On my 99 at the tip of the springs there is what looks used to be plastic wear spacers between the leafs. Mine are worn out and I think it is part of a squeak noise I am chasing.
What that part would be, where I could get them, and do I have to break down the leaf assembly to change them or could I raise the truck by the frame and take the load off the springs enough to get the in?
I am replacing my rear leaf spring hanger and shackle. I have one side done and the other side the old hanger is off. I am ready to install but the bolt/ bushing in the leaf spring will not come out. I tried every thing with what i had for about 2 hours. Is there a tool to remove these things similar to a ball joint press.
View 14 RepliesI've got an '08 FX4 that has developed quite a loud and annoying squeak from the rear leaf springs. It happens when I'm slowly applying power and going over bumps such as speed bumps or similar. More so when I'm going up hill.
I initially thought it was a u-joint going bad, and had my driveline mechanic take a look at it. He discovered it was the rear leafs making the noise. He sprayed them with an aerosol light grease and the noise was instantly gone. The problem is, the noise comes back after the grease spray has worn off (usually after driving in the rain) which happens a lot in the Vancouver area.
This is my 3rd Ranger and I have never had this problem. I don't drive in unusual places (beach, sandy, dusty areas) so I don't know why this is happening. It does look rusty in the areas that I can see in between the individual leafs. Is this a common problem for this vintage of Ranger?
2003 f250 6" lift on 35s. How to lift the suspension to change out spring bushings? Was thinking using two chain falls on tow hooks on the front, any easier, safe, cheaper way. I have a farm jack but need to weld a plate on bottom of it for more support...
View 5 RepliesConversion from the dana 50 to the newer dana 60 with coil spring? My Dana 50 has called it quits so while my front end is already off the vehicle already why not make improvements. Ford used the 50 for 1999 to 2002 then upgraded to the 60, I'm guessing it was for a reason!
I've read this article on a similar project but the dana 60 had leaf springs as well: Dana 60 Conversion for F250 years 1986-1996 .: Articles I'd prefer coil spring, nothing more then personal preference with a bit of better ride quality. The donor vehicle is a 06 SRW F250 This is not what I'll be getting but just as an example of the parts I would get.
Replaced front leaf springs to procomp, now i got a clunking noise from right leaf spring rear eye(and a little bit from the left).
Can it be that:
I've tighten them to much? Wrong way (big eye is in front)? Got about 4" lift in front and haven't received rear leveling kit yet so the angel is wrong?
My truck in the signature is 21 years old on original Leaf's. Is it time to change them? Do the backs last longer than the fronts?
View 5 RepliesI have been having that nice thumping noise that generally accompanies worn out sway bar bushings. I did bushings last spring but a noise came back shortly thereafter. Finally got bothered enough/ found enough time to take a look at it and tracked it down to the sway bar again. My right front axle mount has taken damage before and is now all bent up, not allowing the bushing clamp to hold tight to the bushing. Pictures of the issue are below.
Front view of the entire mount.
Rear view showing the sway bar mount plate.
I am unsure what to do about this mount. As you can see it has been pretty messed up by the PO. What could be done to fix the issue?
after I had my springs installed I noticed this air sound when I go over bumbs. is this normal.? if I upgrade my shockts to aftermarket will they make the same sound?
View 9 RepliesHow to remove the spacer from the rear-end, spring and axle housing. If so, would it be the best to remove one at time etc. Must they be re-located below the axle or totally removed. I don't have a hoist to work from only floor jacks.
View 14 RepliesOk I have an f 150 04 fx4. 120k miles. I was checking a drip on the transmission cooler, and noticed my passenger side coil spring is broken 2nd coil from the bottom. Truck rides well, but obviously this needs to be addressed. Break looks old since it is rusted over, I probably relocated from new England to Florida driving this down 95 with this break, scary.
View 6 RepliesI have a '92 Aerostar XLT with a rear control arm problem. The bushings have worn out and the rear end floats side to side as much as 1 1/2 inches. Ford says one bushing comes in the arm ( no longer avail ), one is a press in (no longer available), and the other is like a strut bushing and is available but without the other 2 there is no point in replacing the one. How to fix this enormous problem???
View 10 RepliesThe local shop here suggested getting a set of F350 springs and they would take them apart and a leaf to the front and rear springs.
View 2 RepliesI got the new ones, (as mentioned in another thread) and they're the same as the old ones. Well, the one that's still in one piece.
I guess I'm missing something very simple, but as easy as it would be to cut the old one out...how do I make room between the lower leaf and the other leaf pack to get it out?
I about hung from the lower leaf and it didn't move quite enough to give the room to remove the bumper.
My leaf spring swap is almost complete... its been almost 3 weeks with all the conflicts of life but its getting near completion. Just have to do front passenger side now.. Tomorrow and it should all be done.. hopefully... Any ways... my preliminary numbers are 40" front (ground to fender) and 41.5" rear.. Might be 1/2" to 1" off since I haven't finished the job AND the truck is sitting on dirt. Any ways, What size wheel/tires can I fit on there now? And will I need a spacer with that size?
View 1 RepliesI'm scheduled for my first HPDE next week and I just discovered that the bushings on the front end links are worn. I don't notice any issue when taking curves and I'm asking due to the timeline of when the dealer will get the parts...it'll be cutting it close before the event.
View 3 RepliesWhere I can get or have a speed nut for the front eye bolt of the right rear leaf spring? If you do I'll gladly send you some cash for it and to cover shipping it. It's supposed to rain pretty much all week here and I really don't want to go to a junkyard. I have checked ford parts and nothing there you can get the hanger that attaches to the frame that the spring bolts to but not the speed nut or bolt only need the speed nut though. Truck is an 2004 f-250 so 1999-04 will work and 05 to 07 is setup the same in the rear but I don't know if they are the same size bolt since they made the frame heavier. I have no idea after 07 when they made the springs longer.
View 1 RepliesI bought a used 2007 Lexus RX350, FWD, in December 2012 and had it looked over before I signed the papers by a non-biased mechanic. He said the control arm bushings would need to be replaced in the future.
When I took the car in last month to my mechanic (a private mechanic, not a Lexus dealership), he said the control arm bushings on the right side are worn a lot more than the left side. He said on this Lexus, it would require removing the engine to replace the parts (?) and that because it was such a labor intensive job, and the left will eventually wear, that he advises I get both the left and right replaced at the same time.
I just realized my driver's side front leaf spring on my 2002 F250 has snapped. I checked the weight sticker on my truck and it weighs 5200lbs in the front. My question is the heaviest springs I found only support 2630lbs a piece, so being a 7.3 is 5200lbs a correct weight for the front of this truck? also why would Ford make springs that support only 60lbs more than the front weight? Hell I weight more than 60lbs.... Did I snap the damn thing just by climbing into the cab?!?!
View 6 RepliesMy front passenger leaf spring just broke on my 2000 f-350. My front springs are T code, but I was wondering if a could replace the broken one with a code X spring as a temp fix until I get a leaf spring replacement delivered?
View 1 RepliesWhat is the width between the spring perches on leaf sprung 99-04 front axle. I searched and cant seem to find a dimension listed anywhere. i tried the dana60 bible on the pirate site as well, but it doesn't list the spring perch dimensions, only for the pre 99 styles
View 2 Replies