I test drove 2 2005 escape limited v6 2wd today. Both of them were pretty loud in the cabin at idle. The noise and vibration did lessen after the car started to move. Is this normal for escapes or does this indicate a problem somewhere? Like engine or transmission mounts.
View 2 RepliesI have been having this problem with Gf's car for a few months it is a 06 3.0 escape with 141K on the clock the car seems to run ok except at red lights and when in drive it seems to idle like its just about 100 rpms low when I give it a little gas just a touch it smoothes out. if I put it in neutral the car smooth's out but in drive when you come to a stop light or stop sign you can feel the rough or low idle in the steering wheel. She is nagging me and it has been very cold here in Pa and I'm trying to wrap my head around if it is a cold thing or just a coincidence. I'm fairly good at wrenching and I just need some things to look for as when you start the car up cold it idles fast like 12 to 1300 rpms and then drops to about 900 and in drive it seems like maybe it's about 600 to 700 rpms. but where to start to look Is it a sensor, vacuum leak ?
View 6 RepliesI have a 05 escape hybrid with 75k on it. there is a slight problem every once in a while when it starts the idle jumps up and down and when it is put in reverse it has no power to move. you have to put the pedal to the floor....there are no codes and ford has had the car for a total of three weeks, nothing found and of course it did not act up for them..
View 9 RepliesPosted earlier with my escape randomly stalling at idle. Getting a code po446 along with po511. Only stalls at idle after warming up and letting it set a while. When you go to recrank it that is when it won't idle or if it does its at 500 rpms or less. Also after driving it today it smells like rotten eggs. Replaced the idle control valve with no luck. What could cause this?
View 2 RepliesMy girlfriend has an 05 ford escape with a 3.0 the car has been well maintained it has 184,000 miles on it. Over 3/4 of the miles were highway. I have noticed that it has had a slight engine ticking noise i have researched and some say the tensioner some say retorque the cams? I have not been around these cars much. I replaced the alternator the other day and serp belt all pullys felt fine. The engine used to tick all the time here lately sometimes when it gets started it does it and sometimes it doesn't.
Also what fluid is supposed to be ran in the tranny the owners manual just says mercon, so do i just run regular strait mercon fluid in it? or does it need like mercon V. The car runs fine i just want to fix the ticking noise if its something major. Just some thing I've hear about on a buddys newer f150 with a 5.4 the oil supply ports that lube the timing chain tensioner got plugged and it developed a ticking noise? I am a mechanic so i can check and do anything i just dont know where to start on this car?
2005 2.3Liter 4wd Mariner, 225k miles
I have been experiencing clunk noise on the front end when braking or accelerating and turning wheels.
I have replaced: front control arms, ball joints, tie rod ends, sway bar bushings and stabilizer links and 2 days ago I replaced strut mounts and bearings.
The steering is smooth after the strut mounts replaced but I can still hear cluck noise mostly on left now when going over bumps, braking and accelerating.
Car also has new engine/trans mounts.
I am so lost right now because I cannot figure out what is it. The only thing I didn't replace are the struts but the I test them and they seem to function fine.
So I am changing my transmission fluid tomorrow and was wondering a few things.
1. I noticed some people pull off the transmission hose to the inlet and keep draining that until its clear. For a drain and fill do you do it like that or just pull the plug and refill?
2. When youre filling it back up you just measure how much you taken out and then fill the rest by the dipstick? Anything else i should know?
3. Since I havent changed my transmission fluid in 60,000 miles. I wanted to do a drain and fill. I was thinking I needed to drain and fill it 3 time to catch up to maintenance. How often would you do it to get it clear? Drain and fill then drive it for a week then drain and fill? Or do it all in one day?
Engine light flashing constantly with a vibration. It don't give any codes with the reader.
View 1 RepliesI only have one key and 2 FOBs for my 2005 Escape, but I do have the key number (4 digits plus a letter). I understand I need more than one to program another myself. Is there an inexpensive way to obtain/program a backup key?
View 9 RepliesI have the 2.0L 4 cyl. engine (2001 XLS Manual 114k miles). Runs fine when cold but once the engine gets warmed up it starts idling really low. I mean so low that the RPM gauge looks like the engine is turned off, although it hasn't completely stalled (yet). The engine will kind of stumble here and there and occasionally jump up to the normal RPM. Not rough really (in fact it's hard to tell if the engine is on when it's so low) but something is obviously wrong. The check engine light is not on (assume no codes?).
Also when I'm driving I can feel that the RPM's are unstable and erratic. You know, it feels like I'm pushing and releasing the pedal very slightly even though I'm not moving it.
I replaced the spark plugs and fuel filter since they needed to be done anyway. I checked the vacuum lines and they all seem good. I replaced a few deteriorated lines even though they were holding vacuum. None of this changed anything.
So now I'm looking at more expensive stuff like the throttle position sensor, idle air bypass valve, EGR, MAF, etc. Where I should start? Is there anything that I can actually test to see if it's working or do I just need to start replacing parts until I find the problem? I guess cleaning the MAF and IAC might be starting points that don't cost anything (that IAC looks difficult to remove though).
I'm kind of thinking it's the TPS since it feels erratic at speed. However, I have never had a bad TPS cause a slow idle before. I have had it cause rough idle and such but not slow. Can it do that? What about the MAF sensor?
I have a 2001 Escape, V6 engine and I guess it really does not like it when it's cold outside. Usually the car runs just perfect but when the winter arrives and temps drop into the 20s the truck does not want to run idle right when I first start it. I have tried by stating it without touching the gas pedal. And also by pushing it all the way down and then releasing it. I don't know which method is the right one, but it doesn't seem to make a difference. It takes some time and eventually after about 5 miles of driving it will act normal again. What could I do to fix that?
View 9 RepliesI have a 2005 Escape Hybrid. Last summer, the A/C went out, so when in the fall I finally got around to having the cooling system flushed. Did the trick, and A/C works fine. Now that winter's come along, I've noticed an issue with the heat. All fan speeds work correctly, and the dash controls for heat and cold work properly. But what's odd is that I get plenty of heat when the vehicle is at speed, above about 30 mph. As soon as I slow down below that, or hit a red light, there's no heat. The blower just blows cold air until I am back up at speed again.
View 9 RepliesI have a 2005 3.0 front wheel drive Escape that the kids normally drive and recently had a crank over/ no start condition in my driveway. I replaced the fuel pump about three months ago. Turned the key and couldn't hear the fuel pump so I proceeded to check the fuses and relays and everything seemed good. I also checked the inertia switch and it seemed ok as well.
I then checked for power at the harness right above the fuel tank and I had 12 volts on two of the four wires so I assume that I have power to my pump. I then took out the pump and had it replaced it under warranty. So I proceeded to install the new pump and I thought that I would hook the harness back up and just turn on the key for a second to be sure that the new pump is working and there was nothing to be heard. Looking for a wiring diagram/colors of the fuel pump?
2005 Ford Escape XLT (4WD) (non-Hybrid). Our Escape had uneven wear on the front tires. Because the mechanic we've used over the year we've lived here doesn't do alignments, my wife took it to a chain tire place on a Sunday afternoon because they were open. He said the ball joint was bad, so he wouldn't do an alignment and because they were super-busy and short-handed, he asked if we could bring it back during the week for an estimate.
A couple of weeks later I called my guy, who recommended a shop a few blocks over who does alignments, so we took it to him. We told him that the chain store had said about the ball joint. I'm pretty sure that before we took it to him, the car had started occasionally started jerking a bit in a curve, but it's been a couple of months and I only know for certain it was doing it after. (I'm not certain if it was doing it before because my wife was mostly driving that vehicle, then)
The first time it was in his shop, the mechanic said it wasn't the ball joint, but the tie-rod. After fixing that, he sold us a couple of tires and aligned the vehicle. On the way home is when I know I was aware of the car jerking a bit in curves. I'm pretty sure it was jerking in the direction of the curve, but again, it's been a couple of months.
Took it back to him the next day and though we suggested he test drive in one direction which had multiple curves, he said he retightened the tie-rod because one side wasn't right, ran it through alignment again and test drove it in another direction which only had one s-curve.
I want to say it was better for a while, but I can't really swear that to be the case. We've long had an ABS light which our previous mechanic in another part of the country said was the sensor. I had forgotten, but the first mechanic we used here had broken the axle and replaced it at no charge, when he was replacing the alternator.
The alignment mechanic said that we had a bad tone ring and the easiest thing to do would be to replace the axle. A week or so later, I called him and said we were ready to do the brakes, but I have one car and he does many and I wasn't really clear, instead of doing anything with the axle or the tone ring, his shop replaced the brakes.
Somewhere around this time, the vehicle started occasionally jerking to the left. Not in a curve, but in the straightways and the best we can tell, it's mostly when we're accelerating and is most noticeable between 30 & 45 MPH. This may not be entirely true, but it's true enough that we believe it. The "jerk" sort of feels like a car driving through fresh snow "falling" into a rut. It also sort of feels what I imagine a faulty ball joint might feel like.
While it was still more of a minor issue -- it happened more rarely than it's happening now -- we took it to what I'd consider our regular mechanic and got him to replace the axle. I didn't actually say anything to him about the jerking because it was still too occasional and I was hoping it was related to the tone ring. It's now gotten progressively worse and I'm at a loss for diagnosis. You'd think that if it was the ball joint, between the two alignments, the brake job, tire replacement and rotation and getting a new axle, one of the mechanics would have noticed it.
Compounding the issue is the fact that there's two (or three if you count the first guy, four if you count the chain tire place) garages involved. Also, I've done some of the engine work my regular mechanic recommended, so there could be a thing about me getting them to diagnose and then doing the work myself or the one mechanic replacing the axle like the alignment guy had suggested. Who knows. We haven't lived here long, so there's not really a lot of history. All I know is that they all get good Yelp reviews.
Also should probably be factored... the alignment mechanic said he felt vibration around 45 MPH and because didn't think we use the 4WD, he said he disconnected the drive shaft from the CV joint (or something like that) as a means of diagnosis. (If there had been a vibration, we hadn't paid attention to it and he did this at no charge, all on his own) Also, a few years ago, prior to our move, the transmission was rebuilt twice (once under the transmission shop's warranty) and I don't remember what the vehicle was doing, but on a third trip the transmission shop had to do something with the transfer case.
Mostly around 40 MPH -- though it may just be too subtle to notice at higher speeds and we rarely drive this vehicle on the highway, so we're mostly traveling short distances at 35 & 45 MPH -- the SUV lurches a bit toward the left and there's a little jerk in the steering wheel. It really feels like I described, like it's getting caught in a rut. Both the car and the steering wheel jerks to the left side. There hasn't been any noticeable uneven wear over the three months we've been trying to figure this out and the front tires look straight up and down. We also haven't noticed any noise. Not going down the road, not when we turn or when the steering wheel jerks.
2005 Mazda Trib. will not let me shift out of park . It doesn't happen all the time button seems to be sticking . Is it the button or the electrical switch on the brake pedal ? This belongs to a friend of mine and this is the info I'm getting .
View 2 RepliesI was leaving work in my 05 Escape. Started up fine, made it to the other end of the parking lot and it died. Restarted it and made it about 10 feet and it died again. Now when I try to start it, it just make a single click. Tried getting a jump from a friend and nothing but the same click when trying to start it. Lights are bright (haven't checked batt voltage yet, but will tomorrow).
View 6 RepliesIs there a heater core bypass valve under the hood that may be suspect or would a heat transfer door under the dash be the culprit? Engine operating temp seems to be fine.
View 14 RepliesI recently got an Escape and I am having a issue with the cruise control. That being, it doesn't work. The control module under the hood is all hooked up, the linkage the the throttle body and all. No broken cables.
The brake lights work as intended, and only when the brake is applied. On the inside, the dash-light cruise indicator works fine.
I ran the diagnostic by holding the off button and turning the key on. The cruise light flashes and I begin the sequence. I noticed I was pushing the brake out of habit while running the first few tests. They all returned 2 flashes upon completion of the diagnostic. All other buttons were registered.
Now the strange part, when I took my foot off the brake and did the same test, the final result is three flashes of the cruise light. I understand these flashes represent a fault, and I am having a hard time as I cannot find one.
What do these results mean? I'm thinking the brake being applied gives a fault surrounding the fact that cruise is disabled when the brake is applied.
The factory installed passive anti theft alarm keeps going off without external cause. Went to dealership to have them do the scan and all alarms point to the right rear-door. They suggest replacing the latch. This same latch was replaced 13 months ago for same problem. They will not honor the now out of date 12 month replacement warranty. They said they have checked the wiring and all looks OK. Must be the latch. I only have 30,000 miles on the vehicle and this is a rarely used door, yet I have to replace the same latch again?? Can the door ajar module be replaced separately and would it be less expensive to do so?
View 14 RepliesI have a 2005 Escape with about 95k miles that won't crank after sitting in the sun on a very warm day. It's intermittent and might be OK for weeks.
This isn't when the engine is hot - it's when the air temperature is in the 80's+ and the black car is parked in the sun. This is the 1st warm weather we've had in several weeks and right on que, it didn't start this afternoon.
The battery is good and there is not voltage to the solenoid when cranking. I've used 2 sets of keys and replaced the PAT sensor ring hoping it was something anti-theft related.
Today, I switched out each under-hood relay (moved them to other locations) and still nada. Luckily today it's DOA in my driveway but may start later.
So my wife's 2005 escape currently will not start. It was running rough so we brought it in to the shop to have the codes read. There was a bad MAF sensor code so we brought it home and were gonna replace the part the next day. The next day rolls around and it refuses to start. Swapped out the spark plugs which was much needed, replaced the valve cover gasket, which had also gone bad, and put in a new MAF sensor. It still refuses to start. It will turn over, but never starts. Also, the sound as it turns over doesn't sound right. It's hard to explain what sounds off about it, it almost has a "soft" sound to it. I can try to explain better if needed.
View 6 Replies