Ford A/C :: 1992 - Clutch On Compressor Froze And Nearly Burned Belt Off Of The Pulley
Jul 11, 2011
My air conditioner had a problem a few years ago. While idling in the driveway on a really hot day the clutch on the compressor froze and nearly burned the belt off of the pulleys before I killed the AC. I continued to drive the vehicle for several months but without using the AC.
Fast forward 5 years (almost) and I just finished installing a new engine and putting a shift kit in the transmission.
Remembering the original AC problem I know that I need to get this fixed. I noticed while checking all the engine functions that the compressor clutch is not stuck any more (maybe all the oil leaking onto it worked with this).
As it stands now, the AC seems to cycle normally but it doesn't get cold and probably needs a charge at a minimum. Is it possible that the compressor clutch will work fine or is it a disaster waiting to happen? What else should I check in the AC system?
I'm not against replacing the whole system or any single part of it. I am also not sure whether the AC uses R12 or R134. How can I tell?
View 9 Replies
Advertisement
I need diagnosing why my A/C isn't working. I'm wondering if my clutch staying engaged has burned up my compressor before or after my clutch went bad. I don’t think it’s the air gap issue because I took my clutch off and checked and there were zero washers. I guess somehow I re-installed it with no washers maybe the last time I fooled with it.
I've only knew to check the air gap trick and when that didn't work, I wasn't sure what my next step could be. I tried looking at the high side pressure switch connector to see if it was burned up and it looked ok.
Can track down if my compressor is still good and replacing my clutch is the only thing I need to do or if I need to replace my compressor? Or if there's something else that's totally unrelated that I need to check?
View 14 Replies
99 AC compressor clutch pulley locked up. I replaced the serp belt because it failed, then noticed the AC outer pulley was locked up. I could turn the inner clutch assembly with the 14 mm nut with no problem. So do I need to replace compressor, or can clutch assembly. be repaired on car?
View 4 Replies
2006 6.0l ... I've read all over for tips on routing this belt and everyone plays it off as being some simple '20-minute' task. I'm on my 4th hour on this now.
I can't figure out how to route the belt around the tensioner pulley, circled in the picture (from another thread). Everyone glosses over how to do this and I can't figure it out.
It seems like the only way to get it on is to bend the belt and slide it between the pulley and the block, but that I just can't reach the blasted thing.
View 4 Replies
One of my belts squeaks. I've tightened one of them as far as it goes I think. The other one is the one with the alternator. Do I tighten the pulley bolt on the alternator to add tension to that one?
View 4 Replies
I am not sure which it is but I cannot turn the pulley by hand. How do you tell if the pulley is bad or the whole compressor? I went out to start the truck and it wouldn't start. It died so I restarted it and then I seen the smoke from the front of the truck. I opened the hood and the flipping belt was just hanging there. Is there a way to just bypass the unit for now? I wont be needing the AC till summer and that is several months away.
View 3 Replies
I have a 2008 F-150 with a 4.6. I have a sequel and I believe it is the belt tensioner pulley and / or the idler pulley above it. Looking for proper procedure to change one or both. It is pretty tight in there. How much stuff do I have to remove to get in there. Should I replace both pulleys at the same time.
View 2 Replies
Need to replace the ac compressor bearing/pulley on my 2001 f350 7.3. My question is do I need a special tool like a pulley puller or is there another way to remove pulley? I already have the clutch assembly removed as well.
View 1 Replies
In a few weeks I will be bringing my new to me Ranger back to the great state of Texas. The truck however, has a squeak when running, which I think has been concluded as the idler pulley for the timing belt. Well, I'm nowhere near the truck still and in order for it to get here it will need to be driven half a day to reach me, at which point I could do all the work it needs done.
My question is: Should I take the risk and have it driven here before the belt change (I did look at it while I was out there and it's already cracking pretty good), or should I go ahead and have someone get the belt done at a shop? It's less the belt that concerns me I think, and more the pulley, even though it's just started squeaking in the last 1000 mile.
View 10 Replies
07 f250 I just replaced the power steering pump. I put the serpentine belt back on and when I started my truck I now have a squeaking noise. It's driving me nuts and the more I push the pedal it gets alil louder. Now before I did the ps pump I did hear a little noise like of bearings squeaking when I put my ear to grill.... I put the old ps pump pulley on the new pump but I don't think that is it because it is pressed on. Would it be a bad idler/tension pully? Is it just a coincidence after I do ps pump that it now decides to squeak?
View 10 Replies
Been trying to isolate my noisy serpentine belt. Had the belt off and spun everything, only thing I found that made any noise was the alternator. It had a nice churp like a bearing was on its way out in it. So I replaced that figuring my squeak was going to go away. No such luck. Listening to it again while it was idling, I crawled underneath. Almost seems like the churping noise is coming from the Crank Pulley. Is there a bearing on this pulley that goes bad?
View 13 Replies
I have a 2005 f-350 4x4 with a 6.0 power stroke now it's been causing me problems to the fact I couldn't find the problem the truck would smell like an electrical fire but last night I found that the belt is slipping on the seized a/c pulley but I can still spin the center clutch so can I just replace the clutch assembly? Or bypass the a/c so I can drive for the time being?
View 1 Replies
got the 4.6, AC clutch is just winding like crazy, so Im going to do a cheap fix and jus bypass the pully. Now do I need to remove the compressor or can I just get a belt for a 4.6 without AC and just not use it?
View 1 Replies
I purchased a new 2000 mazda b4000 2 weeks ago and the belt was squeaking and I knew I had to change the water pump so I replaced it and the squeaking didn't went away... I thought maybe my idler pulley bearing was worn out cause I could see it wobble back and fourth when the engine was running... Replaced it, still squeaking! Change my belt still squeaking! look further turns out my power steering pulley wobbles slightly. I'm thinking about trying a gator back belt and see if the squeaking goes away. Could it be dangerous to run the truck as it with a slight misalignment in the power steering pulley? or it'll be a must replacement asap?
View 3 Replies
I have been waiting for the pulley to be replaced and was just informed that the air compressor put in last July was defective. The compressor is being replaced because it's under warantee but I'm wondering if a defective air compressor could have caused the pulley to break.
View 2 Replies
I have 1997 F250 LD since i bough it has been doing this chirping sound coming from the serpentine belt and the pulley area but when the truck has been working for 15 - 20 min it goes away
This is apart from the from the problem before I think the fan clutch is broken because when I start the truck I can hear the fan going at the same speed of the engine is that normal ? even when the truck is cold
View 3 Replies
This is my first Subaru, and I absolutely love the vehicle; however, because of it, I'm very new to its mechanics. I bought it used from a friend, and I've been driving it for three weeks now, now this noise has come up and I want to verify what needs to be fixed before I start taking things apart. Perhaps you all know what noise this is coming from the compressor/ac idler pulley area?Here are a couple of videos.
[URL] ...
[URL] ...
In case it does somehow matter, one of my knowledgeable friends asked me if it makes more noise when I turn, and the answer is no. Also, the noise does not come through the speakers, and from what I understand, that eliminates an alternator problem.
View 4 Replies
It has developed a weird squeaky belt or pulley sound. It starts after few seconds of start up and goes away after driving few kms. It also goes away immediately for few kms. When I spray WD-40 on generator/alternator. Once in a while the sound decreases by itself and goes away only when I press the gas pedal and comes back during idling/braking. The belt is almost like a new. The car drives great without any issue.
View 1 Replies
1992 f150 4.9L, bought it a couple of months ago knowing the ac wasn't working PO had it converted to 134, said it worked great until they put on the bodylift. Compressor clutch is working, I'm sure I have some blend door issues but I've bypassed the heater for now.
AC on max, outside temp 85*, engine off high/low at 100psi, engine at idle low 55psi high 125psi, center vent reads 93*. When engine at apox. 1800-2000 rpm, low 35, high 180, center vent reads 85*.
My guess is the compressor is worn out. Is there another way to test? If I do replace what else do I need to replace? I'm hoping there's something else I can do/check before replacing the compressor.
View 6 Replies
I'm trying to remove the AC belt off a '96 Geo Prizm. I've loosened the idler pulley adjusting bolt, per my Chilton's manual, but it doesn't loosen the belt. It's as if the pulley is stuck in the bracket. Even if I completely removed the adjusting bolt the pulley wouldn't budge. How can I unstick this thing without damaging the pulley?
View 6 Replies
My compressor on my 92 Ranger did not have any clutches on it. Where they went. I got a compressor off of a 94 at the pick and pull. It was charged and the compressor turned fine. Brought it home and tried to install it. My hoses in the back of mine(92) are different than the 94. I went back and got the hoses, condenser and evaporator off of the 94. Put it all together. The high pressure hose on the 94 has some sort of switch on the high pressure side. What is this switch for and how can I wire it in to the electrical system on the 92? I assume it is some sort of pressure switch that allows the system to flow. I'm getting 30 pounds on the low side and 150-200 ponds on the high side. Also, when I increase the RPM's, the compressor kicks on and off. It's not like it would or should normally but fast.
View 7 Replies
