Ford 6.0L Power Stroke Diesel :: Sluggish Offline When Warm?
Feb 7, 2015
So after I've been driving for a while and stop at a light or drive thru, I will give it throttle and it seems like it wants to stall. Almost like the turbo isn't spooling and then does and all is good again. Is this a sticking turbo bearing or something else? I am not very familiar with this motor(although I have been doing a ton of searching on here) as I just got it about two weeks ago. I should mention that I am getting the 404 and 405 codes so not sure if that could be involved with the egr?
View 9 Replies
Advertisement
What is a "normal" number people see on their load factor? Mine was around 25-30 a few weeks ago but I noticed it is increasing to around 30-40 once I'm in gear, in park it's fine. My acceleration is also getting a bit sluggish too especially going up hills and my throttle isn't responding all the way, my turbo boost is normal though and I don't think there is any VGT stiction. I'm thinking either a fuel filter or a MAF sensor to start with. Fuel filters have been in exactly 10 months. Can a dirty fuel filter, air filter, or MAF sensor affect engine load at idle and how fast it accelerates? I feel like I'm pulling a trailer and with it being more sluggish, my transmission is shifting harder as well.
View 14 Replies
When I first start it in the morning and go to take off, It runs sluggish and doesn't smoothen out for the first 1/2 to 1 mile. It then seems to run fine. I have no clue as to what to start checking. The temperature was 65 degrees out, so I don't think that was a factor. I don't know if it's and fuel problem or trans issue, or what. I'm clueless at the moment. It had a recent oil change and fuel filter(s) change. Was doing it before then. 2004 F-250 Super Duty CC 6.0
View 8 Replies
Can a bad or lazy VGT solenoid cause a P132B code? I just recently had the turbo cleaned and the VGT solenoid replaced about 3 months ago. The truck is a bit sluggish at take off. Is there anyway to check the solenoid to see if its bad?
View 14 Replies
I've come to the conclusion that after 300,000 miles my turbo is sticking. I need to drive the truck up to my mechanic but he's 50 miles away 90% highway (really don't wanna pay the towing bill) would this hurt the truck any more or would it be okay? If it will hurt the truck more I'll get it towed but I'm trying to avoid that at all costs. I have drove it since the turbo began to stick but it is very sluggish and smokes a lot. As soon as I let off the pedal boost immediately drops to 0 psi.
View 3 Replies
I have researched this online and it seems everyone leans towards a custom tune after this upgrade? It ran like a raped ape before the old stock turbo took a crap!
View 2 Replies
Started today. 2004 with 235k miles. Owned for last 10k miles. Engine was recently studded, has egr delete and ccv bypass. Runs and starts fine. New Ford oil cooler too. Checked for codes. None for misfires, perdel are reading 0.
If it sits, on start up clear exhaust, as it warms, more blue smoke. Smells like oil not diesel.
Researched before asking and found leaking turbo seals can cause this. So we pulled the intercooler tube in front of the engine going to the intake expecting to find oil residue. Nice and dry. Was this the correct one to look at?
When we got the truck we had the dealer do a relative compression test and was within limits, it did need 1 injector that we replaced. What would be the next logical place to look?
Couple more points:
- Just changed oil last week, checked today, it was slightly over full.
- Coolant is fresh and has not changed level since we got it.
- Pulled fuel filter to see if any oil, but it was nice and clean.
View 11 Replies
2003 f250 6.0.... recently did oil cooler,hpop,ipr,icp,fuel pump,egr valve, rebuilt the turbo.... when around 35mph truck seems sluggish and doesnt seem to pick up quick untill i floor it an then hauls butt.. vgt reading at idle is 62% and when floored around 30 to 35%.. fuel pressure is 63psi.. ipr is around 60 to 70% when floored and around 25% at idle. Hpop reading when floored is 3000 to 4000psi and idle is 624psi....
View 14 Replies
I have a 2011 F250 6.7 that I bought in August of 2010. I have 35K miles on it and it has pretty much been trouble free once I got the firmware update for the shifting issues. I have the local dealership do all of my service work and all updates and service bulletins have been applied. Unfortunately on my way to work this morning the stupid Check Engine Light came on. The dealership has it now - hopefully I will know tomorrow.... I do think it has been running a little sluggish but I am not sure if that is the winter grade diesel (I use PM22-A in every single tank).
View 2 Replies
Driving back from Baseball tonight, I stepped on the throttle truck was sluggish and a huge black trail out the exhaust. On and off the throttle a few times and no more smoke.
Checked codes when we got home and had p132b. I had this a month ago, replaced the map sensor and no issues. So am I looking at a turbo cleaning? Besides the unison ring, is there a seal and bearing kit? I am at 205k at this point and as far as I know the turbo is untouched.
View 7 Replies
Well it's that time of year to start using my air conditioning. Went to use it today and it is blowing nothing but warm air. Worked perfectly last time I used it last year. I thought about buying that 134a ac recharge kit from auto zone.
View 14 Replies
According to the scan gauge... I used to run about 195-200* all the time no matter what.
Now days i find myself up into the 220s and with my boat on ill see 235 climbing a hill.
Good deltas between the water/oil temps.
I wanna get back to my 200's.
I pressure washed out (on low) the front radiator and all the coolers, I didn't get much out and they didn't look dirty.
I am thinking water pump or plugged radiator?
View 14 Replies
Say I just purchased an 06 f250 crew cab with the 6.0.
I had her trailered home due to dead batteries. I got her started up and drove about 5 miles until she got up to operating temp.
When I came to a stop and tried to accelerate, she immediately bogged down and started studdering with white smoke coming from the exhaust.
I shut her down and started her up again. She started and idled fine, but as soon as I pressed on the accelerator, she bogged and studdered again. I shut it down again and started it back up. Normal idle, and I shifted her into gear and was able to mozy on idling forward without having her bog, but as soon as I touch the accelerator, she bogs and studders.
I towed it home and the next day (today) she started just fine and I shifted her into drive and moved it forward about 10 feet. Did not touch the accelerator so she didn't big or studder.
1. I am guessing the white smoke was coolant burning through a failed EGR circuit. Do you seasoned members agree?
2. It the a check engine code when studdering. I have yet to check codes so I am still in diagnosis mode.
3. I plan to block off the EGR pipe and throw in a new oil cooler. Anything else immediate I should be considering??
View 14 Replies
Left on hunting trip last Thurs. Blew tire on trailer 6 miles from home. Shut off truck. Went to restart, cranks only. No codes. Towed home.
Thought it might be a fuel filter problem. Had just changed oil/filter and fuel filters prior to trip. Checked filters, upper bowl was low. Turned key to on and bowl filled up. Noticed filter wasn't snapped in lid. Also checked lower filter.
Drove it to work this am. Turned off truck and tried to restart to check. NO START-Cranks fine!!!
View 14 Replies
my 2006 6.0 will roll over 300,000 miles this week but today I was pulling a 24' pontoon boat that should only weigh a few thousand pounds from hot springs Ar where there are some small rolling hills and the outside temp was 70 degrees. I was driving between 55-60 most of the drive. On a few of the longer hills my eot got up to 220 with the eot trying to catch up.
On the down side it would fall to 185-190 and the eot would also follow. On about a 5 mile straight stretch the ect was 208 and eot 202. When I got home I opened the hood and I do have coolant puke around the degas bottle. After opening the cap there seemed to be a steam/smoke coming out of the degas bottle. There was still some coolant in the bottom but not a whole lot.
On my drive to work every day my delta is between 6-8 degrees with the ect between 188-194 depending on ambient temp. So does this sound like my head gaskets finally let go? Will them blowing raise the eot/ect when towing?
View 14 Replies
I just got this new truck with work and when I started in the mornings and let it run for 10 to 15 minutes like I used to with the 6.2 f250 I had it's still cold in the truck. Need making this thing warm up faster?
View 14 Replies
It takes about 10 minutes for the truck to drive normal. If I start the truck and sit for 5 minutes, then start driving... the truck has a very hard time changing gears and accelerating. Just trying to see if this is normal or not ?
View 14 Replies
Just replaced the hpop on my 04' 6.0. It had been down for about a year because my low pressure oil light would come on after warm up. Truck ran PERFECT, but dam light would come on. Eventually it wouldn't start by cranking, but would on a bump. (I have a 6spd.) still ran good. I would never run it over 5 minutes because i didn't want to damage anything. Finally getting around to fix it.
After a day of air testing, we tracked it down to hpop. (air coming out of turbo drain tube). I had a hunch that the dam bb on pump had spit out from similar stories on FTE, and thats what happened.
Replaced pump. (its an older style pump BTW, although i have a january 04 build and every ford parts guy said differently.) Put everything back together and now it runs terrible! We ran the truck for over 20 minutes and it didn't get better. I am afraid its gonna damage something to keep running it. My mechanic says 5 cylinders are misfiring and its something to do with the ficm or injector harness.... But, it ran perfect right before the hpop change???? Everything was double checked to make sure it wasn't something dumb.
View 13 Replies
Just went on a trip to SC. It was hot as hell - 100F most of the trip. The a/c would blow cool (not exactly cold) for a while and then go luke warm (way better than outside but not particularly refreshing) for a while. So I was reasonably comfortable but definitely not cold.
This would happen about every 15-30min where I felt like the compressor had stopped working for a while. I am thinking the compressor is probably limping along and about to die. Usually I thought these things just up and die though. Clogged accumulator? IDK - nothing has been done to the a/c system since 2009 head gaskets.
View 14 Replies
I have recently developed this problem with my 2005 F250 6.0L with 86,000 miles and don't quite understand it. If I drive my truck and then shut it off for a couple minutes, say to go in the store for a few things, when I try to start it back up it won't stay running. It chugs for a couple seconds at real low RPMs (300-400) then just stalls. When I was at the store the first time this happened, I went back in and bought a bottle of starting fluid and gave it a shot, (I know I know, shouldn't do that) and it started right up and got me home.
Thought it was a fluke as the next time I went to start it, it fired right up (sat over night). Drove a couple hours then shut it off, it sat for three or four hours. I went to fire it up to go to a wedding shower down the street about 20 minutes drive and it started fine. Shut it off to go in and pay my "respects" and was out in ten to fifteen minutes. Again Chug, Chug, Chug, stall. Tried to start it with the same results about ten times, then I said fine went back in and ate some free food and drinks for a couple hours and came back out and it fired right up again.
I drove home tonight and while in by drive way at home tonight I verified this again. Turned the truck off and tried to start it back up ten minutes after unloading the truck and same thing, no start. What could be the problem? Only other issue I've noticed was a lack of power on take off from a dead stop then a like a switch the power comes on in about three seconds.
View 14 Replies
How can I tell if the turbo is going? it has a whirl noise after warm up. Boost seems a little slow and seem to have more noise coming from the air filter inlet. I put the Auto Enginuity on and have no codes.
View 7 Replies
