Looking for a write-up on replacing the seals on the hose that leaks at the power steering pump? I replace them once but may of over tightened them. I pour in atf and see it dripping on drivers side of power steering pump. Can I just use regular o rings?
View 5 RepliesHad a lot to do yesterday and had stock trailer hooked up and loaded with debris.
Got 120 miles away, stopped and got the groan from hydroboost/p/s system.
The hose from the pump to the hydroboost was leaking but it was the actual seal on the fitting that gave up rather than the rubber.
Could not find the seal but luckily the Irish place had the line in stock for a reasonable place.
Transmission got hot too backing up and puked out the front seal. I was doing a lot of twisting to get the trailer in the hole.
My high pressure power steering hose just blew at the "B" nut at the pump. Meaning, the fitting is still in the pump but the line is out. Do I need to replace the whole line or is there a retainer I can swap out?
View 14 RepliesIs there one thing that when broken makes both the steering and brakes lose all power? Does the power steering and hydroboost share a pressure source?
My brake pedal is dead and I get no steering boost, but the master cylinder and PSP are full of fluid. Do I replace both, or replace one first to see if that fixes both? Or could it just be a hose leaking? Not sure how to diagnose this one.
So, I'm replacing the Steering Box today and read an article that said you should replace the pump at the same time. what do you all think?? I have clear access to it now and they are not all that expensive?? Or are the ford one's bullet proof and leave it alone???
I don't have any leaks and it feels ok I guess..just pushing close to 200K on it.
I have a 2000 Excursion. This weekend, I noticed some intermittent failure of the power steering where it seemed like the pump was not engaging and then would all of the sudden. Deciding to try to head off a failure, I got a reman unit from Oreilly and installed it this morning. It was fine when I tested, had good brakes and went locked to lock quietly without fuss. Let the house and within a mile, I lost steering and brake assist. I stopped and turned around, but what I am noticing is that at idle, I have no power steering, but when the RPM's are up, I do.
View 3 RepliesMy power steering pump camp keeps coming off. Almost like it's got too much pressure. I'm stumped as to why but it makes a mess whenever it comes off.
View 14 RepliesI just replaced my power steering pump and gear box and I flushed the system until the fluid came out good. I have done the whole lock to lock and pump the brakes but nothing is getting better.
View 3 RepliesDriving home from movies tonight, I lost power steering and power brakes and the pump started growling. Looked in the reservoir and it was all foamed up. Within the last 20k mi I have flushed the system and refilled with power steering fluid. No apparent leaks at this time. And happened like someone flipped a switch. Fine one turn, nothing the next. What are the chances this is a fluid issue and not a mechanical one? Start with flushing system and adding Mercon V? Or is it likely pump is damaged?
View 7 RepliesInitially had indications of a leak under the wheel arch on the drivers side.
About 3-4 months back replaced both PS lines and the leak stopped - briefly (maybe a couple a weeks).
Now the leak is back, but what's interesting is I lose more ATF fluid on a single long haul run than I do running round town for 3 weeks. I can't work out where the leak is coming from to identify what else to replace - short of just buying a pump and reservoir and replacing them as I've already done the hoses.
My turbo cooler pipe was hard up against the old PS pipe where it entered the side of the reservoir until I did the replacement hoses. Now I have it out the way but I'm wondering if it's caused some unseen wear or damage.
If I just do the pump to see if that works are the reman units any good out of Autozone or O'reilly's?
I was getting ready to replace the carrier bearing and noticed the rear pinion seal is leaking. Before attempting the replacement myself, I would like some opinions on the noise in the video below. Is this normal? I am confidant I can replace the carrier bearing and pinion seal, but not sure I have the tools for anything else.
YouTube ...
2003 F-350 - 7.3. With the key in the on position there is zero voltage to the fuel pump. Fuel pump fuse is good. I traced the red with black tracer wire from the pump up through the firewall and to the safety inertia switch. The switch has continuity so it's OK. Then from the safety switch I traced the green with yellow tracer wire to a fuse block plug connector. Then I checked continuity from that connector out to the #40 fuel pump fuse and it's open.
So I then i checked from the fuel pump fuse to all the back connections on the back of the fuse block and there was no continuity to any of them. So I removed the back cover off the fuse block to expose any issues. I found two board mounted relays. Now, from the fuse I get continuity to one of the relay connections. So did Ford hide the fuel pump relay and make it non replaceable? Also if this is the pump relay then what circuit energizes it? I need to make sure before I replace the fuse block.
I have a 2003 F250 and dont have power at fuel pump, or fuse #30. I put power directly to fuel pump and it worked and truck fired right up.
View 13 RepliesThere was no power getting to the fuel pump on my 2002 Ford F250 73 diesel traced it back to the inertia switch no power in or out but I'm getting power at the fuel pump relay put the code scanner to the PCM and no communication....
View 9 RepliesI have a 2004 with the 4.6l. The high pressure hose is leaking from rust. From other posts I have read, it looks like I should rent a puller and remove the pulley first, and then I'll have access to where the hose connects to the pump.
Question: The leak occurred while driving home from vacation today. Went we stopped for gas, we noticed a shutter in the steering. I added about a 1/2 quart to the reservoir - there was still some fluid but foamy. I made it home, and I when I checked again the reservoir was empty.
Should I go ahead and replace the pump while I am at it? I wondering it if could have gotten damaged from low fluid. The truck has 190k so it's not like the pump owes me anything. Will it make any of the repair easier to toss out the pump too?
I was driving my truck then all sudden truck started losing power then slowly died. I restarted it, it was a lil shacky then died again. Iunscrewed the fuel filter and looked in the housing and there was lil fuel in bowl i turned the key to on position and bowl did not fill with fuel looked as if it were shooting some bubbles up(air) could it be outta of fuel???
View 10 RepliesI'm going to be replacing my lower radiator hose so figured might as well switch over to the extended life stuff going to probably go with the Delo ELC.. Supposedly it's good for 750k.
View 14 RepliesMine was clogged again, and I check it every month.
View 14 Replies2011 F-350 CC, 45k miles... Found out yesterday mine is leaking. Way to early for these issues to pop up.
View 1 RepliesI have a 1989 Honda Accord DX with less than 120k miles. I have two problems.
1) the low pressure hose for the power steering has worn out and is leaking by the fittings (badly) and I can't find the parts to fix it. The high pressure hose was also leaking but we found and replaced that part, and
2) I accidentally topped off the power steering reservoir with brake fluid (this was after I already knew the leaks existed).
After chasing the smell of coolant for a couple weeks, discovered that the upper radiator hose was leaking at the engine. Based on my schedule and drive schedule, and unfamiliar location this last week, I took my truck to the last people I wanted to - the Ford dealer, where they attempted to charge for the hose replacement. During this time I discovered the nature of how these hoses work and asked the tech why they don't just replace the O-rings ... "Ford Motor Company wants to sell you a new hose with labor" - a direct quote from the Ford tech. And that is why Ford is the LAST place I want to go for repairs I cannot perform. I kept the old hose - any spot where you can get the O-rings alone?
View 5 Replies