my cruise control isn't working either...likely because of this ABS wiring issue..
View 14 Replies
I have a 2011 F-350 that came with the 5th wheel prep package which has rubber, two piece hole covers. Every time I slide something out of the bed across these covers they pop off or come partly off. I don't have a 5th wheel trailer and no plans to get one. Having trouble with the covers and come up with a better cover that would stay on when sliding cargo in and out. I hate just leaving the holes open to collect things. I wonder if some sort of galvanized electrical box cover would work with some sort of mount system under it?
View 14 Replies
I have about 70k miles on my truck and I've noticed just recently that my suspension is squeaking or creaking when I start to turn the wheel. What's the solution.... 2011 6.7 F350 super duty....
View 5 Replies
Got stuck, noticed when in four wheel drive only the front passenger side and rear passenger side was pulling. Is that normal? Or should both fronts be pulling?
2011 f350 dually 4x4 6.7.....
View 13 Replies
Just over 7000 miles all of a sudden I got this loud grinding noise in the rear end like a brake locked up. Pulled into a parking lot. Don't think it's brakes. Put the truck in reverse it got even louder for a second then it quieted down after that. Naturally this happened on a Saturday.
View 6 Replies
I have an 04 f-350 that I did an EGR delete, new Ford oil cooler, new radiator (not ford), new thermostat (not ford), coolant filter, glow plugs and harness, MBRP theoretical 4in downpipe (was 3.5 to converter) flushed cooling system with lots of tap water before the delete, replaced coolant with Cat 1 ELC and distilled water, fresh T6 5W-40 and filter, several weeks ago. Was troubleshooting a wireing problem and found what looks like oil sludge in the degass bottle while under the hood.
Possible that while doing EGR delete I clipped a gasket? Truck runs great, no smoke out the tail pipe. There is what looks like about a cup floating on top the coolant. Oil level is down about a 1/2 quart and clean, no water in it. Where do I start looking?
View 14 Replies
I have a 2004 Ford f 350 superduty. Everything runs great. Now the other day my fan came on and stayed on for three days now. It goes with my rpm so when I am doing a 100 down the highway in hopes it will disengage but won't.. Everything is Stalk.
View 3 Replies
I first saw them on the 2013 build and price and was thinking that I should look into adding them to my 12. I never got around to looking up part numbers. So, recently I thought of it again and after a little poking found that they could be had as a Ford accessory kit for around $110 depending on your dealer. MSRP is 133 I think. So, I hit the dealer and grabbed a set they had in stock. Install took 30 minutes. Very easy. They give the wheel wells a finished look and offer lots more protection than the small plastic strips on the rear that came with the truck. A hundred or so bucks well spent if you don't have them. There are aftermarket ones that are a touch cheaper on eBay by Rugged Liner but they don't work with the 5th wheel prep which I have.
View 14 Replies
I have a 04 F30 4x4 with a sick 6.0 power stroke. It has 230k on the mileage and ran good. I was driving at speed when she started missing like it had lost an injector and loosing power. The RPM's dropped under 1000 so I had to pull over off the highway. When i pulled over and put it in park it shutoff. Tried several times to get to start but after 10 minutes it started up. I drove about 2 miles and it started the same process. This went on 2 more times before I was able to finally limp home the 40 miles.
It never shut off again but ran very poorly. I put a new valve in and when I tried to start it just mad a pound clunking/clacking noise. The repair shop put a starter in it because it had stopped engaging and was going to ruin the fly wheel. I looked at it and it was eaten up pretty bad from trying to get the engine to turn over. So now all it will do is a single clunk and will not turn over. He says it could be a bad injector that flooded a cylinder or blown up in the bottom end. He did take serpentine off and still no go.
View 3 Replies
I have a 2004 f350 with a 03 bullet proofed motor. The truck did not have any power and the turbo wouldn't support until I put a new vgt solenoid in and it ran great for about 3 miles... Stalled doing 65 kinda lacked power while accelerating but got up to speed quick. I pulled over and no start. It is running error code kam on pcm from disconnecting batteries but could this cause the stall and no start? Or should I be looking into icp sensor?
View 2 Replies
About a month ago my truck was cutting out at one point it wouldn't even crank, got it going took it to the shop found my driver side battery clamp cracked, replaced it aswell as the egr valve because I had a p0401 code. Valve was pretty gummed up. Now recently it started doing it again. It cut out and it started right back up then later that night drove it two blocks and died, turn the key on and my glow plug light stayed on and wouldn't crank, was checking over all my connections and nothing seemed to be wrong. And then randomly it seemed like everything reset and my injectors would buzz, glow plugs cycled and fuel pump kicked on and started right up and drove home.
I replaced the pcm relay because one terminal looked to have gotten hot. Let her warm up in the driveway and she cut out twice but started right up. Checked over the connections again, replaced and cleaned both batteries, took it for a drive and no problems, later on started up again and let her warm up and cut out again, this time I got the p0401 code again. (Egr insufficient flow). I'm at a loss not sure where to keep going. It's an 04 f350 with egr delete, banks turbo and intake, with edge juice with attitude tuner on level 3 never switched levels around. And some other add on and mods that could make the list go on.
View 1 Replies
2004 later year 6.0 F-350. 155,000 miles. All stock.
It will start and run fine. Drove it for an hour then began running rough. Nursed it back home. When idling it eventually died. It will eventually fire up but runs really bad. It has done this a few times. I've done fuel filters and 911 fuel treatment because thought it was gelling. No luck...
It has injector circuit fault codes that pop up. Only other code is MAF sensor low but in range. First it was codes for cylinders 3,5. Then 3,5,8. Then 1,3,5,8. Now just injector 1. Keeps changing as I refresh. Battery power fine. FICM is 47.5- 48volts and in sync. ICP at idle is 600-700psi. IPR is 25%.
We had a problem with blowing turbo pipe off so may be overboosting. Not sure. No code thrown relating to that. Possible wire chafing? Maybe bad tank of fuel? Not sure where to turn at this point.
View 14 Replies
A little background, this is an 04, f-350. It sis not start a week ago so I charged the batteries and it started, started fine this morning, (had not driven it for the week) Drove it to work, 35 miles, parked it, and it will not start.
I downloaded Torque and got a few numbers,
HPOP 1900 FMP 48V (repaired last summer) and FVP 11.5V.
Ran out of battery to surf more and look, so I am trying to figure out the app, and the issue with the truck. It seems to turn over good, until I ran the battery down, and the GP cycles normally, and the injector buzz seems good. Temp is in the 50's...
View 14 Replies
