My f350 6.0 has seem to have lost its power, while I was driving home it would only accelerate at one constant speed, and driving up hill it would not accelerate at all, I also noticed an elevated exhaust temperature.. There are no warning lights or dash lights indicating any problem.....
View 8 RepliesOccasionally when I'm driving, I'll accelerate and get a brief loss of power, then it'll pick back up, followed by a puff of white/blue smoke. This usually happens when the oil is over 120*, but not quite to full operating temps. It doesn't happen every time either. Only 3 times in the past week. Otherwise, there is a very faint haze of white smoke that seems to be constant. It is very difficult to see unless against a dark background. Oil level is good, I check it once a week, no rising or lowering levels.
I pulled the EGR yesterday, all good, although a tad dirty. Cleaned up no problem. Haven't had a chance to do a bubble test yet. There are some DTCs, but I can't remember off the top of my head what they were. I'm about to go clean the inside of the truck, so I will pull those and update in a few minutes.
Truck has about 148,500 miles.
Torque Pro lists these codes: C1145, P0299, P0677
I was driving and went to accelerate quickly and had no power, checked the boost gauge and it had very low boost. Continued like this the rest of the drive, all gauges normal, no check engine light, not towing or hot. Got home then next time out it was back to normal.
Someting to be concerned about? Or just a computer hiccup. Truck is '13 with 66k.
So I have a no start on my 6.0. I was driving and went to accelerate and had no power, pulled off of the road and was idling rough, I checked for fuel leaks-none. I put it in drive and engine cut off and wouldn't start again, changed the ICP (threw a code) still nothing, FICM is good, ICP is 950 psi at cranking, IPR is only at 54%. I'm at a loss of what to do next besides looking at the IPR, and I do not have the equipment for a leak test.
View 14 Repliesi just installed a Dash Cam and it needs power all the time. Is there a way to tap into the dome light?
View 2 RepliesWhile driving I went to speed up and heard a bang. I lost all drive. I have no movement in any gear. I got the truck home and looked around. Trans fluid looked and smelled ok. I couldn't move the rear drive shaft by hand with engine in neutral. I drained the transfer case and that fluid looked fine also. What it could be or what else to look for. The truck is a 2006 f350 with 6.0 and 185,000 miles. Up to this point I had no trans issues.
View 14 RepliesI've mentioned in the recent passed a vibration I have and thinking it may be one of my hub bearings. Now I really can't tell if it's that or something else as it feels like powertrain when accelerating but at speed feels like I'm driving on gravel?? The vibration is a tight one if that makes sense..it's bugging me to death.
View 14 RepliesI have a 2004 F-250 with a 6.0 and am having a serious issue. The truck has about 240,000 miles and has been great until now. About a week ago the truck was running great and had plenty of power. I decided to wash it with my pressure washer (did not spray under the hood, however I did spray in the front wheel wells and underneath the truck). About 5 minutes after washing the truck, I took it out for a drive and noticed when I really got on the accelerator the truck would not want to try harder and motor got very quiet. Really all you could hear was the turbo whistling. Over this past week the problem has gradually gotten worse... a few days ago I had to feather the pedal in order to go up hills. If I gave it more than about 1/4 inch of accelerator, the motor once again would get quiet and the truck would start to slow down and would not want to work.
However, if I let up and only gave it a small amount of accelerator, the motor would sound normal again and it would pull up the hill. Today, I can do nothing more than idle back and forth in the driveway because the motor gets quiet and the turbo winds up if you give it even the slightest amount of accelerator. I have no idea if it's a coincidence that this happened after washing the truck, or if maybe there was a sensor that was rotted and about to die and I finished the job with the pressure washer. I already replaced the egr valve and have been running tons of Howes diesel conditioner and anti gel through it. The injectors were replaced about 50,000 miles ago so I'd hate to think it was them. The truck doesn't smoke at all either.
I have a 2005 6.0. I just got done doing the HPOP seals, injector o-rings, stand pipes and dummy plugs. I have drove the truck 600 miles since the work with no problems other than a wiring issue I got fixed...
I was driving at highway speeds, and all of a sudden I lost power and got a shake when trying to accelerate. I pulled over and turned it off, and when I went to restart it I got nothing at first, then it went to what seemed like a partial crank followed by a thud. So I'm thinking I just hydro locked it. I waited a few mins and tried again, and it started but had a few knocks for 15 seconds or so, then it ran rough with smoke pouring out of the exhaust (grey then turned kinda white).
I the only codes I have are for the egr which I've had unplugged for a long time, and a glow plug code, but when I started it back up, I had no codes. I'm baffled. I did notice I have oil on my oil filter housing at the cap, a little oil had slung on to my wire harness and my intake. I don't even know where to begin!
I have a 2006 F250 6.0 Amarillo Edition. 133,000 When I bought the truck it was a theft recovery vehicle where the turbo, injectors, FICM and wiring harness were stolen. The company I bought it from replaced the injectors, wiring harness-new, and a used FICM, and turbo. Also has EGR delete and SCT tuner with basic tunes. I believe the SCT was put on to mask another problem. No dealer would spend that kind of money to sell a truck unless something was wrong. The truck would accelerate some with the tuner but shift the tires so hard it would bark them. I removed the tuner and went back to stock program.
The truck will barely move and takes a long time to accelerate under a load. In park and neutral it is fine. A friend has a ford diagnostic program on his computer and says the readings were all good except EBP was a little high. Removed exhaust and air intake to verify no restrictions. Turbo sounded like the vanes might be sticking so I replaced the turbo and VGT solenoid. Now truck feels like its trying to make more boost but not transferring power to the engine. Have blown the silicone hose off twice now during testing. Checked the EBP sensor and tube and only thing I see is a little carbon buildup inside the sensor. What else to check. I'm new when it comes to diesels.
I have an 03 Excursion with 220,000 on the clock. Started getting harder starts randomly about a month ago, maybe a little more, pulled codes got p2290. Reset everything, changed the oil, oil filter, both fuel filters, eventually the ICP sensor itself and rebuilt the IPR with new screen kit and rings. Hard start went away for about a week but ICP pressure was dropping drastically during hard throttle or even trying to go up a good sized hill. I had a bypass oil filtration kit on and noticed that the connection on top of the oil filter housing was weeping at idle and leaking enough at throttle to possibly cause an issue. Replaced with new OEM filter cap and fill cap, and ended up with a no start and low ICP pressure.
Got it started today after a long crank (15+ seconds), ICP and IPR at idle both warm and cold are mid 600's and low 20's (I can get actuals if needed). After reaching operating temp starts fine after shut off (both immediate and after sitting for 20 minutes). I picked up a selection of parts and tools including an ICP air test tool. Also grabbed a hpop gasket kit and the updated O-rings for the whole system. Live scanning wise I have an Edge CTS and also an SCT x4 that I can use.
Saturday while moving some items for the inlaws my truck, while moving at slow speed, reduced power to the point where it almost stalled, anti lock brakes were growling, right rear tire was dragging the brakes skidding the tire. maybe ten seconds then ran normal. got to stop sign and made a right turn and at about 30 mph started doing the same on and off for maybe 30 seconds. All the time Advance Track light blinking 3 times then pause, and repeating.
Stopped in a parking lot for a couple mins, did not shut off but drove the rest of the way home normally. At home we could smell brakes cooking, right rear brake disk was very hot. Drove to dealer Sunday morn with Advance Track over-ridden and ran normal. What would happen at highway speeds or towing my fiver? Bet they cant reproduce the prob, left no code etc. You know what that means.... I will update later.
Can I safely assume that the constant drip of non-odorous clear liquid from the engine is from the a/c? It comes down pretty heavy from near the front right tire, about one drop per 2 seconds from what I saw.
View 4 RepliesI've got an 2016 F250 Diesel 6.7 PowerStroke, which I bought fresh off the lot, and just got my regular oil change and tire rotation today, thru a local Ford Dealership. I'm working out of town, so I didn't take it to my home dealership as I have been every 5,000 miles since I drive a lot for work. As of today, I'm currently at 47,000 miles. Just to stay on top of things, any time I'm asked to get any type of extra additives, or filters needing to be changed, I do so. I don't like bad surprises when it comes to vehicles. So after getting my truck serviced today, and back to work, I notice a constant "Ticking" but do not know why. Thought maybe after running it all day at work, not literally all day, that it would go away. I took it in at 7:00am, and here I am at 9:30pm, and it still ticking. What it could be?
View 7 RepliesI have a 2005 F-350 Lariat, FX4, CrewCab, with an 8ft Bed if any of that matters. Currently sitting at 191,000 miles and 4,500 Engine Hours I just started running into some issues that I cannot figure out. To start with here is a list of all the mods and prior maintenance that I've done to my truck over that last 6+ years that I've owned it.
I purchased the truck in 2010 and had no issues whatsoever for the first 3 years.....then it all started. While pulling a camper home from vacation "still bone stock" the truck overheated and by the time I realized it it was to late. I ended up blowing a head gasket cracking a head and blowing a hole in my coolant reservoir from the heat & compression of the engine in the coolant system. So to the shop it went.
All of this was done at the same time at just under 4,000 engine hours:
1) Both heads were sent out to be pressure tested "which is where the crack was found", so 1 replacement head and the other trued up and tested by the machine shop
2) All 8 injectors replaced with Airtex/Wells New/Reman
3) ARP Head Studs
4) BPD EGR Cooler
5) New Stock Coolant Reservoir
6) New Stock Oil Cooler
7) Motorcraft Coolant & Oil/Oil Filter Change
8) New Serpentine Belt
After getting the truck back I installed some upgrades that I had wanted but didn't want to do until I had head studs. 4" Turbo back Diamond Eye Performance exhaust, Bully Dog GT Tuner with an EGT Pyro, coolant changed to Caterpillar ELC, Sinister Diesel coolant filtration system, new Optima batteries "I hated them",
Forward a year with no problems I had a crank but no start. I ended up having a bad IPR. A buddy rebuilt the turbo since I had it out and it was leaking. He apparently did something wrong because it took its own life sometime after. So a brand new stock Garrett Turbo with a Wicked Wheel 2 & I changed the IPR "don't remember the brand." Also replaced the factory paper air filter with a cleanable one from AFE that fits in the factory cold air intake.
Little more time and I started to have some overheating issues again, luckily the Bully Dog was monitoring and I had alerts set up so I caught it way before it caused any serious damage. Turned out the fan clutch wasn't working. So I replaced the Water Pump with one from dieselsite.com that has a steel impeller, also replaced the computer controlled fan clutch with a 7.3L mechanical fan clutch and an adapter from BPD.
After that the batteries I hated were replaced. I installed Oddssey Extreme 950CCA ones, a new 185A alternator from FICMRepair.com as well as the complete battery wiring interconnect kit. Did the blue spring upgrade. Replaced my FICM with the BPD 6 phase at 54V setting. Also I changed my starter to an 6.4L Ultima one from O'Reily Auto to bring me up from that slow crank of the 6.0L at about 150RPM to the 225RPM of the 6.4L.
So now on to the current issue. This has happened in the last month and may be related to the issue. I had some small coolant leaks and wanted them fixed. Pressure tested the system & found the radiator and timing cover gasket leaking. I installed a new stock radiator and lower radiator hose. Had the shop do the gasket and a serpentine belt due to cleaners being all over it. During replacement of the timing cover gasket my mechanic found that the LPOP gears had some damage as if something had be in there at one time. Not sever damage just minor. LPOP replaced with brand new one from Ford.
After I got the truck back it was fine for 2 weeks, no leaks or any problems whatsoever. Then I noticed a hesitation as I was leaving work at idle. You could see the RPM's moving up and down by about 50 as it sat there at idle. It got really bad and eventually stalled on me. It fired right back up and ran fine after. I was thinking water in the fuel or just maybe old fuel because it was kinda old and I was at 1/4 of a tank. I went and filled up and it ran great all the way home. Day or so later same thing. At idle you can see the RPM fluctuating and while driving it feels like it has no power at times then it goes away and runs fine. So I changed both fuel filter with Motorcraft ones and put in a new oil filter. It is the Wix brand but I've be running it for years with no issues, one was also in it way before this issues started. The oil has about 2,000 miles on it currently. I verified fuel pressure at idle to be at 70PSI. I tried unplugging the ICP at idle with no change in the hesitation. So I plugged in my SG2 and started to see if I could see anything out of the ordinary.
OAT - 60 Degrees F
KOEO Engine Cold - FMP - 54.5V, ICV - 0.25V, ICP - 0, IPR - 14.9
KOER Engine Warm - FMP - 54.5V, ICV - 0.82V, ICP - 576, IPR - 23.5
Cruise at 40MPH - FMP - 54.5V, ICV - 1.14V, ICP - 965, IPR - 32.9
Cruise at 50MPH - FMP - 54.5V, ICV - 1.42V, ICP - 1,190, IPR - 38.0
Cruise at 60MPH - FMP - 54.5V, ICV - 1.27V, ICP - 1,143, IPR - 37.2
While driving this issue comes and goes very randomly. The only parameter I notice changing alot is the IPR. It jumps around a lot and sometimes it will go to 85. I know that this isn't a good thing so I am going to change the IPR later today or tomorrow. I already had a brand new Motorcraft one to put in, plus at the very least I want to look at the screen. I had read somewhere that there could be air in the oil system and that if you run at a high RPM it can remove this air. I never seen any bubbles or anything on the dipstick. My brother ran the truck for me at 3,000RPM for 5 minutes. No hesitation during the test but he didn't have the SG2 plugged in so I don't know the parameters during the test. I thought that it worked but then it came back after a few miles of driving. The above parameters are from this mornings drive home from work.
My uncle bought an '05 that stopped running one day. He was driving down the road and engine lost power. He was able to coast into his driveway. Unfortunately, it's been 10 years since I've work on a 6.0 and no longer have any of my computers.
He did state there is no check engine light. He's going to change the filters today / tomorrow. I'm hoping to make it down there this weekend to look at it, but what to look for. Even more unfortunately, we really don't have any specialty tools or gauges.
I have searched and the only thing close is bad sensor for water in fuel light but it does not say they lost power. When driving or leaving from a stopped position, if I put any extra load on engine by pressing on accelerator pedal fast the water in fuel light comes on and the glow plug light comes on and the truck loses all power. Not 12V power just engine power. I have to let off the pedal and the lights go out and I have power again. Until I press the pedal hard again and it does it again. I have drained the filters and replaced them and still the same.
View 14 RepliesNewbie hear to the 6.0L's. But I'm learning an awful lot really quick from all of you here. I've read lots of tech stuff on these EGR Coolers, oil coolers, FICM tests. This is what I got happening right now.
2004 F-250 6.0L. Today was 45 degrees in Reno. 5400 ft elevation. Tried to start it without block heater. Would not even crank. It tried to crank but sounded like it locked up on first crank. Tried again, nothing. Same. Tried yet again and finally got to getting the engine to crank, but wouldn't start after about 5 seconds of cranking. Waited a little while not wanting to burn out my FICM, then tried again. Same as previous, would crank but not turnover. Checked batteries. Both were over 12.3 V cold, motor not running. This next time, turned key on and let it sit in ON position for about a minute. Then cranked and it took about 5 seconds and then the motor finally cranked over. Lots of black smoke as usual for a cold start like this. Battery volts after cranking over and running were now both over 13.6 V.
Keep in mind the truck has started better than this before in 15 degree weather just about a month ago.
After it started I noticed what appeared to be oil/coolant residue directly underneath trucks transmission area. It was not tranny, but in that area. I got under the truck and can see this fluid coming from EGR Cooler area.
Now for the smoke. Just stared smoking on start up. White smoke. Then it would disappear as engine warmed up. Now its constant white smoke when warmed up and applying the throttle. Smells like coolant coming out of exhaust. Not diesel.
I parked truck facing downwards on my driveway. Then I checked EGR Valve. When I pulled it it was WET. Not dry. Peeked in EGR Valve hole, didn't see coolant. Just wetness. I did change gasket and rings on it the day before as well.
As for FICM, it reads 47.9 Volts on key turn, 48.1 on cranking and 47.8 running. FICM good by all standard 6.0L literature. Degas bottle passed pressure test holding near 15 PSI for 20 minutes! No oil in degas bottle that I can see.
Truck is stock. Is my egr cooler and oil cooler shot? Would a bad egr cooler or oil cooler cause this awful cold start? When I plug in the block heater, it starts NO PROBLEM, but still white smoke. Also, NO loss of power at any time.
I have an 07 6.0 with 400,000 miles. Has been a great truck with no major problems. Before I started the work I had 3 bad injectors, running rough and the oil/ coolant temp just outside of 15 degrees. So I tour her down and replaced head gaskets, installed arp studs,all new injectors,all new glow plugs and new oil cooler. Ran great for a couple days. Then when driving to work lost power on and off for a few miles then completely gone could only go 10 miles an hour. I checked codes and there was the under boost code witch has been on there for a while and I forget the other code but it was for the ipr valve so I replaced the valve and right after still the same but that code went away and the p0470 popped up. So I cleaned out the ep sensor tube and replaced the valve. After several miles she now runs great but now I'm getting a little puff of white smoke when I take off and not every time and mainly when I take off some what quick. All codes are gone expect the under boost. I have an egr delete already.
View 7 RepliesSo I was driving down highway when I lost power. Engine was still running just had no power and would blow black smoke when I got on the accelerator. I pulled the EGR valve and noticed it had rocks stuck keeping the valve open. Cleaned it all up and put it back in. Went for test drive and seemed good again until few miles in same problem. Took it apart again and same thing.. rocks. I did this 3 times with same results...rocks getting stuck in my valve.
View 1 RepliesSo I have a 06 f350 6.0 and this started to happen yesterday. I was driving and all my temp gauges were ok says the tuner, but I noticed when I accelerated and went above 8psi the noise got significantly louder and wouldn't go above 17psi so the cause of this sound is making lose pressure somewhere.
- I check the hot side of the inner cooler pipe and boots for cracks or tears(nothing)
- I checked the cold side and the plastic seems to be in good shape except where the flex part meets the inner cooler had some little cracks in it
- I check the Intake for cracks, didn't see any.
Noise is still there and the loss of power.....so I'm at a loss!
Cold side pipe where I taped it
Hot side boot to inner cooler no tears
No cracks in hot side pipe
Hot side on turbo
Cold side of the inner cooler