Ford Escape / Hybrid :: 2005 - Clunk Noise On Front End When Braking Or Accelerating And Turning Wheels
Oct 10, 2015
2005 2.3Liter 4wd Mariner, 225k miles
I have been experiencing clunk noise on the front end when braking or accelerating and turning wheels.
I have replaced: front control arms, ball joints, tie rod ends, sway bar bushings and stabilizer links and 2 days ago I replaced strut mounts and bearings.
The steering is smooth after the strut mounts replaced but I can still hear cluck noise mostly on left now when going over bumps, braking and accelerating.
Car also has new engine/trans mounts.
I am so lost right now because I cannot figure out what is it. The only thing I didn't replace are the struts but the I test them and they seem to function fine.
View 5 Replies
Advertisement
2005 xlt 4x4. I was cleaning the threads on the rear constant velocity joint before taking the nut off. Turning the hub was almost impossible without using a steel bar. Is it supposed to be this difficult to roll the rear axles? Yes the selector is in neutral....
View 2 Replies
A friend has 2005 escape 3l. He called me yesterday saying that he needed replacing his fuel pump.
Before I got to his place he had already replaced the fuel filter...
We got the pump replaced, and when we went to start the vehicle, it still wouldn't start.
We double checked to make sure everything was connected and plugged in and it was. We checked all fuses, and they were all good.
This morning I am going to try jumping the relay and see if that does anything. What else to check?
View 3 Replies
A clunk sound coming from the front end. Drivers side and Passenger side. Not really a metal on metal sound. The problem started after coilover install. The sound occurs while braking and accelerating over bumps. So what I've replaced:
-Strut Mounts and Bearings
-Lower control arm bushings (R32 bushings)
-Drivers Side CV axle
What I've checked:
-Tie rod ends have no play
-Ball joints have no play.
-I have no sway bar, so not the sway bar bushings.
-Its not the axle hitting the frame.
Could possibly be the dog bone mount but when I installed the 1' motor mounts I saw no issue but could possibly be the bushing. feel the clunk in my foot as well.
MK4 2000 Jetta 2.0 5speed With Raceland Ultimo Coilovers (Junk)
View 13 Replies
I just changed my stabilizer link front right side and it did not solve the single clunk noise that I hear when accelerating and braking.. although it did solve the "multi clunk noises and creaking I get that is now gone away.. but this other single clunk noise what else could it be from it does it when driving straight and there are no clunks when turning. I must add that is that I can hear it and its a low pitched clunk... and is also felt in the steering wheel.
View 2 Replies
My 2007 GX470 is making a clunk/thud noise when braking (more often when braking hard or on a downhill slope) and then again when I let off the brakes and start to accelerate. It is significant enough that I can feel the car jerk some when it happens, almost as if someone has tapped the back with their car. What it could be?
View 2 Replies
I seem to be having a clunk noise coming from my car when braking to a standstill or accelerating from a standstill.
Its totally unpredictable but only happens when braking or accelerating under 10mph.
No noise when going over bumps or turning and its only heard when the windows are down. What it could be?
View 13 Replies
I need to find a diagram of the door panel on the drivers front door. Need to see how to remove the switch bezel to check the power window switches.
View 2 Replies
My fiance drives a 2006 Escapse XLT v6 AWD. It's really a great car.
She noticed an issue when she filled the fuel tank the last time. It took about 8 miles of driving for the gauge to read full after being filled from empty. She also told me there was a "whirring" noise when shutting off the car and turning it back on. I checked it out and found the fuel gauge is making a noise. Whenever you shut it off or turn it on and the needle moves there is a distinct whirring noise that sounds like dirty plastic gears meshing, which is what I'm assuming is the issue.
I've done a search and came up with 0 results. Can the cluster be disassembled and possibly just clean the gears?
View 5 Replies
We have a 2005 honda civic hybrid; there is a squealing noise coming from front passenger side, when braking, when accelerating, decelerating, but not while driving at speeds of 30 mph, straight. Also when backing up, turning wheels. It's going to the mechanic on monday for regular maintenance, 100K miles, etc.
View 3 Replies
I've just replaced a front ABS tone ring on my 2003 Escape and I'm ready to replace the axle nut (I've got a new one, as per Ford's recommendation) and torque up. I've heard that you're supposed to torque the axle nut *before* you put the wheels back on the ground, but I have the factory service manual for the 2003 Escape and I can't find anything to back that up.
I've looked at every listed procedure I can think of that involves removing and replacing the axle nut, and none of them specify that you must torque the nut with the wheels in the air.
It would be easier for me to do it with the wheels on the ground, but would I be risking bearing damage if I did that?
View 9 Replies
My girlfriend has an 05 ford escape with a 3.0 the car has been well maintained it has 184,000 miles on it. Over 3/4 of the miles were highway. I have noticed that it has had a slight engine ticking noise i have researched and some say the tensioner some say retorque the cams? I have not been around these cars much. I replaced the alternator the other day and serp belt all pullys felt fine. The engine used to tick all the time here lately sometimes when it gets started it does it and sometimes it doesn't.
Also what fluid is supposed to be ran in the tranny the owners manual just says mercon, so do i just run regular strait mercon fluid in it? or does it need like mercon V. The car runs fine i just want to fix the ticking noise if its something major. Just some thing I've hear about on a buddys newer f150 with a 5.4 the oil supply ports that lube the timing chain tensioner got plugged and it developed a ticking noise? I am a mechanic so i can check and do anything i just dont know where to start on this car?
View 1 Replies
I test drove 2 2005 escape limited v6 2wd today. Both of them were pretty loud in the cabin at idle. The noise and vibration did lessen after the car started to move. Is this normal for escapes or does this indicate a problem somewhere? Like engine or transmission mounts.
View 2 Replies
I have a 2002 Ford Escape 3.0V6 with high miles. A while back the transmission on this vehicle went out while at work. I got the bright idea that I would tow it home with a dolly until the funds were available to make the repairs. We pushed it up onto the dolly and secured it. I also put it in park. It took me about a 1/4 mile to figure out what was with all the resistance (my first thought was "Dang, that sucker is a lot heavier than i thought"). I pulled over, put it in neutral then proceeded without any more problems. A junkyard tranny was put in it. Rides and drives fine. There is a whining noise that is very distinct and gets worse with increased speeds. It sounds like it is coming from the rear end. No noise while stopped.
I have checked everywhere i can reach to see if anything is hot... (thoughts were maybe a bearing) nothing found.
Fluid is full in rear end.
I just drove it and figured it would get worse or get better.
Now that winter is almost over I am very confident that the 4x4 is not working. It does not matter if you are in Auto or 4x4 only the front tires spin.
View 3 Replies
Couple weeks ago, was in a spot that needed 4wd. Turned the switch, the 4x4 dash light came on, but rear wheels didn't do anything. Lucky that we were able to get out with ft wheels only. Has 3.0, xlt version.
View 13 Replies
My daughter has a 2002 Escape 4WD with 3.0L engine.
Coming home from school a few weeks ago she experienced engine running rough on the highway when trying to accelerate. We ran the diagnostic on it and it revealed that #2 cyl coil was misfiring.
I've replaced all of the rear bank coils (in hopes that I wouldn't have to remove the intake manifold again anytime soon). I also replaced the connectors and weatherproofed them.
Replaced all the plugs while I had easy access too. This all went pretty smooth with exception of breaking 3 of the 5mm coil bolts off inside the valve cover. I've also replaced the upper and lower intake manifold gaskets.
It runs much better now except now on the highway, at 1800 rpm/55 mph if I try a gradual acceleration I get engine sputtering and it won't accelerate. If I push hard on the pedal it will downshift and accelerate normally right past this trouble spot. Other than this it idles and runs great.
I've noticed that the 3/4 in. vac hose on back of manifold is getting pinched closed about 70%. this is the hose that leads down to the top of engine just below lower manifold. I suspect this is the problem but cannot determine the root cause. I assumed it was the intake manifold gaskets but those are now replaced.
View 1 Replies
So my '99 F350 4x4 is making a clunking sound and there is a distinct jolt in the truck while this is occurring.
Symptoms: From a stop while accelerating, there is a distinct jolt and clunk. The best way I can describe the feeling is like something isn't tightened down all the way so there is a split second while inertia is generated and the "looseness" catches up to the acceleration.
When stopping, the clunk and jolt is generated when the truck comes to a complete stop. When the truck rebounds backwards a bit because of the suspension pulls it backwards after stopping, you will hear the clunk again.
I replaced the ball joints a week ago an a wheel hub bearing on the right side. I don't recall this before these repairs, but it may have been making this noise. I was more focused on the grinding from the wheel bearing so I may not have noticed the clunk and jolt then.
Where I should start looking for the problem?
View 14 Replies
So I am changing my transmission fluid tomorrow and was wondering a few things.
1. I noticed some people pull off the transmission hose to the inlet and keep draining that until its clear. For a drain and fill do you do it like that or just pull the plug and refill?
2. When youre filling it back up you just measure how much you taken out and then fill the rest by the dipstick? Anything else i should know?
3. Since I havent changed my transmission fluid in 60,000 miles. I wanted to do a drain and fill. I was thinking I needed to drain and fill it 3 time to catch up to maintenance. How often would you do it to get it clear? Drain and fill then drive it for a week then drain and fill? Or do it all in one day?
View 4 Replies
I have a 2002 3.0 Escape. All running great. I have a question about where engine load/vacuum is sensed for determining shift point? I replaced all of the dry rotted hoses in the vacuum recently when replacing intake upper & lower gaskets. since then, I've noticed the shift points aren't quite the same as before. The tubing I used was slightly smaller that the OEM, but otherwise, everything is plumbed up as before.
When accelerating, the engine does rev a bit more than before, before the tranny moves to the next gear. I can ease up on the throttle just slightly, and it'll shift up. If I'm not accelerating hard, it seems to shift fairly normal. Going up slight grades it doesn't want to shift as soon as it should, but on level ground it shifts fairly normal under light load. Going down grade it shifts quickly, as one would expect. This is why I felt it might be somehow related to engine vacuum.
Is there an sensor somewhere, a restrictor in the vacuum tubing, or a vacuum modulator I might look at? I've double checked the vacuum tubing and found no leaks.
View 6 Replies
I was having problems with my 02 Escape of misfire on cylinders. After doing a lot of checking, changing spark plugs, changing coils, ect, I decided that it could be the computer. So, I ordered one and put it in. When I turned on the key, all the gauges pegged and then came back to zero, but it acted like someone cut the power line to the starter. No click, no nothing. I checked fuses and they are fine. Even changed them around to make sure. Is there something that I have to do when you change the computer to get it to start? Had no problems with the starter prior, so it has to be something associated with the computer and changing it.
View 3 Replies
So we bought a new to us 04 Escape for the kid, he loves it! My question is, what's going on when I accelerate somewhat aggressively, the tach and speedo peg high and battery light comes on. It does not affect performance and gauges return to normal within a couple seconds.
View 11 Replies
