Ford Escape / Hybrid :: 2005 V4 Will Not Start / Running Rough
Aug 11, 2017
So my wife's 2005 escape currently will not start. It was running rough so we brought it in to the shop to have the codes read. There was a bad MAF sensor code so we brought it home and were gonna replace the part the next day. The next day rolls around and it refuses to start. Swapped out the spark plugs which was much needed, replaced the valve cover gasket, which had also gone bad, and put in a new MAF sensor. It still refuses to start. It will turn over, but never starts. Also, the sound as it turns over doesn't sound right. It's hard to explain what sounds off about it, it almost has a "soft" sound to it. I can try to explain better if needed.
View 6 Replies
Advertisement
My 2001 escape recently decided to act up, it was running rough for a little while and then it died and would only run intermittently after that. I found the #3 coil was bad and the egr valve was broken. I replaced those and now when it decides to run it runs smooth but when you give it has it bogs down and dies and doesn't want to run again for a while. I also put on a new fuel filter and the fuel pump sounds like its running good. I know I'm missing something here but I can't seem to figure it out. Also there are no DTC's at all. I really need this car to be back on the road again.
View 11 Replies
I have a 2007 XLS, 2.3L Auto/AWD. About a month ago it quit running while driving, just shut off. When I tried to restart the dash made clicking noises, fuel pump grunt type noises, cluster stays in drive position even though floor shifter indicates I'm in park. Pulled a code P0606, replaced PCM. It started and ran for 20 minutes, made it about 1/4 mile up the road, shut off again. Now I can't pull a code, dash indicates I'm in drive while vehicle is in park, same noises etc.
View 6 Replies
I have a 2005 3.0 front wheel drive Escape that the kids normally drive and recently had a crank over/ no start condition in my driveway. I replaced the fuel pump about three months ago. Turned the key and couldn't hear the fuel pump so I proceeded to check the fuses and relays and everything seemed good. I also checked the inertia switch and it seemed ok as well.
I then checked for power at the harness right above the fuel tank and I had 12 volts on two of the four wires so I assume that I have power to my pump. I then took out the pump and had it replaced it under warranty. So I proceeded to install the new pump and I thought that I would hook the harness back up and just turn on the key for a second to be sure that the new pump is working and there was nothing to be heard. Looking for a wiring diagram/colors of the fuel pump?
View 2 Replies
Alright I thought changing a fuel filter was fool proof but I changed the fuel filter in my 2001 escape v6. awd and now for some reason it wont start right up like it used too before the filter change. It cranks for a few seconds then fires up and runs perfectly fine it sits for a few hours same issue where as before the filter change it fired up fine every time, what did I do wrong. 2001 ford escape...
View 1 Replies
I have a 05 escape hybrid with 75k on it. there is a slight problem every once in a while when it starts the idle jumps up and down and when it is put in reverse it has no power to move. you have to put the pedal to the floor....there are no codes and ford has had the car for a total of three weeks, nothing found and of course it did not act up for them..
View 9 Replies
My "Theft" light on my 2005 Ford Escape is flashing and I cannot start the Escape.
1. I tried the key that I had been using successfully for the last 7 years. , car did not start, Theft light blinked. ,
2. Tried wife's dealer key, Car won't start, theft light blinks.
3. Tried various things, such as manual locking & unlocking, turning alarm beeping on/off, disconnecting battery, etc. Nothing works.
Called the dealer, they say they know nothing. Must bring car in, they say. Basically I am screwed and now must spend big bucks to take it the dealer because of Ford's software bug.
View 9 Replies
So I am changing my transmission fluid tomorrow and was wondering a few things.
1. I noticed some people pull off the transmission hose to the inlet and keep draining that until its clear. For a drain and fill do you do it like that or just pull the plug and refill?
2. When youre filling it back up you just measure how much you taken out and then fill the rest by the dipstick? Anything else i should know?
3. Since I havent changed my transmission fluid in 60,000 miles. I wanted to do a drain and fill. I was thinking I needed to drain and fill it 3 time to catch up to maintenance. How often would you do it to get it clear? Drain and fill then drive it for a week then drain and fill? Or do it all in one day?
View 4 Replies
Lights come on when the ignition is on, regardless of the position of the headlight switch. They shut off about 1 minute after the engine is shut off. The warning chime dings the entire time until the lights shut off.
I want the light to work with the switch and not come on all the time.
It is not just the daytime running lamps. High beams also work with the headlight switch in the off position, ignition on.
Ignition off, the headlights switch functions as it should.
I bought the Escape about 1 month ago. Dealer purchase so I don't know how to get a hold of the previous owner.
It only has 51,000 miles, very clean and all service records.
View 8 Replies
I am trying to run a power wire through the firewall for an amp. I can't find a place to run it ....
View 1 Replies
Along with a high idle problem that's driving me a little bonkers on my 2002 3.0 V6 Escape, I've noticed that the tranny constantly hunts up and down a little when I'm running about 55-60 mph. Today I got a code P1120. Makes me wonder about the TPS... I replaced it during routine maintenance about a year ago with a unit from carquest, so I don't have the original to replace it with for troubleshooting. Will a TPS also cause a high idle, or are those 2 issues typically not related?
View 11 Replies
I only have one key and 2 FOBs for my 2005 Escape, but I do have the key number (4 digits plus a letter). I understand I need more than one to program another myself. Is there an inexpensive way to obtain/program a backup key?
View 9 Replies
My wife has her 03 escape v6. It has a very rough and low idle. On start up it idles nicely and then the idle drops and pulses if that makes any sense. I've pulled I think its the idle control sensor. It killed the engine as soon as I did. I've cleaned the throttle body.
View 2 Replies
My escape has over 200k miles. My battery light dimly flickers constantly when running. there is also a misfire that seems to correspond with the flicker. the faster i rev the engine, the faster the battery light blinks.
My battery constantly shows 14.1 volts. the battery is new the alternator has been replaced twice in the past 2 years.... I noticed when i use my rear washer fluid, it spills into the car on the passenger side kick panel inside the vehicle.
View 10 Replies
I have a 2005 Escape Hybrid. Last summer, the A/C went out, so when in the fall I finally got around to having the cooling system flushed. Did the trick, and A/C works fine. Now that winter's come along, I've noticed an issue with the heat. All fan speeds work correctly, and the dash controls for heat and cold work properly. But what's odd is that I get plenty of heat when the vehicle is at speed, above about 30 mph. As soon as I slow down below that, or hit a red light, there's no heat. The blower just blows cold air until I am back up at speed again.
View 9 Replies
2005 Ford Escape XLT (4WD) (non-Hybrid). Our Escape had uneven wear on the front tires. Because the mechanic we've used over the year we've lived here doesn't do alignments, my wife took it to a chain tire place on a Sunday afternoon because they were open. He said the ball joint was bad, so he wouldn't do an alignment and because they were super-busy and short-handed, he asked if we could bring it back during the week for an estimate.
A couple of weeks later I called my guy, who recommended a shop a few blocks over who does alignments, so we took it to him. We told him that the chain store had said about the ball joint. I'm pretty sure that before we took it to him, the car had started occasionally started jerking a bit in a curve, but it's been a couple of months and I only know for certain it was doing it after. (I'm not certain if it was doing it before because my wife was mostly driving that vehicle, then)
The first time it was in his shop, the mechanic said it wasn't the ball joint, but the tie-rod. After fixing that, he sold us a couple of tires and aligned the vehicle. On the way home is when I know I was aware of the car jerking a bit in curves. I'm pretty sure it was jerking in the direction of the curve, but again, it's been a couple of months.
Took it back to him the next day and though we suggested he test drive in one direction which had multiple curves, he said he retightened the tie-rod because one side wasn't right, ran it through alignment again and test drove it in another direction which only had one s-curve.
I want to say it was better for a while, but I can't really swear that to be the case. We've long had an ABS light which our previous mechanic in another part of the country said was the sensor. I had forgotten, but the first mechanic we used here had broken the axle and replaced it at no charge, when he was replacing the alternator.
The alignment mechanic said that we had a bad tone ring and the easiest thing to do would be to replace the axle. A week or so later, I called him and said we were ready to do the brakes, but I have one car and he does many and I wasn't really clear, instead of doing anything with the axle or the tone ring, his shop replaced the brakes.
Somewhere around this time, the vehicle started occasionally jerking to the left. Not in a curve, but in the straightways and the best we can tell, it's mostly when we're accelerating and is most noticeable between 30 & 45 MPH. This may not be entirely true, but it's true enough that we believe it. The "jerk" sort of feels like a car driving through fresh snow "falling" into a rut. It also sort of feels what I imagine a faulty ball joint might feel like.
While it was still more of a minor issue -- it happened more rarely than it's happening now -- we took it to what I'd consider our regular mechanic and got him to replace the axle. I didn't actually say anything to him about the jerking because it was still too occasional and I was hoping it was related to the tone ring. It's now gotten progressively worse and I'm at a loss for diagnosis. You'd think that if it was the ball joint, between the two alignments, the brake job, tire replacement and rotation and getting a new axle, one of the mechanics would have noticed it.
Compounding the issue is the fact that there's two (or three if you count the first guy, four if you count the chain tire place) garages involved. Also, I've done some of the engine work my regular mechanic recommended, so there could be a thing about me getting them to diagnose and then doing the work myself or the one mechanic replacing the axle like the alignment guy had suggested. Who knows. We haven't lived here long, so there's not really a lot of history. All I know is that they all get good Yelp reviews.
Also should probably be factored... the alignment mechanic said he felt vibration around 45 MPH and because didn't think we use the 4WD, he said he disconnected the drive shaft from the CV joint (or something like that) as a means of diagnosis. (If there had been a vibration, we hadn't paid attention to it and he did this at no charge, all on his own) Also, a few years ago, prior to our move, the transmission was rebuilt twice (once under the transmission shop's warranty) and I don't remember what the vehicle was doing, but on a third trip the transmission shop had to do something with the transfer case.
Mostly around 40 MPH -- though it may just be too subtle to notice at higher speeds and we rarely drive this vehicle on the highway, so we're mostly traveling short distances at 35 & 45 MPH -- the SUV lurches a bit toward the left and there's a little jerk in the steering wheel. It really feels like I described, like it's getting caught in a rut. Both the car and the steering wheel jerks to the left side. There hasn't been any noticeable uneven wear over the three months we've been trying to figure this out and the front tires look straight up and down. We also haven't noticed any noise. Not going down the road, not when we turn or when the steering wheel jerks.
View 14 Replies
2005 Mazda Trib. will not let me shift out of park . It doesn't happen all the time button seems to be sticking . Is it the button or the electrical switch on the brake pedal ? This belongs to a friend of mine and this is the info I'm getting .
View 2 Replies
My g/f's 2004 Ford Escape (3.0L V6 AWD 112,000mi) is acting up. After a full day of sitting, with the second half of it raining steadily, she was driving her Escape and it was acting funny (miss-firing, she said). The engine light came on and soon began blinking. She got to my house shortly after it started this. We left it and I drove for the day. Later that night, I drove it and it seemed fine. The engine light was on, but not flashing anymore.
The next day I took it my friend that was a Saturn mechanic and now working at a KIA dealership (same owner as the former Saturn and current Buick/GMC and Chevy Dealer). It ran fine for me. So he tries to scan it, his Mac Tools scanner won't read it. The KIA scanner wouldn't read it. I drove it the Ford dealer up the road. They said they couldn't get to it until after lunch, I just want the codes read. They re-iterated, and I told them to pound salt and went to an independent shop where I know a guy. They read it right away for me. "Mis-fire on start-up" & "Cylinder 4 Mis-fire." were the two codes stored. He cleared them.
She got the tune up basics (plugs, wires, air filter, etc) and did the complete tune-up herself yesterday. (I was impressed). She put 94 in the tank and some fuel system cleaner in it as well. She said there's been no change and today I finally saw what it was doing. Sometimes during idling at a stop light, the RPMs will drop to almost zero, the lights dim but so far it has not stalled. It'll do this for several seconds, then correct itself and idle normally.
Currently, the engine light has not come back on. She's thinking coil pack (each cylinder has a coil on these engines) on #4. She wants to switch it out with #1 and see if the problem follows. I think that might uncover the cause, or it could be the battery. It's the original, never been replaced and has a lot of miles on it, but it survived this past winter, without trouble. In my experience, most batteries crap out due to age in the fall when the cold snaps start.
View 11 Replies
I have been having this problem with Gf's car for a few months it is a 06 3.0 escape with 141K on the clock the car seems to run ok except at red lights and when in drive it seems to idle like its just about 100 rpms low when I give it a little gas just a touch it smoothes out. if I put it in neutral the car smooth's out but in drive when you come to a stop light or stop sign you can feel the rough or low idle in the steering wheel. She is nagging me and it has been very cold here in Pa and I'm trying to wrap my head around if it is a cold thing or just a coincidence. I'm fairly good at wrenching and I just need some things to look for as when you start the car up cold it idles fast like 12 to 1300 rpms and then drops to about 900 and in drive it seems like maybe it's about 600 to 700 rpms. but where to start to look Is it a sensor, vacuum leak ?
View 6 Replies
I am finding that after a heavy rain that water is running out of the bottom of all four door drain holes when I open them.I have not noticed this on any other of my previous vehicles.Is it "a" good that they are draining well, or "b" bad that water is getting in in the first place?
View 11 Replies
I was leaving work in my 05 Escape. Started up fine, made it to the other end of the parking lot and it died. Restarted it and made it about 10 feet and it died again. Now when I try to start it, it just make a single click. Tried getting a jump from a friend and nothing but the same click when trying to start it. Lights are bright (haven't checked batt voltage yet, but will tomorrow).
View 6 Replies
