Ford Aerostar :: 1995 - Rough Idle / Jerky Acceleration
Apr 15, 2006
Symptoms: (162K miles, last tune up about 70K miles ago) rough idle, and poor acceleration. Occasionally, the car really jerks while accelerating. I read about new plugs/wires, and something called seafoam. I think the highway patrol would pull me over as a gross polluter, but that too seems worth a try. Various sensors and hoses, I'm frankly overwhelmed. Where to start?
Something I learned today: My car was made in 10/95. Apparently, I can scan for trouble codes?!? How and where? Is it OBD I or II or something else? Dumb question: I can't even get the interior engine shroud off. I found three clamps, but it still hangs up near the top. What am I missing?
View 14 Replies
Advertisement
I have some major problems with my explorer. The idle is rough and accelerating is rough also. If I nearly put it to the floor it almost seems like it studders the power. it will feel great for a second that feels like it's less power for a second then more and less and more and less. When I'm sitting at idle, it will idle fine then after a minute or so it will bog way down and shake the whole vehicle. when that happens I give it some gas and it comes back to normal idle then it does it again after sitting for another minute. I've replaced spark plugs, wires, alternator, oil change and some tires. I've been told by many mechanics it could be the IAC Valve or the fuel pump or the fuel filter or a vacuum leak.
View 8 Replies
I have a 1999 F250 SD V10 4x4. I recently had a transmission installed and the truck is running erratic. I have an engine miss (sometimes when idling, more so when in drive and foot on the brake). I say sometimes because there are times it will not miss and the engine runs smooth. The transmission shifts a little strange and sometimes hard.
I am getting a code reading that says my TPS is faulty, but I installed a new one a few months back.
The engine is running rough (jerky on acceleration) especially when driving. I was wondering if I should take it to a shop and have them flash the computer to reset it?
I also remove the AC compressor a while back (bad clutch). I installed an aftermarket pulley.
View 2 Replies
So I have a 95 aerostar 3.0. I use it every day my a delivery vehicle. I keep it maintained. About a month that ago, it developed a skip or a hesitation, most!y at high speeds, usually under load. I thought it may be transmission but had it checked and was ok. I drove it like that for several weeks. Then got worse so I parked it for ten days until my mechanic was available. When I cranked it to drive it over, it spit and sputtered the whole way here and barely made it. It had never done that before. He changed plugs and wires and distributor cap, even though it had been less than a year since all that had been done. Still no change. Driving way worse after sitting for ten days.
View 6 Replies
I purchased a 2012 Subaru Forester 2.5X Premium (automatic transmission) in November 2011 with 4 miles on it. Since the get-go it has had issues, but we thought that some of them might work themselves out as we broke the car in (which we were religious about). At the first oil change, we told the dealership about the issues we were experiencing and got the expected "the computer doesn't say anything is wrong" and "we couldn't replicate the problems" excuses. We were told to bring it back if the problems continued. Well, they've gotten worse. Here are what we are experiencing:
- Erratic shifting. I commute from the mountains to the city every day, so I need power from the car. Sometimes, when I'm heading down a hill and I tap the gas slightly to give myself a little boost, the car will suddenly downshift, even though it was sitting at 2500 RPM and didn't need to get any extra power beyond more fuel. Going up the hill is worse, as if you are not actively accelerating (including if you are trying to maintain a constant speed), it will upshift on you and you lose all power, so it will need to downshift to make up for this. It does this constantly for the entire drive home. Everyone who has driven this car in the mountains has experienced this.
- Jerky transmission. When the car shifts, it is super harsh and tends to throw you forward or back. Even when on flat ground it shifts roughly.
- Sluggish acceleration. If I give the car any more gas than I usually do, it hesitates before going anywhere. One day I needed to get over on the highway fast and floored it - it took the car about 2 seconds to respond. Then, yesterday, we were turning on to a highway from a side road and I tried to accelerate (gas about 1/2 way to the floor) and it didn't respond at all for about 5 seconds and the "Check Engine" and the traction control lights started flashing at me. We were on a paved road with no gravel, water, ice, etc and the traction control light began flashing on the straight, not while we were turning. There are also days when it feels like there is an anchor tied to the car and it just doesn't want to give me any umph at all.
- Rough starts. This is the really weird one as there is no rhyme or reason as to when it happens. Some times it takes the car several revolutions to turn over. Oddly, it's never on the really cold (under 20 degrees F) days, but it has happened when it is ~35 degrees and a couple of times when I have started it in the middle of the day to grab lunch and it is ~65 degrees out.
- Running rough. This usually happens after a rough start, but can also happen at other times. It just idles very rough and won't calm down. These are the days I have the worst time with the shifting issues.
I had a 2001 Forester that threw a rod, which forced me to get this car. Everyone who has driven both agrees that the 2001 was quicker, easier to drive, and had more gumption than the 2012. It also had less problems even though I purchased it used in 2005 (until the whole rod-throwing thing, of course). I really want to love my 2012 Forester, but I am so upset that, for the first time in my life I have a new car, and it runs terribly.
View 28 Replies
When I first start me car up, doesn't matter the outdoor temperature it idles terrible jumping up and down. When I go to put it in first gear and attempt to pull out it's very jumpy/jerky because of this rough idle. Once I drive a little bit if I stop it will idle fine. This problem seems be slightly worse when it's wet/raining/humid.
Its throwing codes P1128 Manf Control p0300 multiple misfires and then p0301,0302,0303,0304 which is misfire for that individual cylinder. Also my oil light blinks once in awhile, think that could possible be sep issue though.
I changed plugs, the old ones were really white... I believe that means running lean?
Put in new coil/wires
Gas Filter
Mass air flow sensor
Changed 02 sensors
Also did the seafoam treatment, none of it seemed to work...
Though about possibly changing temp sensor next. I hope it has nothing to do with fuel injectors....
2000 Jetta 2.0l 4cy AEGengine
View 2 Replies
1992, shory 3.0 130K MILES
On start up runs very rough, will stall if not power braked or revd a little on start up/out of the driveway.
VOLT METER STARTS GOING NUTS!!
After a mile/warm up,,, runs great. But sometimes even when its hot, it will still try to do the rough idle briefly after just a few minutes restart. Give it a few revs at that point and its good. And once in a blue moon it will do it randomly at a stop light,, out of the blue. Very rare
View 12 Replies
1986 3.0 liter. I have a problem, concerning no power. The van starts and idle is slow and a bit rough. Something is not allowing the engine to spool up much past an idle, thus moving past 10 mph is not an option. When you try to rev it, it's like it's either starved of fuel or the ignition advance isn't working. As it is basically winter, with a temperature today of about 25F or less, it was suspected that I'd put in bad fuel (as in, containing water) and possibly the system is partially froze.
When I turn on the key, I can hear the fuel pump pressurize and then shut down, as it normally does. Gas line antifreeze was added but no change; we limped the vehicle at 15 miles or less for almost 2 hours. Likely if the fuel system had ice in it, it would've cleared out by then. As it happened on the road, I'm at the mercy of a shop of which/whom I do not know. Would it be advisable to instruct the mechanic to check for fuel at the "Schneider" or fuel pressure release value, located near the manifold?
View 1 Replies
Well I was afraid this was going to happen. About a two years ago, several months after I replaced the heads on the van that at the time was my brothers, the ignored a squeaking pulley. One day that pulley seized and broke the belt. My brother was not watching the gauges closely, and didn't realize anything was wrong other than the clunk noise that happened when the belt was thrown. That was until he went to turn, and the power steering was gone. He looked at the gauges at that point, and the heat was pegged out on the gauge. So he pulled it over and shut it down. I came and towed him to a shop where it could be fixed.
But I fully understand that when an engine gets overheated, especially if the heat build up was rapid, the heads warp. I also understand that the head gasket will usually seal anyway, so the failure does not often happen at the time of the overheat.
Well, it finally let go the other day. Started noticing a rough idle and an obvious misfire. Removed the cap and there is a steady stream of small bubbles when the engine is running. There is also more corrosion than should be in the cooling system for how recently the coolant was replaced.
It is not overheating right now, but isn't this a lovely time for a major problem to occur. Anyway, I took it in, and hopefully they will have it finished before I need it again. My van performs truck roles, including towing and all of my fathers trucks are either too small or on deaths door. I'm sure it would drive most of you nuts anyway, but do not ignore squeaking pulleys.
View 11 Replies
I just replaced the water pump and put it all back together, now it won't run well enough to drive. Checked vacuum system, all sensor connections, hoses, gas cap, changed fuel filter, I can hear the fuel pump kick in, reset system with battery disconnected and have looked at everything I can think of so far.
Now - starts fine, idles about 10 seconds and then begins to idle rough and dies. If I use the throttle I can often keep the idle up, but then backfires or acts like no fuel and again dies. Used fuel cleaner and made sure there was plenty fuel in tank.
I am looking at replacing sensors at this point but which one first?? They get a bit expensive real quick.
View 5 Replies
My truck is a 1995 Explorer 4.0 150,000 miles, 5 speed.
Problem - Rough idle : when cold it's worse and will stall and choke a little. When warmed up it just has a rough idle but will not stall and stays at a pretty constant RPM. It's very tolerable when warmed up but still not right. It drives fine once off idle. No black smoke that I can see. Power may be just a little off but I would not bet on it. MPG seems about normal but haven't been on a long enough trip since problem started to tell for sure. Also longer than normal cranking on occasion.
Diagnostics so far : Fuel pressure is at 32 PSI, vacuum off regulator it's at 40 PSI. Not sure about key on only as I don't trust the autozone loaner gauges. You have to fiddle with it each time before it will read. Leak down after 30 minutes was about 4 PSI
No Check engine light ever. KOEO test shows no hard or on demand codes, I get the 111 pass. From CM I get 336 and 45.
336 is EGR related and my looks pretty rusty. I put a vacuum pump on it while running and the EGR held vacuum but had no effect at all on idle, I was expecting it to get worse as I opened the EGR so it may be stuck.
Searched high and low for vacuum leaks by ear, visual and with starting fluid all turned up nothing.
Actions so far : Replaced plugs, wires, IAC, and fuel filter. Cleaned MAF sensor and throttle body plus ran lucas fuel injector cleaner through it.
Next steps : I've got the EGR but it's so rusty I am sure I'll break the tube it bolts to plus I don't know it that alone will cause the rough idle. Will the DPFE sensor and/or EVR create a rough idle yet not turn on the CEL?
Thought about changing the fuel pump and/or regulator but the numbers are not terrible. Agree?
Thought about changing the intake gaskets but don't see any leaks.
View 8 Replies
1995 ford ranger with 4.0. It idles rough. Replaced MAF TPS fuel pump fuel filter fuel pressure regulator upper o2 sensor. IAC.. still idles rough RPMs drop. It isn't as bad since replacing MAF but still not right. What else is there.. Cleaned out the air intake port it was gummed up. Don't know what else to do?
View 3 Replies
My 95 4.0 has had a periodic idle issue for quite a while. It seems it may be getting worse. Here is when it may only happen:
Vehicle is fully warm. I shut it off for about 1 hr or so and when I restart it, it shakes and misses in idle. It will idle fine after I drive it around or if I rev the engine for a while when still parked.
This never triggers the "check engine light". New fuel filter, plugs and wires.
View 1 Replies
I have a 2000 F-150 5.4 L. I was driving from home and seconds after the engine went into a rough idle that wouldn't let me accelerate. I scanned it and gave me multiple transmission trouble codes, about 15. I checked the wiring, the transmission fluid and it all looked good. So, what could be the problem?
View 3 Replies
V-10 getting a weird hesitation on acceleration and rough, sporadic idle. Fuel filter is brand new, spark plugs only have 8000 miles on them. If im just cruising and give it just a little gas it gets real rough and wont smooth out unless I give it more gas. What else could it be? Coil packs?
View 14 Replies
My 95 3000gt is smoking after about 30 minutes of driving. Smokes mainly when idle and upon acceleration. car has about 200k in mile. what could cause this.
View 5 Replies
I have a 95 explorer, has been a great truck until lately. it started as just a small rough idle every now and then, nothing to make a big deal about. just changed the oil and wiped things down a bit, started it up ran just fine for a couple of minutes and when it starts to just barely warm up and the idle drops down it starts louping or surging, if i hold the throttle open it bit it kinda goes away and it would continue to warm up and not have a problem idling. now it won't even do that. i'm pulling several codes, to many to list and the truck ran just fine a few days ago ...
View 3 Replies
My 07 F150 has no power. I changed the timing chain, cam phasers, spark plugs and all 8 coils and still no power. Rough idle and bogs on acceleration.
View 3 Replies
I have a 04 FX4 scab with a 5.4L and am having issues with it idling rough, and low power and stumbling upon acceleration and cruising speed. I did a scan and the codes show lean run condition, misfire on cyl 4, etc. I changed injector and coil on #4 and it seems worse. Scared to change the plugs, until I can leave the truck down a day or two in the event that I break one or more.
View 10 Replies
I have a 1998 Ford Ranger. My problem is jerky application of acceleration. I note slack in the cable connecting the pedal to the engine throttle. Is there any way to adjust this cable length to remove the slack.
View 5 Replies
2005 Ford F150 lariat 5.4
I had a misfire under a bit of a load (acceleration) and up hills. I changed spark plus with OEM Motor craft ones, truck ran super nice for a couple week.
Had the engine light flash, slow down and the RPM go up a tiny bit then back down and the light goes off
Now I'm back to miss fire different location, and a rough idle. I've swapped coil packs around and the miss fire stayed on cylinder 4.
Spark plug screwed or injector or ?????
View 14 Replies
