Ford 6.0L Power Stroke Diesel :: 2007 - Power Loss When Driving - White Smoke Blowing
Oct 30, 2015
I have an 07 6.0 with 400,000 miles. Has been a great truck with no major problems. Before I started the work I had 3 bad injectors, running rough and the oil/ coolant temp just outside of 15 degrees. So I tour her down and replaced head gaskets, installed arp studs,all new injectors,all new glow plugs and new oil cooler. Ran great for a couple days. Then when driving to work lost power on and off for a few miles then completely gone could only go 10 miles an hour. I checked codes and there was the under boost code witch has been on there for a while and I forget the other code but it was for the ipr valve so I replaced the valve and right after still the same but that code went away and the p0470 popped up. So I cleaned out the ep sensor tube and replaced the valve. After several miles she now runs great but now I'm getting a little puff of white smoke when I take off and not every time and mainly when I take off some what quick. All codes are gone expect the under boost. I have an egr delete already.
View 7 Replies
Advertisement
I just bought this 2007 F250 a 126K miles on it. Drove it about 1500 miles with no problems. I changed the coolant to Rotella ELC, installed Sinister Diesel Coolant and Oil Filter Bypass, and changed oil to Rotella 15W-40. 3 days after I did this it was in the mid 30's in the morning when I headed to town. It was blowing white smoke, so I stopped and smelled it. It did not smell sweet. I saw what looked liked diluted oil dripping from the exhaust. As I turned around it stopped. I revved it up and no smoke. I headed back into town(around 10 miles) no smoke. Drove home and no smoke. I was at home for about an hour and when I started the truck it was blowing white smoke.
I revved it up a couple times and it went away. I drove about 125 miles and no smoke. I let the truck sit about an hour and when I started it was blowing white smoke and no matter how much I revved the truck it did not go away. I went to work and the truck sat for 3 weeks. I just installed the blue spring kit. Started the truck and no smoke at first. Then, when it went to fast idle a little wisp of white smoke. As soon as I revved the truck up it got worse. Then it blew out what once again looked like diluted oil about 5 feet out the exhaust( I have a huge tractor weight sprayed with this). My first thought was maybe with the thicker oil I am getting some stiction so I am planning to change the oil to 5W-40 and add Hot Shot Secret tomorrow. But blowing the oil like substance out the exhaust has me concerned.
View 3 Replies
I try to turn on my truck today and it will not crank. The day before I had change two injectors and I turned on the truck when two fill up my tank and I put a full bottle of injector cleaner with it. When I drove off, a few blocks down the truck turn off on me. I started to turn on the truck and every time I did it would blow heavy white smoke out the tail pipe and then it would shut off. I did this about 10 times until I decide to call a tow truck. The next day I empty out the fuel tank and fill it with diesel only. I tried to turn on the truck and it would not crank. I ended putting two new batteries and still the same result. What can this be ? 2007 6.0 Diesel ...
View 14 Replies
I picked up a 2003 6.0 awhile back went ahead and did studs,gaskets, delete. Was driving it and seemed to lose power, started coughing and carrying on blowing bluish white smoke then shut off. Ended up hydrlocking #5, Oring on injector was tore when took out. Put all back together, ran horrible, did a balance test with AE, showed #3 injector, replaced, ran horrible, did AE dropped #1 injector. So in process of replacing the rest of the injectors. Just wondering why it is or was dropping them 1 at a time. Ficm was showing 47.6 to 48.6 volts, could that be it?????
View 14 Replies
I have a 2006 F350 6.0 litre diesel. The other day I started it up drove away and it was blowing huge plumes of white smoke out of the exhaust. Shut it off.....started it up again after a while then went on a long drive and it went away. What that was?
View 6 Replies
SO, I've owned a 92 f250 7.3 for 10 years and it's got over 340k miles on it. Well, she is getting tired so I'm debating replacing the truck with a SLIGHTLY newer model.
I've found a truck that is a 99 7.3 powerstroke with a 6 speed manual and 260k miles. Knowing these engines I feel this truck has at least another 100k in it if the thing was somewhat taken care of. The issue is that the fella that has it for sale says it ran great for years and one day started blowing white smoke while driving. Other than this new issue it runs fine.
So my question is, what could be the issues causing the white smoke? I always thought white meant unburned diesel or maybe antifreeze. Head gasket comes to mind but it's not something I've ever dealt with.
I like that he parked it when it started having issues. Sounds like someone who doesn't completely trash their vehicles. Too high given the condition? Truck looks and sounds pretty good aside from the smoke, pretty reasonable condition.
View 13 Replies
2006 blowing white smoke and sluggish until its driven for a few miles ..smells like fuel .. New head gaskets and the works started after 20 days over below freezing temps nights at 5 to -5 ....
View 14 Replies
My 2006 6.0 is blowing white smoke/steam and Im losing coolant (not out the top). Pulled the EGR valve and its wet down there. All signs lead to EGR cooler? I've been reading a lot on this forum and Ill do the oil cooler at the same time. I seems VERY important to flush the coolant system before I tear into this. I am afraid of hydro locking the motor or ruining the head gasket or stretching the head studs if I run the truck. How can I do this without further damaging the engine? I am doing this myself. I'll have 3 solid days to finish this job because I have to tow my trailer in 5 days.
View 5 Replies
My 04 PS was blowin white smoke constantly while running. I just towed a uHaul from Connecticut to Virginia Beach and had some coolant issues on the drive down (I was out of coolant on 95 in PA, added coolant and it made the rest of the drive no problem). I got here to Virginia and it was low on coolant again. I added coolant to it, and now I have some other issues. I had what looked like oil comin out the stacks onto the bed, so I pulled the turbo thinking it was seals. But the turbo was just rebuilt prior to me buying it with a wicked wheel in it. It still had stock EGR and it has 202K on it.
Checked and found EGR valve was wet. Ordered an EGR delete kit, and just finished installing it. Now with everything put back together, the truck doesn't want to start. It cranks but doesn't fire. I pulled the codes from my tuner and I got: P0403, P0405, P0683, and P2623. I know P0403 and P0405 are related to EGR but the others I'm at a loss on. The EGR delete kit I bought included the blank to remove the valve but what do I do with the plug that used to plug into it? Any way forward to get the truck back up and runnin again? This is my daily driver and not lookin to break the bank to get it goin again but I really need her to be reliable.
View 14 Replies
2006 overheats and starts blowing white smoke, smells like antifreeze, added 2 gals of water to make it 1 mile home. Smokes on the way @195 temp and when I shut it off it smokes out tailpipe for another 3 min. Smells like the head gaskets just went, what should I check? The eot and ect have been 10 deg or less.
This has 225,000 miles on it ran great before this, so would it be stupid too not get a redone set of heads while I'm doing the gaskets and studs?
I was thinking of getting heads from here, UCF Machine Shop - Precision machining, engine rebuilding and more. Cummins + Ford Rebuild Specialist. And a Sinister Diesel Complete Solution For Ford Powerstroke 2003-2007 6.0L. Are these the right places to deal with or should I look elsewhere?
View 14 Replies
Well my problem went from bad to worse. My 05 started running rough at idle, then smoothed out a bit but started smoking on acceleration a little. At this point it felt like it had more power than ever before and even ran smoother running up to 3k RPM before shifting (manual transmission). But now it's smoking so bad, I can't really drive it. It's smoking white or gray at idle but blowing black smoke on acceleration. I had a cylinder 5 contribution code but with the amount of smoke it's hard to believe only one injector is a problem. I pulled the EGR valve and it doesn't look stuck open but I'm going to replace it anyway.
View 3 Replies
2007 6.0 6 speed, 187,000 miles. The other day started truck, had been running about 20 minutes before. Started fine, go to drive, chugging white smoke, smelled like unburnt diesel, baby truck home, seemed to run ok at low rpm, truck warmed up and ran fine. But I also noticed turbo boost was acting funny. Truck ran fine next few days. Then this morning, started cold fine, started to drive it and same chugging white smoke, it quit by the time j got to the end of my driveway, but drove to work, it quit smoking, ran pretty smooth, but will not build any boost. Truck is bone stock except for exhaust, it's straight piped. Ok. So this eve I borrowed my dads edge cts, here's all the engine codes:
P0069
P0269
P0299
P2262
P2269
The last one is water in fuel, since it started this crap I did notice it was right after it came on in the dash. I'm trying to figure out where to start....
On another note. VGT duty shows 85% at idle ?
Ficm voltage is constant 48 volts
Newer batteries
View 14 Replies
I'm in the middle of an extended coolant flush and switch over to ELC. As of recently, I have noticed white smoke at startup and driving while cold and warming up. (Even at times accelerating when half warmed up ~170*). At first I attributed it to suction, so last night I changed the oil with T6 along with a new OEM filter.
After I got done with the oil, I pulled my EGR valve when the engine was hot. Is this simply goey due to warmth, or do you suspect EGR cooler leaking? I didn't take pictures of the manifold, but the lower chamber was hard and dry, while the middle section seemed to be "goey". EGR Cooler or something else???
View 6 Replies
My 02 excursion is missing at idle and jars the whole truck around going approx 50mph feels like good amount of power loss but still pushing 30psi boost, just got autoenginuity all injectors buzz fine on the test, contribution test show balance fault in cylinders 1&8, should I look for o-rings to be bad, uvch, cups cracked or what ----- turbo fine, hpop great condition, new IPR, new fuel pump and hutch mod, about. 250k miles on truck nothing else major showed up on ae.
View 5 Replies
I am a mechanic and tow operator running a late 99 f350 7.3 6 speed cab and chassis wrecker. This truck has had a hard life and has been neglected for quite some time, and now has become my baby/headache. Truck starts great, idles nice, and will run great for about 5 minutes until it starts billowing white smoke that smells like fuel and loses all power. If you continue to drive it it will die. Sounds like it's dropping cylinders and will barely idle. If you stop for 5 minutes or so and let it idle it will smooth back out and will run great again for another minute or two, then right back to stumbling.
Using torque app, hpop pressure looks good when it's running well. Peaks at 3k, IPR maintaining 30-40% max. As soon as it stumbles you can see the hpop drop to 5-600 and the IPR will climb to 65%. Let it idea bit and they go back to normal, and stay good until it stumbles again.
Ive changed the fuel pump, ICP,rebuilt FPR, change fuel filter, pulled and cleaned the fuel tank (metal tank, no delamination, looks perfect inside). Pickup screen looked good. Cleaned the IPR, cleaned the hpop reservoir, there was no screen inside. Checked voltage at fuel pump, 11.78 across the pump with it running. Pulled valve covers, no noticeable leaks around injectors. Injectors have less than 5k miles. Remans with 100% larger tips.
To me it seems like the lpop is not keeping up with the hpop under load, starving it until you idle and let it catch up. Could it still be bad injector orings? Bad lpop? Something I'm not thinking of?
View 7 Replies
I have a 2001 F450 7.3 chassis cab with just over 100k. I have a new problem... So far on two different occasions the service engine came on followed by a loss of power under a load and white smoke from the exhaust. Took it to the shop the first time, they determined it to be a dirty air filter, which seemed odd since it just happened all of a sudden. They changed air & fuel filter, problem gone- for two weeks..
View 8 Replies
Moving my worldly goods from California to Oklahoma in a rented 26' box truck with my wife following in our '02 F350 loaded to the gills with my lathe, mill, air compressor, weld and assorted machinery. Just west of Deming NM it started to blow lots of white smoke and down on power. Some rattling noises from the engine when throttled up & won't reach 3000RPM.
Had it towed to an impound yard for storage. Plan on sending a flat bed to pick it up when we get to Tulsa.
Any experience with a tilt back trailer capable of loading & transporting this truck that weighs around 17,000 pounds? My plan is to continue on to Tulsa & make arrangements from there.
View 14 Replies
I bought a 2004 power stroke with 100k miles, ran well for 15k miles then started having low power for first few minutes to no power, regular oil changes and fuel filters at 5k, checked FICM 48v KOEO , 48v cranking, new batteries just in case. Oil pressure when cranking at 50% of gauge , even crank cycle will jump when trying to fire, no loss of coolant, block heater working, it did start a few a few times and blew white smoke until warm then full power but the last 2 times I did get it to start it ran for less than 1 minute and died could not restart.
Fresh fuel additive in both fuel and oil for stickshion, have read hundreds of posts but not seeing similar problems no codes. With key cycle 120 amp draw on passengers battery for approx 25 seconds 48 amp on right battery glow plugs good due to the amp draw? So I think my FICM is good, good oil pressure cranking, the oil pump should be good, ICP good? Because of gauge coming up? Everything I read says black smoke for EGR soot issues. Not sure where to look.
View 14 Replies
it's now 1,500 miles away on the side of the road.White smoke, knocking and lost power. Truck has 133,000 reman engine installed at 46,000. Is it common for hydro locking to bend a rod? He sent a video and it def sounds like a rod and degas is empty.
View 9 Replies
I went out to the store today all was fine came back out and started driving got 2 miles down the road to a red light and the truck about stalled no power it doesn't smoke at idle but revved up it blows black and some white and the truck shakes. I am thinking its stiction or bad FICM????
View 13 Replies
I just looked back and it has been since July 7th that my girl has been sitting in my shop. Well this past weekend I finally got her back together and started. It took a while to build pressure but she finally came to life..
While I am thrilled that she is running again i have low power before the boost kicks in and is idling rough with a blueish- white smoke coming out of the exhaust. Once i kick her a little she will get up and go but I've never had the smoke before.
I'm thinking maybe a bad injector???
View 3 Replies
