Ford 6.0L Power Stroke Diesel :: Overdrive Stumble / Truck Barely Idling When Come To A Stop
Mar 30, 2015
So from what I have gathered online, it is an injector(s) issue. I've only had it happen to me twice at that speed but when I came to a stop afterward, my truck was barely idling.
I'm not sure if my sct programmer is able to show injector codes but it will show gp codes. I guess my question is are failing injectors that intermittent typically? Also, much luck with Rev X clearing that issue up?
View 2 Replies
Advertisement
My 6.0 with 178k on it just started to have issues today. Low power. When I hit the pedal hard the motor revs and the truck barley moves. When I baby it it goes up to speed and shifts fine. Overall lacking power and not going anywhere. No CEL on. Turbo spools and seems to be ok.
View 5 Replies
I have a 2006 F250 6.0 Amarillo Edition. 133,000 When I bought the truck it was a theft recovery vehicle where the turbo, injectors, FICM and wiring harness were stolen. The company I bought it from replaced the injectors, wiring harness-new, and a used FICM, and turbo. Also has EGR delete and SCT tuner with basic tunes. I believe the SCT was put on to mask another problem. No dealer would spend that kind of money to sell a truck unless something was wrong. The truck would accelerate some with the tuner but shift the tires so hard it would bark them. I removed the tuner and went back to stock program.
The truck will barely move and takes a long time to accelerate under a load. In park and neutral it is fine. A friend has a ford diagnostic program on his computer and says the readings were all good except EBP was a little high. Removed exhaust and air intake to verify no restrictions. Turbo sounded like the vanes might be sticking so I replaced the turbo and VGT solenoid. Now truck feels like its trying to make more boost but not transferring power to the engine. Have blown the silicone hose off twice now during testing. Checked the EBP sensor and tube and only thing I see is a little carbon buildup inside the sensor. What else to check. I'm new when it comes to diesels.
View 6 Replies
Wtf is going on, Temps are all good, no check engine codes...bad diesel fuel? I had 1/4 tank of diesel fuel when I filled it up...
View 14 Replies
This morning I went to go to the corner to buy something, I knew it was colder than usual, -12F. I did not plug in the pre-heater last night. I let the truck idle for 15 minutes before moving it. It was still idling high. The P0087 code is the only code popping- is this just because of the cold temp? I haven't owned a diesel since my '79 Rabbitt, and this engine is as different from that as night is day. this didn't happen yesterday but it only got down to -2F and warmed up to about 18F.
View 6 Replies
Yesterday, my truck began to shut off abruptly. Under every condition, from idling to slow running (30mph), and 70 mph, to load and no load. Wait 1 minute and it would start and run for 1 minute 15 seconds. If the batteries were disconnected, the truck would run for 13 minutes before shutting off. Have replaced the fuel filters. Still does it, but runs for between 10 and 20 minutes before shutting off.
Am seeing only two errors codes. P1000, and P0603. I was 40 miles into the Ville Vidal, when this started, and 150 miles from home. To get home, I disconnected the batteries too many times to count, and bled the HFCM numerous times. Am also seeing the moisture in fuel icon on teh dash light up when it quits, but so far as I can tell there is no moisture in the separate.
2003 F450 6.0, automatic. 150K miles.
View 14 Replies
My 05 has Glowshift gauges on the window pillar. All are analog except the digital fuel pressure gauge. It almost always reads 102 and that can't be right. Sometimes when idling at a stop light it might go down to 95 for a few seconds. Maybe wire grounding out from sensor?
View 8 Replies
My 2012 f250 is been acting weird, usually the truck is boosting while on gear when I'm at a stop (around 0.40) I think that's normal on a 6.7 because it's always done it, but since yesterday I noticed it sounds different and it's not on boost anymore it just vacuums while on gear at a stop (around -0.25) I'm thinking it's the wastegate solenoid but I'm not 100% sure, and the truck doesn't boost as fast as before but it drives fine and I'm actually getting better gas mileage since it doesn't boost as before, what it could be? It's tuned and deleted....
View 7 Replies
Problem started 2 days ago, driving around and my truck would stumble and lose power. Give it gas, won't rev up but it cleared and ran fine for a mile or so then it comes back (off and on all the way home). Check engine light didn't come on the first few times, came on a couple times on the way home (maybe 4 mile trip) but goes off when the truck runs fine. Thinking it was maybe the fuel pump (got 140K on the stocker). Talked to a few friends, some thought it was algae build up in the tank that was clogging the filter on the pump, underhood filter changed a couple hundred miles ago. Looked fine with slight brown build up at bottom of bowl when I replaced it.
Ran it around yesterday with a friend of mine and his scan tool hooked up, acted up once, check engine came on for a few seconds and shutoff. No code and for some reason we couldn't get it to live data while driving. I dumped in an algae eater yesterday and left the truck overnight since I had to work. Got home this morning to run her around the block to circulate the eater. Truck started and idled fine, went to pull out and she won't rev up, pumped the gas and NOTHING! Check engine light is on now but don't have a scan tool handy to read it. I heard the truck will store the code?
What this problem might be? What's a good scan tool for our trucks that can live data as well? CPS is good and already did the UVCH mod.
View 14 Replies
So about 3 days ago I made a long 9 hour drive. No problems at all but I did allow my fuel to get a little lower then I normally do. About eighth a tank had 30 miles left on the digital read out. Stopped and filled up at loves where I always get my fuel. And off I went drove it down to 3/4 a tank and made it to my stopping point. Got in to go about 7 miles down the road and come to a stop sign and slowing down the truck died. I thought crap I forgot to turn off the auto start but never done that before. Stopped and stared truck as normal. Made it to my stopping point again. Headed back to the house and doing on average 55mph and truck surges like it wants to die but doesn't.
Rpms drop below 500 and it keeps going I get to same stop sign and slowing down again doing maybe 25ish and truck dies again as I have my foot on the break. Put in nut and started it right up and drive on home. Today went about same distance. Only this time I started it with key and was doing down other things while letting it run it just dies start it back up and take off get to where I was going and it surged or hiccuped so to say. Again started it once I was getting ready to leave and let it run for about 5 min and it died had the heater on as it was chilly out by the lake. Got in and restarted it and it was blowing cold air and had a diesel smell to it. Wife asked me if truck was going to blow up. Backed out of area and put in drive and made it 80' or so and truck died again doing about 10mph
Checked so far
Batteries checked and both are good
No mods done to it
New ICP sensor and pigtail
New water pump
New injectors 20k miles ago
Oil changed 1100 miles ago
New filters upper sad lower
2003 Ford F-250 King Ranch 6.0
View 5 Replies
I was driving down the interstate with cruise set at 75 an my truck jerked twice an my cruise cut off. I tried to rest it but it wouldn't. Then I noticed my speedometer wasn't working. Truck will still crank an drive but acts like it has no power an will only at up to 16 psi of boost.
View 13 Replies
Luckily I was sitting in the driveway. Pulled the truck out of the garage. It started fine, idled fine, did not make as much noise as I was expecting but was warmer in the garage than outside. Stopped in front of the garage door to grab a couple things in the garage, jumped back in and it quit before I could get it in gear and roll out. Weird. This is the first time I've ever had to get a tow.
View 14 Replies
I have a 2005 Ford F-250 Powerstroke. At times when stopping at light or for any reason, I give it gas but it does not want to go. It's like it is not even registering that I am pushing the pedal. I shift it into neutral and rev it up then switch it back to drive and it goes and puffs out smoke. What is going on?
View 6 Replies
So I have had this occasional hiccup that has gotten more frequent. I figured since our weather has been extra cold (lows about 15 F, around 22 F in the morning), that the temperature had been contributing to the issue. My truck would hiccup and burp out some white smoke. At first it didn't throw a check engine or any codes. As of recently I would get a check engine light, but torque pro could not get any codes, they would be cleared when I cycled the key. Anyways, I finally got some codes yesterday because it happened again. The codes where P0603 and P0344.
So I ordered 2 new CPS from Riffraff yesterday (hoping that they will be here today so I can install one). Fast forward to this morning and i get the hiccup again except worse. Now my truck would barely reach 20mph and it constantly bucked. I limped my way to work (only 4 miles) and of course I got a check engine light but there were no codes that I could retrieve with Torque Pro again. I had read on another thread that the guy had an issue with a wire in the harness near the 42pin connector for the IDM. He replaced his CPS taped up the wire and it went away.
I'm at work and now I'm paranoid that I wont be able to make it home. Is there anything temporary I can do for the CPS, like maybe disconnect it and spray it with some contact cleaner, until I can replace it? I'm going to trace the wire harness to make sure there aren't any bare wires. I forgot to mention that the local stealership replaced the CPS for free due to recall less than 3000 miles ago...
View 5 Replies
I was driving home tonight and stopped at stop sign. I took off and truck died and coasted to a stop. I tried to start but all it does is theft light blinks really fast and will not turn motor over. I tried to reset pat by following procedure I found on internet. Still no start. I then unhooked battery cables and left off for 15 minutes then hooked up but still no start and blinking theft light. I also tried spare key and still no start. What else can I do. I had it towed to place that just bulletproof my truck. Truck has been running great. I did not want to leave it on the side off road in the middle of country all night.
View 3 Replies
How does one clear the computer to prevent the display "Check Coolant Additive" from appearing every time I start the truck. I know that a chemical test is needed to determine the status of the coolant.
View 2 Replies
Finally got everything buttoned up, and truck was going for it's first drive today. Started cranking, and it just barely tries to start, and then nothing until I cycle the key again. Doesn't even give me a full Vroom, Just like a Vro- and then back to cranking.
I've had it started and running a few times, so something has changed. And to add to the fun, something between my tablet, my torque pro app, and my dongle isn't playing nice. Tablet just won't see the dongle. So I get to figure that out too.
View 14 Replies
I just bought a 2004 F350 6.0 cclb 6 speed with 260k on it. The previous owner seemed to have taken good care of the truck. It is basically stock with the exception of the blue spring mod, and a sinister diesel coolant filter. Anyways, I brought the truck home and it ran great. Now I have an issue that needs to be addressed.
The issue: I am experiencing a intermittent loss of power, stall, or stumble when engine is cold. After sitting all night the truck will start fine and idle fine. But when I try to accelerate and bring engine RPM up the engine will stumble and lose all throttle response, when this happens the WTS and WIF light flash. Sometimes it just stumbles, sometimes the truck will actually die and then restart. The issue seems to go away after the engine has reached operating temp.
I did some research on the issue and it seems there is actually a TSB out from ford for this issue. It explains that some 2003-2004 6.0's might have wiring harness chaffing issues. This is what the issue I am having seems like to me (shorting harness). I looked up codes on the truck and there is an active code (#8 glow plug circuit fault). I did a short visual inspection of harness and didn't see anything out of the ordinary. But i wonder if it would be worth changing both sides of the glow plug harness?
View 2 Replies
I have a 2004 f350 6.0 it has 73000 miles on it. I've had the truck for about a month and its developed a slight stumble, hesitation. It does it during idle and acceleration, if I give it more throttle it smooths out. The cel is not on and there are no stored codes.It did this a few days after i bought it,i noticed the map sensor was broke in half so i replaced that and it smoothed out.But it came back. Exhaust is clean no white or black smoke at all.
View 11 Replies
I have a 2006 F-250 4x4 with no cat, and no egr but the valve is still connected. It has about 146,000 miles. Just recently when warm, it has a slight miss every once and a while when stopped and in gear. Just a slight drop in RPM then recovery. Its mainly used on the highway and 99% of the time I set the cruise and its smooth as silk. Every once and a while I feel it stumble once or twice, recover and it is fine for the next 80 miles with no issue. It started as once every few trips but now It seems to be happening at least once every other. I use Motorcraft filters (maybe 6K on the fuel filters) and rotella oil. My scangaugeII shows no codes and no Injector pressure issue (1200-1400 at 75 mph depending on grade) and the FICM voltage stays between 48.5v and 49.0V. What should I check?
View 2 Replies
First... Items I have replaced:
- New EGR valve
- New sensor
- New Fuel filters
- New Oil filter
Problem:
While driving I have a stumble along with a small amount of black smoke at this time ( was white/bluish smoke ) previous. I have dis-connected the batteries to force the computer to relearn the EGR valve. The turbo spools up .. getting about 20 psi @ hard throttle and then about 5 psi after it goes into the final drive gear. Speaking of which ... the stumble is always worst on the final drive gear...
View 14 Replies
