Ford 7.3L Power Stroke (1999-2003) :: 2002 - Idled Rough After 2 Minutes Then Stalled Now Won't Start?
Oct 3, 2015
So I went out this morning to start the truck up like I do every morning. It cranked once, and didn't start, which is somewhat normal. second crank it started right up, which is normal, then after about 2 minutes, it seemed like the rpms were bouncing and the engine got a little more slower and louder, then it dipped below 500, then stalled. After that moment nothing. It just cranks. Now it was VERY low on fuel, I've been this low on fuel and never had anything like this happen, so my neighbor took me up to the station and I bought 2 gallons. came back, still nada. I went out after letting it sit on the block heater for about an hour and noticed a small puddle of fuel under the truck on the passenger side. I went to start it and the fuel gauge went up to a half tank. cranked, no start. then again and it went up again but slowly started creeping back down.
Now the kicker, I have very limited knowledge of diesel engines, or gas for that matter. So if my intuition is right, this is probably going to be a learning experience for me... what should I check first guys? Its plugged in right now but I am sure that's not gonna fix it.. I am gonna change the oil first since it needs it, I bought shell rotella triple t 15w40 which im assuming is ok. last winter It was leaking fuel when it was really cold out but that was it, just leaking a bit and then after spring it went away. I know I should have fixed it when it started but I have an extreme anxiety to letting any mechanic near my vehicles and just about as much anxiety trying to fix it myself. I'm at a loss for what to do, I'm a pro with computers but this truck scares the crap out of me, I'm terrified I'll do something worse.
2002 Ford F250 Powerstroke 7.3 4x4, 218,000 Miles....
View 14 Replies
Advertisement
I have a 2000 4x4 Limited 7.3 Powerstroke. 290k miles and runs like a top. However, if I don't plug it in for a few hours before starting she sounds like an old John Deere Poppin' Johnny. I had the glow plugs replaced yet had to go back to the repair shop three times since because it threw a code each time. No codes now just rough shaking and vibrating start for about 5min (without plugging in block heater) or so then once warmed up she runs great.
View 7 Replies
Did my starter yesterday. Today now several times, truck ran rough and stalled. Turned over, tach not bumping, no codes. Would go after a couple tries. Stuffed a new CPS into it. Drive 30 miles, now has a noticable miss, no codes, no smoke and quit again, but started right up.
No codes. Does not feel like another truck and under valve cover gaskets.
1999 7.3 Super duty!
View 14 Replies
I have had my excursion for almost 4 years, I love this truck. but lately we have been having issues that we haven't been able to figure out. First it has about 390K miles on it.
I ALWAYS have to plug it in. it could be 90 degrees out and I still have to plug it in. if it Is plugged in normally it will start fine. but then when I go to drive it, it wont have any power until I get like 2 miles down the road. you can push the pedal all the way down and it will go like 10mph. but once it warms up its fine. if I forget to plug it in, I will have to plug it in for about 2 hours and then it will start hard and run really rough for about 10 min. And it will blow greyish smoke out the exhaust.
But now I'm having the issue of keeping it running. it will start and run for 5-15 min and then quit and I have to wait anywhere from 10min - 1 hour to start it again.
View 2 Replies
My f250 is having a stalling issue. It will run fine for about 5-10 minutes and then die out, already replaced CPS, fuel filter, and fuel pump. What else could be the problem?
View 4 Replies
I was towing a trailer about 600 miles truck was running great, pulled in for fuel and truck was running rough, refueled and was on my way then when going down a hill (Idle) it just quit, had to tow remaining 200 miles.
After reading the forums I replaced the ICR (ICR screen was damaged) Truck now starts but its very loud and missing like crazy. and surges if i give it a little gas. codes 0268, 0281, 2284, 2288 I also replaced the ICP.
should I replace the injectors? what causes this?
View 14 Replies
I have a 2002 F-250 7.3, 159k on it. I bought it in March, ran AWESOME up till now. I was driving to work last week, check engine light came on, truck lost power and started idling rough. I have a buddy who works for a Ford dealer as a diesel mechanic, he came over with his scanner and laptop. #2,#4,#8 cylinders kept coming up saying possible problems are injectors, harness, rings.. He also did an electrical check, that all checked out. He told me to get injectors, so I got 4 injectors (yes I got the correct #8 injector), valve cover gasket, injector harness and 4 glow plugs.
The parts came last Friday, we did the job and it ran great. Drove it Friday night, Saturday, Sunday morning, no issues. Sunday afternoon we were on our way to a birthday party, truck started doing the exact same thing... Check engine light, rough idle, loss of power. After I got home from the party, my buddy came back over, put it on the scanner again, getting the same codes again. Deleted the codes, ran the tests again, same codes, deleted the codes, rant the tests again, same codes.
He said he is going to come by tomorrow with the box to check each individual cylinder.
View 14 Replies
2002 F250 7.3L suddenly idling and running very rough, and doesn't have any power. Truck has been running perfect, it's my daily driver, and just put a couple hundred miles on it yesterday with no problems. I had been having some transmission issues when I tow heavy so I bought a new transmission yesterday. This morning I pulled the truck into my garage to change the transmission. Again truck ran fine, no signs of any issues before the trans swap. I changed out the transmission, which included unhooking the trans wiring harness from all the various sensors, and unbolting the starter.
I didn't mess with anything in the engine bay except for unhooking the batteries. I had also repaired the overdrive button wires, as they had been pinched in the steering column and the button wasn't working. When I got everything hooked back up I cranked it up to get the trans fluid flowing through the transmission, it started right up and idled good. I had it running for a few minutes and it was beginning to make a little more noise than usual. When I started to back out of the garage it was getting pretty rough, almost like it was running out of diesel. I put it in neutral and gave it some throttle and noticed I was getting white smoke out of the exhaust and could smell diesel pretty strong.
I checked my injector resistance at the valve covers and got around 4 ohms +/- on all of the injectors. I rechecked all of the clips and harness that I had messed with. I took a look at the ICP sensor and it has oil in the connector which I know can cause a rough running condition in some cases. It looks like it has had oil on it for a while. I unhooked the batteries again for about 20 minutes to try and reset anything that may have messed up. I checked a bunch of connections under the hood to see if anything was unhooked or loose.
I also cleaned up the connector on the ICP sensor. I started the truck back up and it idled perfect so I pulled it back out of the garage and headed down the driveway. It almost immediately started running rough again and barely had the power to go up a small hill. I pulled back in and tried unplugging the ICP while it was running, which made a slight difference in the idle but still very rough. I plugged it back in and the idle progressively got worse until it was chugging really bad. I shut it off after that and haven't messed with it again.
What might have happened? Could it be a bad sensor or transmission position sensor in the new trans? Is it just coincidence that this happened with a transmission swap? I am going to get a new ICP, but if there is anything else I can try/check before I can pick up the ICP on Monday let me know.
View 1 Replies
I have a 2002 F350 4wd with the 7.3. I was driving the truck and all of a sudden it was running like crap. the engine light was on. after a minute or so the engine light goes off and the truck is running fine. then again starts running like crap. I am close to the house so I limp it home. runs like crap.... will barley climb small hills. engine light is on. get home turn it off... next day... starts up and runs great for 10 - 15 min. engine light comes back on... runs like crap.... my neighbor says "It's the crank position sensor" I replace it.... runs great for a month.... now it's doing the same thing......
View 9 Replies
On my 7.3 super cab, I changed the fuel filter last Friday and now on cold start the service engine soon light comes on for a couple minutes (approximately) on a cold start. No other issues. Tried scanning with my scan gauge 2 and no codes. (of coarse I think that thing is a joke for scanning). Not sure if this means anything, but last week before I changed the filter I thought I smelled diesel fuel on a couple different occasions. If I actually did it may not even be related.
View 2 Replies
I have my 2002 Ford F250 Powerstroke. 175,000 original miles by me and only me. SCT, MBRP, Howes or Stanandyne almost always. Runs like new. It starts rough if I don't plug it in. Even on 50 degree days. Then it levels off and runs perfectly. If I plug the truck in I can drive off immediately with perfect operation of motor. I just went 1500 miles. Pulling a car hauler with car. NP at all.
New Glow Plugs, GPR "Yes it works", IPR, New Harness, Buzz Test shows it's fine, New #8 injector last year, New O rings HPOP. My buddy who is a PStroke guy said this trucks runs too perfect for it to be injectors. He recommends seals for the injectors. What does this mean. Or what else can it be. Where should I start.
View 9 Replies
I bought this truck a few months ago. After trying everything under the sun to try and rectify a poor running problem, it was realized that injectors needed replacing. Ended up putting in 160cc/30% unlimited diesel performance injectors. The truck has a rough idle and surging problem. After trying to install the chip from gearhead, the truck didn't run any different, ultimately (according to the shop doing the install) smoking the ECU. New stock ECU, same problem. Goes good under throttle, just idle is bad. I get weird looks at the gas station. People think it has a big cam.
7.3 Rough Idle - YouTube...
View 14 Replies
Here's what I'm dealing with. Took the truck on a 1500 mile trip with no issues. Got home and started it the next morning and it started right up. 1/2 mile from home it starts to run rough and wants to die. It does this for a few minutes and then perks back up and runs fine for however long the trip is. It will always re fire and have no issues. Every morning it's the same game as described above. Within 1/2 from home it's doing this. Seems to be fuel delivery related, but why would it start after sitting overnight, and then after its little fit, run without an issue?
No codes in computer.
View 7 Replies
7.3 auto, starts and idles OKAY, drives fine if you have a light foot but trying to go faster than 50mph or more than 2000 rpm and the whole thing has an anxiety attack. Starts sputtering and popping, lots of grey smoke when it runs rough rough, let off the throttle and it MIGHT behave nicely again.
New lift pump, cleaned the pickup tube, fuel bowl fills nice and fast, just had my edge attitude juice tuner removed since it was causing similar issues that went away for the last 2 months, changed my IPR and CPS (had a mechanic test everything when the tuner was taken out, all injectors buzzed good, sensors good)
When this first happened after the initial problem with the tuner was resolved, it did throw the CEL, but I have since been able to get it to come back on, and my buddies OBD2 scanner wasn't even registering my truck when I hooked up... Dare I say PCM is to blame?
View 14 Replies
I just started having a cold start problem with my '02 Excursion this fall and I'm at my wit's end trying to fix it. Truck starts fine above about 45 degrees and when it's warm. If I plug in the block heater it also starts fine in the cold. If it's not too cold I can eventually get it started by continuing to crank it. It blows white smoke while cranking and for a few seconds after it finally turns over. Smells like fuel. Runs rough for 30 sec after starting when it finally turns over. Definitely seems like glow plugs aren't working. This truck started no problem on GPs alone without plugging in down to -20 deg F before this year.
I started by cleaning all battery connections, including the two ground posts on the engine block, I replaced one bad battery (diagnosed by Autozone; other one was OK), I checked the resistance of the glow plugs (only a few years old with about 30k miles on them) through the connectors on the GP control module (all were about 1 ohm), and confirmed 12V at the power pins in the GP control module connectors. I then replaced the GP control module and the problem is still present. Battery voltage drops from about 12.6 V before I start the GP cycle to about 12V when I turn the key to "ON" and the GP light comes on. How much should the voltage drop when the GPs are on? What the heck else could be wrong??
View 14 Replies
My 99 250, 7.3 is having some strange issues as of lately. When I start it in the morning, when the engine has fully cooled down, it starts right up, then it throws the "wait to start light" runs real rough and just shuts off. Run the glow plugs a few times, start it up and it will do the same thing for maximum 30 minutes, then all the sudden I start it and it runs fine. I've replaced the fuel pump, cleaned the fuel bowl, new fuel filter, I just don't know where my problem could be. It doesn't make sense. But once I get it running and it warms up, runs fine all day. Go to bed, wake up, has problems again.
View 14 Replies
I am intrigued by this engine and it's cold start issues so I am trying things out to see what works. If I plug it in it starts like summertime. If it's as cold as 30* out I run the glow plugs for two minutes and it starts without much effort and once running purrs like a kitten, no chug a lug, no romping, little smoke. When it gets down into the 20's I run the glow plugs for two two minute cycles, a little more cranking time but starts same as above. Down to 18* and I cycle the glow plugs twice for two minutes and it cranks, tries to start but won't. Key off, back on for two more minutes and it starts right up like a warm summer day. It hasn't been colder than 18* here this year so this is the end of my report for now. I haven't taken the time to check the glow plugs which is on my list but this summer it'll get done.
View 14 Replies
I have an issue with my 7.3.... the truck will not start if it sits overnight without being plugged in, even in 65 degree weather. It starts and runs with a rough idle for about 10 seconds after its been plugged in for an hour, after the rough idle is gone it runs great .. it will Stat back up as long as the truck is warm (70+).... I've replaced the batteries, glow plugs, starter (it was going bad) and fuel filter. .. also replaced the gpr today. ....
View 14 Replies
So this is reason #345 why I should never have let my wife drive my F-350. I am in the Army, and I got a frantic call from my wife (I missed the first 7) saying that the truck died and won't start. I drive all the way to the truck, pop the hood and discover:
1) there is no coolant; and
2) there is no oil (actually just EXTREMELY low on both).
So, I do what any good Soldier does, I push the truck all the way back home (downhill mostly), buy 5 quarts of oil and a jug of 50/50 coolant, fill up both and try to start the engine.
The last time it ran out of oil (small leak on a seal that I didn't know about) in 2006, all I had to do was fill the oil, turn the key, and press the gas until it kicked over (don't judge me, I was a dumb LT). I did this again this time (now, I am a dumb CPT) but now it: 1) idles very rough; and 2) won't start unless I press down on the gas when I turn the key. There is no gauge light when it does this. I read the thread on the UVCH, but I am concerned I might have done something horrible to my truck.
2003 Ford F-350 7.3L
View 6 Replies
My 2003 7.3 f250 has trouble starting whenever the temperature is less than 65 degrees. If it is less than 50 degrees I have to plug it in for it to start. Once it starts it runs rough. I let it warm up and it still runs rough. Once I start down the road I'll get on it a bit and it takes off like something lets loose. It then runs geat for the rest of the day but does seem to still crank a little more than it should when I restart it through out the day.
The pickup has 152000k
List of repairs I have done to the truck:
-new gpr
-new glow plugs
-new uvch both sides
-new valve cover gaskets
-new blue cps
-new fuel filter
-new batteries everstart maxx 65n
The truck has an afe air intake, straight exhaust, and a super chips tuner set on mileage saving. It blows white smoke when first started but clears up pretty quick.
View 13 Replies
While headed back to town my 2000 f350 7.3 with 444,650 miles (I'm original owner) and have performed maintenance and repairs since mile 3. Truck started to loose power and eventually stalled, was able to restart several times to limp home 7 miles in one hell of a snow storm. Very confused, replaced cam position sensor ( keep one in jockey box ) replaced fuel filter truck starts then stalls out. Don't know if a bad HPOP would allow start up at all. Fuel pump???
View 6 Replies
