I just put on new winter tires and rims on my 2012 Escape and after driving about 6 miles, the low tire pressure light came on. Is there is a procedure to learn the vehicle to the new tires?
View 6 RepliesWith winter on its way I have installed winter tires and steel rims w/o pressure sensors on my 08 Escape. Is there a way to disable the dash warning light for low tire air pressure?
View 14 RepliesHow do you reset the tire pressure sensor 2013 Camry. Could find the reset button.
View 5 RepliesThe facts: 2009 4x4 V6 Escape with Valve stem mounted TPMS
I am getting a tire pressure sensor malfunction fault. The warning light is on and the error message is displayed on the little screen in the gauge cluster.
What I have tried: First I should say I have replace to defective sensor twice now...
1) I put the escape in tpms train mode by hitting the hazard switch off/on about 6 times.
2) I used the train tool to train all the tires but there is one that is giving me trouble and will not train.
3) I tried deflating the problem tire and inflating it to the specified pressure given on the be pillar of the escape (30 psig)... after inflating it I tried to retain it with no luck.
4) I tried rotating the tires and as I mentioned earlier I have replaces the problem sensor twice. Still can't can't get the problem tire to train.
My thoughts:
1) I don't think this is a module error because I can train the other tires and since I rotated them I know their position is not a factor.
2) its possible that I have got two defective tpms sensors but I think that is unlikely.
3) I have read of another procedure to put the escape in tpms train mode that requires you to turn the ignition on/off, step on the break pedal, tap your head and rub your belly, etc... but I have not tried this method. Is there a difference from this train mode verse hitting the hazard switch on/off about 6 times?
4) Does the train tool only work on previously trained sensors? do I need to register the new TPMS sensor with the TPMS module? I have an OBDII tool that connects to scanXL software on my laptop which included the ford proprietary protocol. I looked for a way to program a tpms sensor (similar to how I did it with my toyota) but couldn't find the option.
Over the weekend my 2008 Escape Hybrid manifest 2 problems the same day.
1. The remote keyless entry button stopped working (thought it was dead battery in key)
2. Got a error message 'Tire Pressure Sensor Fault'
So after suffering with having to actually unlock my car with a key (heehee/see sarcastic grin) and getting irritated by the error message. I asked the internet about my symptoms. Got the standard answers of "bad tire pressure sensor/reprogram" and change the battery in the key. But ONE and only one person (namely Enviroguy ) said what I thought was going on - that these two problems were related. (afterall it is 2 wireless devices in the car.)
Changing the key fob battery had no effect & Both keys were unresponsive. Seeing what Enviroguy said about certain chargers or wireless devices can cause interference in the tire sensor and keyless systems. .... Then I remember that I had been using a new no-name charger for my cell phone when this problem started.
I unplugged that charger.....(it was a cheap generic power point to USB adapter). The Keyless system is working... ! The tire pressure error has vanished.... !
I did not go to the car appointment.... Now let's hope this was in fact the problem! May my 2008 Ford Escape Hybrid "Be Healed!"
I realize that is vague. I realize it could be anything from a wheel bearing to a ball joint, tie rod, control arm/control arm bushing, etc.
Are there any very common front-end steering or suspension issues on 2012 escapes? When tires are inflated to 32-34psi, the car tracks straight, gets great mileage --but almost sounds/feels like it's got a CV or wheel bearing issue on the front right. Every time I hit the brakes while backing out of the driveway I can hear a slight bump or pop. When the car is parked (flat, tires straight) there is slight play left-to-right in the steering wheel.
I'm a German car guy. Have never touched this car. (Wife's car) Right tire is wearing bad on inside. Looking for some direction so I can assess. Car has 88k miles. This will be a DIY fix. Don't have any manuals or anything so just looking for a heads up where to start. Also is Haynes the best way to go? Is there a Bentley? Anything online/CD/DVD?
Play in steering wheel makes me think tie rod (fine because easy/cheap) but such excessive wear on the inside right front makes me think wheel bearing. Could it be both? This is AWD. Is this (like a Subaru) a CV joint where the front spindle passes through a strut base that everything attaches to --so there's an inner and outer wheel bearing?
Does anything up front require a press or can it all be done without a press?
My low tire light is on my 2009 VW Sportwagen SE 2.5. The tires are inflated properly even the spare tire and yet the light is still on.
View 1 RepliesI'm having an issue with my ford again. Escape, V6, 123k miles. Recent work done: Replaced all spark plugs, coils, and intake manifold gaskets. Replaced all four O2 sensors. Oil change switching from the 5w-20 to 5w-30 due to it getting cold, (probably a month ago?).
Now for my current problem. Two days ago on a 20* morning, after it sat outside all night, I drove about 3 miles and then noticed the oil pressure light was blinking intermittently. When I came to a complete stop, it stayed lit. I pulled into a parking lot and starting shutting stuff down. I noticed when I turned the heater blower off, the light went out. Turning it on to High, I noticed the RPMS on the tach dropped to around the 500 mark, and the oil pressure light came back on. I turned it off and let it sit for about 45 minutes. Oil is showing good on the dipstick. I then drove it the last two days without the light coming on.
Now this morning, driving it again in 20* weather, after it sat outside, the light came on again, in almost the exact same place away from home. Both times the motor had reached operating temp, with the temp gauge being in the middle between "C" and "H". This time, even with turning the blower off, it came on every time it was at idle. I let it sit another 45 minutes, but this time when I drove it, the light was more intermittent and then was constant.
Again, the oil level is good on the dipstick, and the motor seems to be running smooth. I'm wondering if this could have anything to do with changing over to a different oil and with it being so cold in the mornings?
I have it written down at home, but I can't remember when I did the actual oil change, but its probably been a little over a month. I went from 5w-20 Pennzoil, to 5w-30; wix filter. I'm planning on doing another oil change tomorrow when I get home and go back to the original 5w-20. Also, I'm ordering a new oil pressure sensor, and I'll try that also. I've also looked into an oil pressure tester....
2008 Escape V6
Got the oil changed at Walmart and they told us there was oil in the air filter and we should replace the pcv valve. Before we changed it the oil pressure light had started coming on when the car is stopped, either in gear or park. Once the gas is hit it goes off, even at something like 1 mph. Well I changed the pcv valve but the oil pressure light is still doing the same thing. What should be my next step?
My friends 2006 Escape has the ( low pressure warning light) flashing on for about 10 seconds after starting the engine. All tires are at correct pressure. What is causing this?
View 5 RepliesIs there a reset to the tire pressure warning light? I filled all 4 tires to recommended pressure and the light is still on.
View 3 RepliesFirst cold day of the year today and naturally my TPMS light came on. Checked the pressures with my own gauge, all at 34 psi. Inflated them all to 38psi and the TPMS light is still on. Drove a little ways - still on. Checked pressures again - still 38psi. I had this happen once before in mid-winter two years ago and I can't remember what I had to do to reset the TPMS light. Mine isn't one of the ABS/ESP systems so I don't have a reset button - I need to do something with the VAGCOM but I don't recall what.
What's weird is that the TPMS threshold should be 7psi per wheel shouldn't it? And my light came on when it was only 4psi down. Is there somewhere I can check and find out what the ECU thinks the threshold is - again with my VAGCOM?
2010 Tiguan 4MO
n the 2012 Prius how would you reset the low tire warning light once the tires are brought up to proper pressure?
View 8 RepliesSo, I seem to have horrible luck with valets. One curbed my wheel a couple weeks ago. The TPMS light came on and all tires were equally underinflated... I thought it was due to a recent cold snap. Well, once I got around to inflating, I noticed the curbed wheel and the sidewall bulging tire. Nonetheless, i tried to reset my TPMS light and there is no button in the glove box. I have a thing that should house a button, but there is nothing behind it. Is this usual?
View 4 RepliesHow is the oil change reminder reset? Also how is the computer reset for a new new battery?
View 8 RepliesI just bought a 2008 Highlander. I'm thrilled with the quality of the vehicle so far. This model has a tire pressure monitor system which I can't seem to reset. I've set the pressure in all tires at 34psi and 44 for the spare, and the indicator light will not go out. I press the reset button and the indicator light never blinks to indicate that a reset is in progress.
View 29 RepliesI took my truck in because the tire pressure monitor light was on. I tried resetting it and that didn't work. I took the truck to the tire store where I purchased the tires. They checked all the sensors with test equipment and 4 out of 5 were bad. So I had them replace all the sensors including the spare. The light is still on. I followed the reset procedure and confirmed all 5 tires were at 32 psi. when I perform the reset the light blinks once and then stays on. What Now?
View 1 RepliesHow do i reset tire pressure for my 2007 lexus gs350, i cant find the switch or any other option ?
View 8 RepliesI want to not only upgrade to LED lighting, but I want to add to the single bulb fixture found in the center dome light (between the front and rear seats).
I can get the cover off OK, but I'm having trouble figuring out how to remove the fixture itself. There are what appears to be press fit style plugs (similar to what you would expect in a door panel) but there is also half-slots making it look like one side pops out and the other side slides off the mounting plug.
How to remove it without breaking it?
My 2008 Ford Escape is stuck at 5% Oil Life I have tried the reset procedure But when I press the 3 buttons Setup Info or Reset nothing changes It will not change screens When I start my car I see the KM (I'm from Canada) then within a couple of minutes it shows %5 Oil Life and no matter what I do it wont change or scroll to a different screen. When the door is ajar or tail gate open it shows but then will flash back to the 5% Oil Life
View 8 RepliesSo I just got my new wheels today without sensors. The light was on after driving awhile. How to reset the light? I did try step by step in the manual book but didn't work.
View 2 Replies