99 escort 2.0 will not start. Has spark, fuel pressure, and 100 psi compression in each cylinder. After cranking for awhile , pull the plugs out and the plugs are wet with fuel. There is no answers anywhere on the net, but apparently there are others like this out there. No codes also.
View 1 RepliesA friends car broke down. He has a 1990 ford escort. It would turn over, but would not crank. I took a look at it and the timing belt was off. Replaced it today, and the car is still turning over but not cranking. The timing is set right, its getting gas, and its getting fire. What else could be causing it to turn over but not crank?
View 19 Replies1999 Savanna 1500 van. This has been a great Van, only has 70,000 miles and has never let me down until a few months ago in February when it was getting down to -20 degrees F. Seemed like it was cranking fast so I thought it was timing. Turned out there was no fuel pressure so first put the relay in, that didn't work so we dropped the tank and put a fuel pump in. This seemed like it cured the problem but I only drove it 200 miles until mid May when it did it again.
The security light wasn't staying on so we thought it must be the ignition switch. That didn't fix it either, we just got the ignition switch back together (not the actual switch but the wiring harness) and it's not starting again. It will start after some anguish and cursing at it. Seems like messing with the wires going to the fuel pump or hitting the cover over the fuel tank will cause it to start. I haven't checked it yet but I can guarantee it doesn't have any fuel pressure.
I want to change the spark plugs and wires in my 1996 Ford Escort (1.9 Engine).
The problem is trying to remove the No. 1 spark plug boot and spark plug. Both are located behind the alternator and are difficult to get to. I tried a boot puller but could not get easy access to the boot to pull it off the spark plug. The other three boots and spark plugs are readily accessible.
Is it sufficient to place the dielectric compound just inside the opening of the boot before placing it back on the spark plug, or should it be placed on the metal clip that is ~2-3 inches down inside the boot?
I have a hard starting condition after warm up. It starts up fine when it is cold.After running diagnostics and coming up with no error codes, I noticed that I smell raw fuel after the car was warmed up and sitting for about 15 minutes. I believe this is the cause of the hard starting condition after warm up.
How do I test the fuel injector for leaking? I think it may be leaking fuel into the throttle body after sitting for a few minutes, causing a rich or flooded condition which makes it difficult to start after it has been warmed up.
1992 GTS ... Code 12 (ignition). My car started misfiring and now it won't start at all. Just checked all four cylinders for spark and they have spark. I can also see/smell fuel on plugs when I pulled them.
View 2 RepliesI'm gonna change plugs , hoses, belts and fuel filter on my 08V10. Hoping it works with the mpg.
Anything else I should look for or do? Is there anything I need to know about changing the fuel filter?
98 Passat 1.8T FWD
Car will not start. No sound from fuel pump while cranking. Pulled up the carpets and pulled the cover and connector from the fuel pump. Ive heard the relay is the common problem. I tried checking the voltages on the harness and we get 0 while cranking. Pulled the relay and we get a resistance from T pin to pin 86. I did notice a yellow color on the white connector on the fuel pump itself around the middle two contacts.
I have a 1999 Ford e350 7.3 powerstroke with 140000KMs on it.
The truck cranks really well but it just wont fire off, not even with a shot of starting fluid.
I recently changed all 8 glow plugs, fuel filter, fuel, oil and I keep it plugged in, my last mechanic told me the engine is toast and it cant be fixed.
I have a 1999 Ford Escort SE wagon with 112k miles on it. Last week when leaving work my car started very rough. This was unusual so I killed and restarted the car about three times before letting it run it's course (~30 seconds), after which the car ran fine. About a week later on my way to work the car seemed to 'sputter' (for lack of a better word) when I pushed down on the petal looking for some power on two separate occasions. On each side of the sputters the car seemed to respond fine, but when it did sputter there was a severe lack of power. I got to and from work just fine, but while letting the car idle in the parking spot of my apartment for a minute before shutting off the engine the check engine light finally came on. The following morning the car again started rough (as if it were misfiring/running on 3 of 4 cylinders) and this time it took a good minute before smoothing out. However, after the car smoothed out I experienced no issues on the way to work, no sputtering, no loss of power, nothing. Doing some initial online research I feel that the problem may be one (or more) of the following:
-Fuel pump
-Vacuum lines
-O2 Sensor
-Spark plugs (they are original)
-Fuel Filter (it is actually past due for replacement)
I plan on getting this checked out ASAP, but that still may be 2ish weeks away with my schedule. Some similar reports say that I may be having a 'lean mixture' issue (not getting enough fuel), but I haven't had the time to check the code. My question is, how "safe" is it to continue driving my car with the current situation? Is it at a super high risk of failure/random stalling during rush hour? Will it cause any damage to the engine if there is a cylinder misfire upon start up? I was also wondering if the car would be reasonably reliable to drive on a ~400 mile road trip on an upcoming weekend, but I am making plans as if it is not.
Additional Details:-Tried charging the fuel lines (car to 'ON' then 'OFF' position 3-4 times), had no effect on the morning start-up-Commute to/from work is about 20 miles
I replaced the glow plugs and gpr and the truck won't start. I'm also having to replace the water fuel separator. What is going on? 1999 F250 7.3l ....
View 10 RepliesBought 02 350 DRW, started hard first day, now not cranking. Seen a post on neutral transmission switch and mine is not lining up, but need to adjust the rod out of transmission also? I was able to match lines on switch but with flanges on fitting it will move back out of place when moving it to fit in bolts.
View 4 RepliesThis morning I went to start her up, and she fired right up and I let her warm up until oil temp got to 100F, when I realized that I wasn't leaving right away so I shut it down and came back about an hour later. Oil temp now at 78F, but she wouldn't start. Have Torque Pro running, and the IPR is going straight to 98.6% every time while cranking, sits at 14.7% with KOEO.
Truck's been running fine, recent oil/filter change (T6 10-40W), cleaned & re-installed CAC tubes/boots for leaks. All else seems good. Pulling the ICP sensor shows HPOP going to 2800psi, with IPR @ 30%, still no start and not even a cough.
The IPR is original, rebuilt once several years ago.
My 99 b2500 4 cly shut off on the road this morning and now will not start. She'll turn over just fine but no sputtering or almost-starting. The engine light isn't on when i try to crank it. Any deductive checklist so i can start narrowing down the problem?
View 14 RepliesI'm in a real jam because my work truck won't start. 1999 F250 7.3 Diesel 157k mi. - Air and fuel filters were replaced in the last 500 miles. This pup ran fine when I parked it last Wednesday before the holiday.
Checked for start last night because I'd been having battery issues, Both were replaced the previous week. It's cranking good but just won't start, not even a bit. No wait to start light, oil level is good, can not get obd reader to link.
Was driving to work about 4 miles into my travel rolled around corned and she died..... tow bill and cps she fired rite up. Ran at idle in drive way because I was a little leary for about an hour left drive way went 2 miles went to pull in to store died again. Another tow bill and 2 more cps still won't start rpm is only like 200 when cranking but sounds like a lot more. The wts light works, batteries are pretty new, cps in new...
View 6 RepliesI have a 2003 F250 with 157,000 mile. Left the house last week and got about a mile down the road when I realized I had forgotten something. Pulled off to turn around and had no power to get back onto the road. RPMs wouldn't go over about 1500. Finally got it on the road and it completely shut off. Was able to get it home and have been tinkering with it. Stats from Scangauge are as follows:
Key on not cranking.
IPR 14.81%
FICM 47.6-48.0
Sync=0
ICP 32
Data while cranking.
IPR 43-47%
FICM 38-42
Sync=1
ICP 1532
I'm leaning towards a bad FICM but the ICP pressure seems to be high to me.
I recently replaced a bad head gasket on this car. After putting the reworked head back on the engine and putting everything back together, I can't get fuel to the engine. I cheated and took the intake manifold out and bolted it to the head and then set it back in the car plugging my injectors back into the manifold once in there. I checked all my electrical connections and they are all good. I am not getting power to the fuel pump, which was replaced a year ago when I first started tinkering with fixing the car. I get power to and from the inertia/fuel cut-off switch, but it doesn't appear to get to the fuel pump. I checked all the injectors to make sure they were seated properly which they were and all the fuses both under the dash and hood that I know about and then some. When I pull the 30amp fuse under the hood, and replace it, I do hear a sound that sounds like something is pressurizing or pumping for a second or to, but the sound is from under the hood and not from the pump/gas tank area.
View 2 RepliesI have a 1999 f250 7.3 psd. it cranks and will not start, it use to crank for a bit of time and then start and now it refuses to start. If I leave the key in start position for like 30 seconds it use start and now it wont. I am thinking it is something with the glow plugs?
View 8 RepliesBackground on the vehicle, Last week installed Swamps 200cc/30% injectors with a 38r. Had swamps reburn my chip for the new upgrades.
But heres the problem i noticed starting the truck was a little harder ( longer cranking ) till it would start never thought of anything since i read air gets in and can cause it but then yesterday and today its taken 30 minutes to start the truck since i have to do a trial and error.
The truck just seems like the batteries are being drained or something along those lines. i also noticed my gauges keep resetting back to blue( default color). Today I plugged a battery charger up all good voltage i charged them so both read 14v and still no start. So a couple of attempts at starting with chip in and ICP on nothing
I unhook the chip and ICP get a half start then eventually it starts. After then i can hook it all back up and it starts good for the rest of the day but for what ever reason after it sits all night it doesn't want to start up right away. I'd like to figure it out today since id rather not wake up at 4am and attempt to do this all before work each day.
I noticed that my gauges would reset to the default color after each turn off. So i unscrewed my ECU and then redid that to make sure its tight. along with making sure the chip is seated properly. after that it stopped resting my gauges. Whether that's the issue or not i cant say but ive been checking my HPOP oil level since i stopped driving it around 1400. and hasn't changed oil levels are good. I plan on starting it before I go to bed around 2200-2300 just to check and see what happens.
This is kind of strange, I have a hard start problem, when I crank it the first time, it fires immediately, kind of like a romp, but doesn't start, then when I crank again I get a lot of whitish smoke and no start. I read to try and unplug the ICP and try it. That worked, and I had oil in the connector. I replaced the ICP, but have the same problem. I still have to unplug the ICP for the truck to start. When it does start, it runs great! No injector stiction, no smoke, no rough idle, it runs and sounds great. Why unplugging the ICP is still required to start? (Only after sitting for more than 10-12 hours).
View 9 Replies