Ford 6.0L Power Stroke Diesel :: Truck Will Start Running Really Rough After Filling Gas Then It Will Clear Up
Sep 8, 2017
I have an 04 F2 50 with 6.0 with approximately 225,000 miles. I filled up with gas last Wednesday and every so often the truck will start running really rough and then it will clear up. Is it possible to of gotten some bad gas if so what products are out there to clear that up. Could've been injector going bad what are the best products for cleaning injectors. No check engine light on, gauges are good, nothing different on the scan gauge.
View 3 Replies
Advertisement
This has me puzzled to no end. After my son had put fuel in my truck it began to run rough, and had to be towed home, and now won't start. Now the first thing I thought was that he put regular gas in. But he was sure he had not ,and the receipt from the pump indicates diesel. It was hard starting before this happened.
1st Misfortune of having gas put in instead of diesel and did your vehicle run afterwards.
2nd Here are my readings from my scangage:
Sync Yes/1, Ficm main power 48.5 v, ICV .17 (2.01 when cranking). ICP 1572. IPR 50.7.
Checked upper fuel filter for bubbles, none.
Engine oil pressure comes up immediately on cranking.
Don't know what else to check, these readings look fine to me. Only the fuel is something I'm not 100% sure of. It does smell like diesel not gasoline.
View 14 Replies
Today the truck struggled to start after filling up, even harder the next time, and now it's in my driveway dead and I have a job at work that requires me to go to Michigan next week that I can't afford to lose. On to the issue...
When cranking, my icp won't go above 400psi now, and I understand I need Atleast 500 to fire off. I'm mechanically inclined but new to diesels, so don't be afraid to dumb it down...can't be cocky when your learning. Where should I start my troubleshooting?
View 14 Replies
My Excursion got 4 new injectors a couple weeks ago and when I got it back, it was running rough. My mechanic told me it was going to take about 100 miles for them to break in.
300 miles later and it is still running rough. So I opened the hood, took a look around and saw this wiring harness unplugged. Where it goes? Youtube video shows where the harness is [URL] ......
Also, my truck has been shaking violently at 50 miles per hour, unless I hit tow haul, then it is moved up to 60... I am assuming its connected some how to that wiring harness being disconnected.
View 14 Replies
My truck was running rough when cold, I went to check the ficm voltage while wife was cranking and coolant shot right into the ficm and cooked the sumbitch. Stop laughing that stuff happens to me all the time. Anyhow, got a new ficm and truck wont start. Starter kicks out after a few revs. I ran my own solenoid wire to the starter and it cranks just fine. ficm at 48.5 koeo and cranking, icp 1100+, ipr from 14.8 to around 40%, ...
It takes a few seconds for the cam/crank to sync but it does. I changed the fuel filters and primed it, Got new batteries, and threw a crank sensor for s+g. With the key on and me cranking it using the solenoid wire, it almost starts. But from the key it will kick out after a few seconds. All fuses and relays are good. I hear the pcm also controls the starter, could that have cooked when the ficm went or would it blow a fuse? Diagnosing using a scangauge2 ....
View 14 Replies
So I have been fighting a rough running, missing problem. My truck started running rough one day on the way home. I got it scanned, it showed injector contribution balance 1&2. Made sense to me that it threw those codes. I replaced 1 and 2 with oem replacements. Got that all done, truck still ran like crap. I changed fuel filter with motorcraft ones and drained the water separator. That didn't work. I am getting it scanned again, so i will have codes shortly.
Also, for a while it would run with absolute no problem. It was intermittent like that. Run bad run bad run bad and then one day run flawlessly. I though it was electrical. Checked all the common places for chaffing, saw nothing. Even did the wiggle test while it was running, no change. But it hasn't been intermittent for a while now.
View 14 Replies
Since our weather has returned to the cold side......my truck has started bucking and hesitating at 45 mph with EOT @ 130 and ECT @ 140. I can gas on it and it will clear up/let off and it would start up again once it gets below 50 mph. Once the deltas reach 150+ it clears up completely. Its never done this until this week. FICM volts are steady @ 48V. What is causing this or what to look for?
View 2 Replies
2004 F550 with a 6.0. I had to clean out my fuel tank, replace the HFCM and filter on top of the engine. When I start the truck it will run for 30 seconds or so, start running rough then die. I opened the cap on the fuel filter housing on top of the engine to make sure the fuel was getting there. I turned the key on and the fuel bowl quickly filled up.
After a short time however, the fuel drained out. To where I do not know. I don't think this is normal as every time I've changed the upper filter on a 6.0 it is always full of fuel. Why could this one be draining out and could that be the issue why the truck dies after starting and running for a short period of time. I changed the o-ring on the cap and the new HFCM was purchased from Ford.
View 13 Replies
Well it finally happened, a couple of weeks ago I was headed to an MX race and my check engine light came on and it started running rough. Long story short a piece of an exhaust valve broke off and went out through the head. Dealer has been great even though I was 300 miles from home and they did get me a rental(small POS SUV). Truck was supposed to be finished this week, but now they are saying the head gasket is on back order and they probably won't have one until the middle of April......... I can't be without my truck that long, but not much I can do. By the way truck is completely stock with just under 20K on it, and I have never had any issues with any of my Ford trucks or Ford diesels, even my old 6.0.
View 7 Replies
Well, I've read a lot of threads on this problem! Try to do my own repairs, so I'm learning and not spending a lot of cash at repair shops.I have an 04 6.0 Super Duty Crew. Starting running rough on way home. Pulled over ,then it died.wouldn't start. Had towed home. Replaced ficm circuit board. No start. Replaced Harness,
icp...... ipr Sensors. Still no start. I noticed there is another circuit board inside ficm. Should I have bought the whole ficm unit?
View 4 Replies
Last friday, my truck died while running. I let it sit for a few hours, went out and it started right up. Went to get pizza for my kids and I got 5 blocks from my house and I barely had any power. Truck died again while getting pizza and had to tow it home. Now it will not start. I have checked fuses, taken apart the fuel pump on the motor and cleaned the water from it, added a fuel treatment and also did an old truckers trick with the fuel (10% gasoline). the truck will crank and make an attempt to fire but it will not start. I have 3 kids and this is my ONLY transportation. I need to get this thing running STAT.
View 1 Replies
I was towing a trailer about 600 miles truck was running great, pulled in for fuel and truck was running rough, refueled and was on my way then when going down a hill (Idle) it just quit, had to tow remaining 200 miles.
After reading the forums I replaced the ICR (ICR screen was damaged) Truck now starts but its very loud and missing like crazy. and surges if i give it a little gas. codes 0268, 0281, 2284, 2288 I also replaced the ICP.
should I replace the injectors? what causes this?
View 14 Replies
I just bought a 2007 6.0 with 239k miles on the truck, it has EGR delete and ARP head studs. When i bought it the owner warned me of injector stiction...
I drove the truck for about a week, changed the oil over to Rotella T6 with archoil, and swapped out the air filter so far. (previously was non synthetic rotella). I drove the truck 2 more times since changing those two items and then i had a no start issue.
Scanguage2 said it was FICM sync.....so i messed with the wire loom, and got it to start twice but it died right away. (it had ficm sync, then it died and went back to 0) So i ordered a CPS pigtail and was going to change it out today.
Today i went out and pushed on the CPS sensor directly, charged both batteries and the truck started rough but kept running after two times (still haven't changed the pig tail)
Now it starts but is still running rough.
Scangauge 2 Running:
IPR : 23.8
ICP : 581
FICM SYC : 1
FMP : 48.5
The only code i'm getting is P0269 which I'm hoping is only injector 3, a bad injector wouldn't cause all this would it?
I'm just trying to figure out what i should look at next.
View 5 Replies
I had an HPOP line burst and soak the engine compartment with oil. I replaced the line and degreased the engine and rinsed it off. I started the truck and let it idle for 15 minutes or so before driving it. On the way home right after a shift it started chugging and running terribly. The check engine light was on as well. I limped it the mile or so home and shut it off. I restarted it and it runs just fine. I checked the DTC's with Forscan and there were a bunch of things that were mostly related to the HPOP and the MAT sensor that was shredded when the line blew. I left the hood open to dry out today and I'm hoping it is just some water in a connector. Does that sound plausible?
View 6 Replies
Wtf is going on, Temps are all good, no check engine codes...bad diesel fuel? I had 1/4 tank of diesel fuel when I filled it up...
View 14 Replies
I have a 2001 F350, 7.3. My service engine light came on and immediately the truck started to run rough and lose some power. I've checked the under the cover connections and they were both connected, I replaced the cam position sensor and I still have the same problem. The worse part of the hold thing is that there are no codes stored so I'm flying bind. Where to go next.
View 8 Replies
Finally, you can get EGT's with the Torque app!
I had to reinstall Torque on my new phone and EGT1 was in the predefined set of PID's for Ford. Launch Torque, the go to Settings, Manage extra PIDs/Sensors, Menu, Add perdifined set, select "Ford (Incl PowerStroke)". I believe it's getting data from EGT11 that is between the turbo and the DOC.
I included a graph that shows the truck running empty at 50-55 MPH, ambient air temp. ~50F and the EGT's are around 430F, at 60-65. They are 480-500F. If one of guys/gals with the Edge Insight/H&S/other tuner would be kind enough to confirm those numbers are correct.
This was on a 2 lane highway following a couple of old rock haulers, then I passed 'em.
View 12 Replies
Strange thing happened yesterday and again today. I have my compressor hooked up to up fitter #3 ,turned it on yesterday to fill the tank back up to 120psi. Before it filled up i shut the truck off to fuel up..but the compressor kept running for a few seconds after the truck was off. and today doing some running around the compressor turned on out of the blue when i was driving..but the switch was off.
The shut off switch (on the compressor itself) turns it on at around 90psi and shuts off at 120, but the thing filled my tank to 180 before i noticed it was on, pulled over to shut the truck off and again it ran for 10-15 seconds after the truck was off. I'm pretty confused. maybe it has something to do with the build up of snow under the truck, we just got 16" two days ago. but still when the up fitter is off shouldn't that cut the power from the accessory hooked up to it?
View 9 Replies
I am having a problem with a 6.7. The truck has 9900 miles on it. It has a dpf delete, egr delete, Spartan tuner and a snow stage 3 kit. The truck lopes at idle but once throttle is applied it levels out but still runs a little rough. Its keeps saying its in reduce engine power no matter how many times I clear the code. If I clear the code it will come back in 2 seconds with out cranking the truck or anything. Rail pressure is telling me 31090 psi and not changing running or not. I have changed rail pressure sensor, and pressure control valve with no result. The green and violet 5 volt reference that feeds those sensors is only putting out 1.2 volts. Put a new pcm in it still the same and now has quit running totally. The codes are P0193, P0335,and P06A6.
View 14 Replies
I got a 2005 f350 6.0 deleted and studded with air dog 2 4g pump, 125k miles. It started running rough then just died all within a few miles tuner showed code for injector 6 and ficm towed into ford dealer didnt have time to mess with it. They said ficm was bad had them replaced it then they said i need whole new fuel system lines,harness,pump,sending unit ,tank the whole 9 yrds. Which i thought was uncalled for so i called up airdog which system i had on there and they laughed and said ford garage is full of bs that they will upgrade my pump to the 4g and new harness.
So I took that stuff to garage had them swap it out and now they said come get the truck they wont work on it anymore that now it needs 3 injectors and they wont touch it with aftermarket fuel system on it. So I go to drive it home and it starts but runs rough and u can hold it to the floor and it wont budge bearly idles up and builds no boost my tuner is showing injector 2,3,4 now which wasn't a problem before i took it into the garage. So im not sure what happened to cause this all to happen but before i sink any more money into it is the 3 injectors enough cause to make it not build boost now .
View 7 Replies
Did my oil change last night and filter swapped both fuel filters on my 04 f350 started it up last night drove it a little bit and she was fine. Went to start her up this morning and she was pissy so I drove her a bit once warm and she feels like there is a dead cylinder maybe??
View 8 Replies
