Ford 7.3L Power Stroke (1999-2003) :: 2001 F250 Cranked Fine But Would Not Fire
May 6, 2015
Owning a 2001 F250 Extended cab with a 7.3 I have not had a lot of questions to ask fortunately.
My truck has spent a lot more time sitting than running lately and when I went to start it the other day it cranked fine but would not fire. Quick read on this forum and the first thing I found was how if the fuel solenoid had less than 10.8 volts when cranking it would not start.
I went down and checked the battery voltage and it was at 12.1 volts no load. I put the battery charger on for about 10 hours (time to kill) and when I pulled the charger and cranked it over, started with no problem.
View 3 Replies
Advertisement
My dad has a 99 F250 with a no start issue. Everything was starting and running fine one day. The next he gets a no start. Cranks fast and fine but wont fire up and start. He has a scangaugeII hooked up to it and his oil pressures and volts look fine. His tach moves when he is trying to start it. He checked the icp sensor and it had oil through it so he replaced it with a Ford part. Unplugged it and the scangauge pressure goes up but no start. He also replaced the ipr with a new Ford one just in case. He checked and is getting low pressure and high pressure oil.
I am having him check the fuel heater fuse #22 to make sure it is not blown. He had the block heater plugged in all night along with a battery charger to make sure they are topped off as well. We have gone through a couple of the checklists on this site for a no start condition but nothing has solved it yet. I think he is sitting at about 200k on the motor. No major issues or problems until now. He is currently also pulling the ICM to check it out as well. No codes are being thrown.
View 14 Replies
My dad has a 99 F250 with a no start issue. Everything was starting and running fine one day. The next he gets a no start. Cranks fast and fine but wont fire up and start. He has a scangaugeII hooked up to it and his oil pressures and volts look fine. His tach moves when he is trying to start it. He checked the icp sensor and it had oil through it so he replaced it with a Ford part. Unplugged it and the scangauge pressure goes up but no start. He also replaced the ipr with a new Ford one just in case. He checked and is getting low pressure and high pressure oil. I am having him check the fuel heater fuse #22 to make sure it is not blown. He had the block heater plugged in all night along with a battery charger to make sure they are topped off as well. We have gone through a couple of the checklists on this site for a no start condition but nothing has solved it yet. If you need any info off the scangauge let me know and I will post the exact readings. I think he is sitting at about 200k on the motor. No major issues or problems until now. He is currently also pulling the ICM to check it out as well. No codes are being thrown.
View 6 Replies
Truck is a e99 f250sd 4x4 7.3 manual trans. The truck started and ran fine to work this morning. Went to leave this afternoon. Hopped in, put key in and tried to start it. Engine just turned over, never started. Thought that it didn't start because I didn't let the plow plugs warm up enough. Turned ignition off, turned back on and let wait to start light to go out. Same thing happened again. Just turned over but wouldn't start. As far as I can tell the fuel pump is running. Felt it vibrating while the ignition was on. What to check.
View 14 Replies
My f250 is having a stalling issue. It will run fine for about 5-10 minutes and then die out, already replaced CPS, fuel filter, and fuel pump. What else could be the problem?
View 4 Replies
I have a 1995 f-250 7.3 liter diesel engine. Truck starts fine and runs good for a while and then it will stall. I pull over and after a couple of attempts it will start and run fine for a while. I have changed the fuel filter and put fresh fuel in but it still stalls.
View 7 Replies
1999 F250 SD V10 I recently replaced the in-tank fuel pump and filter. I operated the truck briefly after and everything was normal. I parked it with about 1/4 tank of new fuel and put it on a battery tender. It was parked in a garage on level ground in temperate weather(Southern Calif.). Two months later I tried to start it and it acted like it did when the fuel pump was bad. Cranked fine but no hint of starting. Could it be the fuel lines have become full of air and need purging through Schrader valve ? I haven't begun to troubleshoot but what to check other than pushing the fuel relay reset button.
View 5 Replies
So I've had my 2003 F-250 power stroke 6.0 for over a year now and replaced the oil with AMS oil which is good for 50,000 miles to a year as well as the oil filter which is guaranteed the same thing. I've only put 5,000 miles on it since I've owned it and made sure to let the engine heat up before going anywhere as well. Recently my engine bogged down and then had problems starting I was able to limp the last 2 miles to work but haven't been able to get it running since.
I replaced the camshaft position sensor and it fired up but once it was running it the rpm gauge dropped below 1000 RPMs it would stall out. Before it didn't have any smoke coming from the engine compartment however now when it starts it does. Is this because there's oil the possibly leaked onto something or fuel? What do I or should I look at to get it fixed?
View 6 Replies
I recently caught up on some maintenance with my truck, changed the turbo pedestal seals, replaced both batteries, brakes, e-brake cable etc and installed new 10k hid headlights. its a single cab 250 with a 7.3 and zf6 4x4 with 133k. a couple days ago I turned on the headlights and the truck died, restarted no problem and would die the next 5 times I tried to turn them on, then it worked fine. yesterday I got in my truck to leave for work and got no wait to start light, no glow plug chatter, no fuel pump running. turns over just fine but no fire.
I got a ride to work and tried it when I got home, fired right up. I pulled the pCM, checked it out, no weird smells and my TS chip wasn't corroded or anything like that, worked fine. drove to 711 to get a 6 pack and it did the headlight thing again. I removed the HIDs because this all started after I installed them and reinstalled my silvanias and it didn't die when I turned them on. this morning went to leave for work, same no start condition. I disconnected both batteries for 30 seconds to reset anything and same problem. I was about ready to light it on fire this morning.
View 1 Replies
A lady friend of mine got a '99 7.3 CCLB auto dually in a divorce. She doesn't drive it but starts it once a week and yesterday it wouldn't start. It cranked about 10/15sec (after waiting for WTS light to go out) before it sputtered and tried to start but it quit. Then it cranked another 10sec or so and the batteries died. It was about 85deg so it should have started w/o GPs.
Watching the voltmeter, GPs seemed to draw current. There's a lot of corrosion on both batteries so I know that needs to be cleaned up. Assuming the batteries aren't shot, after cleaning the corrosion, is it safe to hook jumper cables to a car to charge the batteries, but disconnect the jumper cables before starting the truck? Or should I use a plug in AC charger? I've never jumped a dual battery vehicle - not even my own 7.3.
She wants to sell it but it's in pretty rough condition - possibly normal for that age with 160K on a work truck. It was used in a business she had with her ex. The valley of death has some wet fuel in it and there is a film of diesel on the fuel bowl, fuel lines and wiring in the vicinity. I could smell the fuel before I opened the hood or tried to start it and it hadn't been run in a week. She says it runs fine and uses no oil but is always rough to start. It rolls rather than barks to life. It's bone stock with flat factory downpipe and airbox.
The engine cover is missing. Connectors and wiring on top of the valve covers appear new. She looked up the value and says it books for $7200 on KBB in its current condition. It was always parked in the sun here in Albuquerque and it shows. Body looks good as far as no rust or dents, but the white paint is faded (flat looking) and the blue interior is also pretty rough with 40/20/40 front seat and cracked dash. If I get it running I'll post it in the for sale section if she doesn't find a local buyer by then.
View 4 Replies
Friends truck, 06 with 135k. Problem he's having is, truck cranks over fine but doesn't fire, if he kick starts it, it fires right up. Haven't had the chance to put my AE on it, figured I throw it out there.
View 7 Replies
Got up yesterday and the truck would start. Turns over just fine, but won't fire. Checked codes and got p0403, p0404, and p0405; all egr related issues.
I'm going to pull the egr and clean it, but my question is, would these codes cause a no start? I haven't had any issues with performance that I read are normally happening when people get these codes. Just wondering if I may have another issue along with the egr problems.
View 11 Replies
I have a 01 f-250 7.3 6 speed. I bought the truck a few days ago and the 4x4 wasn't working the dealer replaced the transfer case motor. I have another 01 f-250 that i have been switching parts out of to see if that makes a differences and found nothing to work. Ive switched the switch on the dash out and nothing. Ive switched the two relays under the hood and nothing. I have also checked all fuses. and the connectors on the transfer case.
So I finally popped the covers off the two relays and squeezed them with my fingers and boom transfer case locked into 4lo and then i can squeezed the other and boom back in 2h! So now I'm lost, I know the wiring from the relays to the transfer case is good and the switch is good and relays are good so I'm at a loss.. Also cruise control isn't working idk if that could be related i don't think it is but idk?
View 8 Replies
The fan clutch will come in and out rapidly when NOT in OD and pulling hills with the fifth-wheel attached. Replaced with a new aftermarket fan, then a new OE one. Then had the radiator pulled and all the bugs, etc. blown out. The condition has not changed at all. The original fan clutch was pretty sloppy. There are no codes, the trans fluid is nicely red, the engine does not overheat or even change temp when pulling hills. No check engine light ever. The truck is a 2001 F250 4 X 4 automatic extra cab with 7.3 engine without any modifications and runs perfect except for this. There are about 95k miles on odo. When we use overdrive on the flats, there is no issue.
View 12 Replies
I have 2001 7.3 f250 ... I just got it about 2 months ago I drove it for maybe 2 week and it ran good the other morning I went out to start it and would not start and the way I was parked my low fuel light was on so I put 5 gallons of fuel in finally got it started sum how drove it for maybe 2 hrs parked it and wen we got back in to go it was done for hasn't started since its been down for a bout 2 weeks now I've replaced hpop, icp, pcm, fuel filter,checked idm for corrosion it all looks well, gpr,checked uvch on driver side looked good and changed cps what else do I have to go from ? No matter what it won't start good batteries cranks good but no start ...
View 14 Replies
01 f250. Just bought from my brother. 140000 miles. Immaculate. Truck will die for no reason. Running down the highway, or sitting at a red light. Fires back up. Sometimes have to crank a few times. He has had at a mechanic and everything checks out good. Since birth its only had royal purple that he has changed every 5000 miles as well as all filters. Where do I start?
View 6 Replies
2001 f250 7.3 with 210,000 miles. Was running rough when cold and glow plugs were bad so I bought new glow plugs and had injectors rebuilt with 100% over stock nozzles. When I changed them I made sure I turned the motor with glow plugs out and pulled the drain plug in the head. Wanted to start it just to get the oil out before I let it sit for a few days til I got the tuner. It started fine and I let it run while I ran in the house and when I came back out about 1 min later it was off. Didn't want to start again. Just left it til I got the tuner on and It still doesn't want to start. What I should check? Turns over good and has good batteries. Also it's a hydra chip tuner with beans tunes. Darren weeks rebuilt the injectors.
View 7 Replies
So I have a 2001 f250 7.3l and on my way to work yesterday while driving down a hill I switched my ts 6 switch to 140 and it immediately stalled, so I pulled over and restarted the truck and it started up fine and I drove the rest of the way to work, I go to start it after work and it won't start, it just cranks and cranks and cranks, occasionally it'll fire and I got it to start and was able to rev it for about 30 seconds but then it died, disconnect the 6 position switch from the idm and tried but still nothing.
So today I replaced the ipr valve, got everything back together still won't start maybe a little worse now, I know it's getting fuel cause there's pressure in the bowl when I try to take it off, there's a new icp valve, cps, new fuel filter and new sending unit, the hpop is topped off. Also I noticed when I went to change the ipr the wires on the plug were bare and touching so I addressed that, I don't know what else it could be?
View 14 Replies
I have a 2001 f250 7.3 and I had started to notice I wasn't making as much boost I thought I should have been. I looked around and found a tear in the cold side CAC boot. My question is what is the best option for replacing it, something like RiffRaff or oem? Also should I look at replacing all the boots or just the two up top?
View 14 Replies
I have a 2003 F250 7.3 auto 4x4 SD ... has done 616000kms and is getting a bit rattily and injectors are getting tired . Have found a 2001 7.3 engine that has 130000 miles on clock . Will the 2001 engine fit into my truck .... e.g.. bell housing and crank bolt spacing's, mounts for all the bolt on bits ... is it quicker to take engine and box out or just engine ?? have even read on here that body removal is necessary .have a forklift and workshop available
View 2 Replies
2001 F250 7.3 - warn manual hubs.. However, the wife has been driving the truck and I don't know how often she has cycled 4WD.
Basically if you choose 4WD hi it doesn't light up to indicate that it has engaged, if you drive for a couple of minutes slowly then eventually it drops in - not much use if you're already stuck. It will then select 4Lo. Coming out of 4Lo to 4Hi or 2WD is painfully slow - like 5-6 minutes before the dash light goes out for 2WD.
I was thinking maybe the electric motor for the transfer case - unless it is the transfer case dying.
View 10 Replies
