Ford 6.0L Power Stroke Diesel :: 2006 F350 Will Not Turn Over / No Start
Dec 5, 2016
This truck is bone stock FYI. I get in it to crank it and I get nothing. Batteries are good, everything in the cluster lights up, and looks normal. No codes are thrown. I can hear the solenoids click under the dash and hood. I check the voltage of ignition cable at the starter and I get no reading.
There is a single thick yellow with light blue stripe coloured wire on the passenger side of the engine compartment, beside the vacuum pump with a "squeeze and pull" type disconnect. Disconnect it, and connect the male half of the connector to the passenger side battery positive terminal. Do this with the ignition key in the RUN position. Does the truck start?
This is where it gets weird. The truck does start and after i reconnect the wire it it starts normal. I started it several times throughout the day. The next morning I get in the truck. No start. I have to use the wire and manually connect it to the battery and it starts right up again. This time I get a "Tow/Haul" light blinking on the dash. It will go into gear but pressing the acceleration pedal does nothing. I turn it back off, attempt to start it normally and it starts right up. No it will go into gear and drive. Now I am thinking maybe the neutral safety switch?
Could it be a solenoid sticking or the neutral safety switch or something else entirely?
View 14 Replies
Advertisement
I recently purchased a 2006 f350 with 6.0 power stroke. I drove it approx 15 miles shut the truck off, let it sit for approx 3 he's. Then I drove another 15 miles and shut it off. When I went back to it. To start it up would not start. The dealer said brand new injectors when I bought the truck. I tried to start it for approx ten min. I didn't want to bog down the battery. So when it wouldn't start I sprayed a shot of starting fluid and it took right off. But when you shut it off it won't start again.
View 14 Replies
I have about 70k miles on my truck and I've noticed just recently that my suspension is squeaking or creaking when I start to turn the wheel. What's the solution.... 2011 6.7 F350 super duty....
View 5 Replies
The truck seems to be smoking a lot when I do start it then once I drive it for a second the smoke stops. The truck will not start after the engine gets hot..
View 4 Replies
I have a 2006 F350 6.0L. That is Having trouble starting after it is warmed up. Ive been told multiple things it could be but the one ive been told the most is the Stand pipe or dummy plug in the oil rail having a small leak. Is this correct? Or is there something else i need to Check??
View 8 Replies
I have a 2006 F350 6.0 diesel with 110K miles. it takes me about 10 tries to get the engine to start. When it finally starts there is a lot of smoke and engine runs really bad. This isn't the case if I have the engine warmer plugged in. After warm up the engine runs pretty good.
My engine light comes on sometimes and will go out other times. I have tried sever attempts at adding injector cleaner with no results. Am weary about taking it to Ford for an analysis. Where to start with repairs? I did take it to Orielly auto and had the engine checked on their scanner. Approximately two pages of possible repairs come up.
View 3 Replies
We have two 6.0 trucks and one is having issues. A couple days ago it started to have white smoke like crazy upon startup, and when you slowed down you could see smoke, any speed and it dispersed so it was not noticeable. It got worse very rapidly and I haven't ha. A chance to work on it, it's also burning antifreeze, that's what the smoke is. Recently the egr started to act up so I cleaned it and the code for a sticky egr went away. It came back after a few months so I cleaned it, it went away for a few days then came on with the symptoms I just described. It has been moved at work a couple times the last few days, but not driven. Today I had to move it and it would not start, no white smoke either while cranking. I read the codes and this is what it has:
P0674- cylinder 4 glow plug control
P0404- EGR control circuit range/performance
P0299- turbo underboost
P0403- EGR control circuit
P0405 EGR sensor A circuit low
I would say it's a head gasket or EGR cooler, no? What course would I take to find out what's wrong? The truck in question is a 2006 F350 SRW King ranch. It has 115k on it, and the majority are work miles pulling trailers.
View 9 Replies
Fuel injectors do this? They are off a 2006 Ford F350 dually with the 6.0 diesel motor! Have replaced all 8 fuel injectors got back drove for 200miles and fuel injectors 4 and 8 were throwing codes changed them out and high pressure oil pump oil coolant deleted egr valve changed the ipr valve feed tubes to the oil rails. replaced the FICM. Yet again drove for 2 days about 200 miles again and shut down (stalled) misfiring hard start. and now fuel injector 4 is throwing codes again. Have not drove it since we got it home from the last stall out which was a few feet from our drive way and we towed it home.
View 5 Replies
A month ago I got into my truck in the morning and when I turned the key to Run everything lit up like normal and after the glow plugs warmed up, I turned the key and there was about a two second delay between me turning the key and the engine cranking over.
The next couple times I tried starting the truck that same morning I had to try to start it a couple times because it wouldn't try to crank over the first couple times but it would always eventually start.
It's been continuing to give me problems but never stopped running once it was started and then this morning I tried starting it for 45 minutes with no luck.
What I have tried so far is:
Resetting batteries
Jumping the truck
Checked to see if the starter is getting power. ( I put wire testers on it while someone else started and I didn't get a good reading even when it did start. New starter was put in 9 months ago.)
I also made sure wire going to starter wasn't corroded
Battery terminals are also not corroded
Checked fuses
Tried starting truck with fan clutch disconnected
Cussing at it
Tapping starter with a hammer while trying to start it
Also, everything sounds perfectly normal when I turn the key, it just doesn't even try to turn over.
View 7 Replies
I have a 2004 Ford f 350 superduty. Everything runs great. Now the other day my fan came on and stayed on for three days now. It goes with my rpm so when I am doing a 100 down the highway in hopes it will disengage but won't.. Everything is Stalk.
View 3 Replies
My 05 F350 6.0 won't turn over with the key, everything comes on like normal but won't turn over. Starts fine with factory remote start. What to check?
View 3 Replies
I would like the hear what others have to say about the problems I'm having with my 2006 F-350 sd xlt 6.0 with 113,000 miles on it. It's being used as a tool truck mostly going from a shop on the property to close by buildings on the same property. In other words very short distances. Used occasionally to take a dump trailer to a close by dumping ground.
1. White smoke from exhaust. I've read this is most likely an ERG cooler that needs replacing. Any other possible causes? If I end up having to replace the cooler is there a stock cooler that is reliable or should I get the one by bullet proof?
2. Diesel is dripping from the muffler weep hole. Last full tank lasted only 60 miles. Could this be the oil cooler? Anything else? If so is the Ford replacement cooler OK or should I go with an upgraded cooler?
View 14 Replies
So this '06 F350 is blowing fluid from the steering pump fitting when you move steering wheel to either side all the way(lock). Is the internal o-ring blown in the fitting? Do these have the teflon seal at the pump? Pretty new to the 6.0 scene. Got a new line ordered.
View 6 Replies
I have a 06 f350 superduty with a 6.0 I have had injector problems before with the motor even hydro locking no start this is the problem my truck started blowing white smoke with a strong diesel smell everyone said it was oil cooler but I took it to a ford garage the guy said I had 2 injectors hung open and wasn't hydro locking and suggested to put all 8 in so I did 3400.00 not I went to pick it up had no power at all turbo was not kicking in so I took it right back to them they checked it out said turbo was sticking had to clean it it would take 6 hrs. said the fuel In the motor caused it it was working fine when I took it to them now they say maybe a new turbo are they giving me the run around or is this possible....
View 9 Replies
I have a 2006 f350 4x4 dually 6.0. The other morning when leaving for work I hard a loud air noise, like a jet. It only happens when the motor is trying to create boost. I have NO boost. No smoke. If I push the fuel pedal past 1/4, nothing. Its like its stuck and no more power at all. I have changed the boot from the turbo to the intercooler pipe. (looked like it had cracks in it). Checked the cold pipe, no cracks seen. Check the exhaust clamps, into the turbo, they are tight. The turbo is seeping oil around the seal. I took the inlet, fresh air, pipe off. Check the turbo spool for looseness, fins, spun the wheel, ran the engine and watch to wheel. Seen no issues. Where to go now?? No coolant leaks, no oil leaks.
View 7 Replies
My dad recently bought 2006 6.0. He has had it about 2 and half months. Has the egr delete kit installed. The truck has ran great. Up until Wednesday the 3rd. My dad headed to Ut to pick up our new quads. While heading up a small grade with empty trailer in tow. Truck went to limp mode, fan kicked on, orange wrench came on on dash board. He pulled over let her cool down turned her off.
Checked fluids Then started her back up and she was fine. That has happened 3 times. Now he is on his way back (tow haul mode turned on) and it is doing it again. She hasn't went into limp mode yet. As soon as the fan kicks in my dad pulls over immediately and puts it in park. And lets her cool down checks fluids. This issue only happens mid way up a grade. So my question is...... What is causing this? How do we fix her and make her a happy truck again.
View 7 Replies
I drive an 06 f350 with a 6.0 diesel. My truck has quit on me twice in two months. It lost power then stalled and would not restart. I had just changed fuel filters but checked them anyway to see if they were plugged. They looked clean so i put them back in and the truck fired up. It ran good then two months later it did the same thing.
I noticed I could not hear the fuel pump so i pulled the cap off if the top fuel filter to see if there was fuel in it, and heard air being sucked in (or pushed out?) as i loosened the cap. I put the cap back on then turned the key and i could hear the fuel pump working. I waited for glow plugs and it fired up. Is my engine getting vapor locked, or sucking air? If so then why would it only happen every now and then instead of continuously?
View 14 Replies
New to the forums, not new to fords. 1999 F350 7.3L Diesel. This has been a work truck and has seen multiple devices in and out over the years. I removed the last crap for GPS tracking etc from the last owners. The truck has worked well for a long time since until...
I'm moving slowly to a different state and so the truck got parked for 2 months. went to start it and nothing. the dash comes on and all the lights come on but when you turn the key to start the power drops and nothing.
Testing so far:
replaced the fender Solenoid
tested the starter motor and solenoid -passed
replaced the ignition switch
tested continuity of the hot and ground wires to the fender and starter and everything passed
When I shorted across the fender solenoid the starter works and tries to start the truck (unsuccessfully so far)
So the wire that goes to the fender solenoid is not working and where to trace it to and what needs to be fixed. Is there a relay or fuse besides number 30 that is in the way? where does the magical wire go so i can check its continuity?
I am stuck 800 miles from where i need to be and I am stuck here. I don't have the cash to get a mechanic and my mechanic friends are stumped. I do have a Snapon modus tester, what to do with it.
FYI the batteries are new and fully charged.
View 14 Replies
I recently bought an 03 F350. I've noticed on cold starts that it has no power. After about 5 minutes it runs very well. I have not noticed any misfires or smoke and there are no codes thrown. Based on what I have read here, I assumed it was a FICM issue. I just got done testing it and it was at a solid 48v with 1 dip to 46 on engine crank. I'm baffled at this point. The truck literally has no other issues except low power for the first 5 minutes.
View 14 Replies
Don't know where to start so I'll ramble!
2005 f350 with the 6.0. Crew Cab, 8' box, 4x4 with DRW. I use it only take the boat to the launch 5 minutes away once in a while and to pull car trailers every other week. Majority of driving is on the highway and average trip is about 300 miles. Low power and now no start.
No codes. I do have a scan Gauge and can provide data.
Was running this week, but has had a lack of power for some time. I had put 2 new injectors in last summer. Also updated dummy and stand pipes. Blue spring. Also new IPR at the time.
Ficm board was replaced in March.
New injector harness last year. New Glow plug harness last year.
Coolant level is fine and none being lost.
CAC hoses appear fine, no cracks.
No boost. But newer MAP sensor, hose not cracked or plugged and nipple on intake is clear. Put the MAP sensor last year and it didn't make a difference.
Turbo was rebuilt 2 years ago.
IPR has to hit close to 80 before boost hits 12-15. But it takes a while to get there.
Now won't start.
Yesterday am it was about 30 farenheit and no start. Last year would start no problem.
Batteries are fine. tested.
Engine fires within 3 seconds, but doesn't want to run.
ICP is above 500. climbs as I turn over.
Fires only in first few seconds and then nothing while I keep cranking it. it is cranking fast enough though.
Now...I see IPR will hit 84.7% and then 14.8%. Not good!
When running it sits in between.
FICm voltage is 48.5 key one and 47.5 when cranking.
Wondering if possibly IPR screen is plugged? Or would CKS or CPS cause issues? I recall reading about pulling one of them and cleaning rust off of it? Also...should mention, no EGR reading on scan gauge..never was either. I had checked and cleaned egr valve before. it was clean when I pulled it and not sticking.
Intake had been cleaned 2years ago. Also, on occasion, while pulling up hill, I would get power! Black smoke and it would race up a hill like it's supposed. Then it would go back to no power.
Also...if I pull the MAP hose from the intake nipple, should I feel suction from the intake? There doesn't appear to be any air coming or going from the nipple.
View 14 Replies
I have 2005 f350 with 365000 km on it I have it for one year and don't have a problem till last week. I was pulling van on dolly uphill and sadden lost pover, so I stopped and check oil leaks ,transmission .... But everything looks ok in couple minutes start engine and go home (10 km). Change fuel filters trans filter, looked good for 50km and star losing power again and doesn't want start. So I skan and its show me next numbers.
Key on engine off
Ipr-15%
Icp-0psi
Icp-.26v
Ficm main power-47.8
Ficm logistics power-14.5
Ficm sync is good
Engine crank
Ipr-85%
Ficm main power-48.0
Ficm logistics-12.5
Icp- 625psi
Icp-.77v-1v
So what I have to do?
View 9 Replies
