Ford Excursion :: 2000 FWD - O/D Light Flashes - Tranny Shifting Hard Then V10 Dies?
Oct 31, 2014
OK, so my 2000 FWD 6.8L Ex has 128k actual miles on the odometer w/ a stock 6.8L from a wrecked later model truck with ~115k actual miles on this 2nd engine from what I was told by the PO/2nd owner (I have no reason to doubt him and I verified the history with the original owner). So I'm guessing that the 4R100 is original without having ever been rebuilt.
I've had zero issues with the drivetrain up to this point, this truck has always run like a top and been very reliable. This afternoon in drive time traffic the overdrive light started flashing and at the same time I noticed that the transmission was shifting really hard (snapping into the next gear) and not in a good way. I was in stop and go traffic when it was shifting weird like this. At one point I make it up to 55+ and I noticed that the O/D light had quit flashing and now it was shifting like it normally does. Then back into stop and go driving the O/D light starts flashing again accompanied by the weird hard shifts.
Next thing I'm sitting there with my foot on the brake fully stopped waiting for traffic to start moving through the traffic signal when out of nowhere and no indication of anything being amiss the engine quits and I get dash lights including CHECK ENGINE and THEFT. I cycle the key off and then try to restart it. It took nearly 10 seconds of cranking to get it to start up however once started everything is back to normal and I have NO trouble lights illuminated including no O/D light and it's back to shifting normally. I continue on in stop and go and highway speed driving for the next 15 minutes like nothing ever happened, transmission is shifting like it always has. The truck has been turned off once and restarted since that incident, yet no other indications of any issue. What's going on?? What to check into?
View 14 Replies
Advertisement
My tranny guy just did a full scan and the ONLY thing which indicated a problem was 'output speed sensor' which we were able to trace back to most likely being caused by a completely hosed driveshaft (I've noticed a driveline vibration). We're going to install a new driveshaft, replace the output speed sensor(s), check for any frayed/chaffed wiring going to the output speed sensor(s) and then see where that leads us (he said something about some computer module in the dash which he's had to replace on several Sooper Dooties).
View 7 Replies
I have a 2001 3/4 pickup. Sometimes the over drive light flashes. When it flashes it shifts really hard and sometimes it won't shift into 4th until I mash the overdrive button. Sometimes the light doesn't flash at all and it doesn't have any trouble shifting at all. Is it a solenoid? Or wiring issues?
View 6 Replies
I have an '03 w/ the 7.3L. Today the tranny stopped shifting up out of 2nd. And the O/D light flashes. There are no other MIL lights on. I have do some searching here and some say the VSS (Variable Speed Sensor) is bad, some say there is a connector on the passenger side that needs cleaning, and some say there is a solenoid just inside of the tranny bottom that needs replacing. So, what shall I do?
View 4 Replies
I have a 2000 V10 2WD Excursion with 104,000 miles. Last week it started shifting hard between first and second, but only when I am between 1500-2k RPMs. If I rev the engine higher, it shifts smooth. I checked the fluid and it is fine. I rarely tow anything except my little trailer to the dump every few months. I have a few questions:
1. Should I drop the pan and change the tranny filter?
2. Should/Can I check the rear diff fluid? (haven't noticed any leaks)
3. Could an inline flush and fill work?
4. I saw a post about a speed sensor in the rear diff. Could this be the issue?
View 4 Replies
i have a 2000 ex,6.8 4x4.every now and then the dome light stays on.theres also a problem where theres a buzzing sound coming under dash while driving and makes the dome light flicker.these are seprate problems.lol.when the buzzing sound is present ,it stops when i open the door,running or not.but starts up again when i close it,even happens occasionaly when ignition is off and no key in ignition.electrical problems are my worst night mare!!!!!!!! My battery is dead in the morning when this is happening .oh yea,and the o.d.light flashes occasionaly as well.im totally lost.
View 6 Replies
So I have a 2000 6.8l V10 that I recently swapped the engine on (reman). While I was doing that, I decide to do some LED upgrades. I swapped out the turn signals, side marker lights, and headlights with LEDs. I added some LED fog lights, and I have a Rigid light bar.
I replaced pretty much everything on attached to the engine aside from the alternator (it didn't give me any problems, so I figured it was good).
When the truck is running with the lights off, there are 6 LED strips running as DRLs, when the lights are switched on, the side marker, turn signal and headlights turn on. When I switch to high beams, my fogs turn on. The light bar is on its own switch.
During the day with the headlights off, I dont notice the battery/charging system indicator light turn on at all. At night, when I flip the headlights on, I've noticed that it sporadically and randomly flash. The flashing indicator light does not appear to be associated with bumps or anything.
It does not seem to matter if I have just the DRL/low beams on, DRL/high beams+fogs, or DRL/high beams+fogs + light bar on. The indicator light comes and goes with the same random consistency regardless of how much power I am sucking from the alternator/battery. The RPM's of the engine also appear to have no effect on when/how often the indicator light comes on...
I drove for over an hour last night, and the voltage gauge never changed, so the battery does not *seem* to be draining (~1 year old Optima yellow). I added an extra ground wire going from the battery to the engine about a year ago (long before this LED upgrade) to ensure a good ground, so I dont *think* the wires are the issue. Is my alternator suddenly going bad? Any higher output ones I could replace it with? Is it a simple fix that does not require a new alternator?
Here are some pics of the lights:
(This was before the fog light install)
These lights only come on when the truck is in reverse:
View 6 Replies
2000 X V10 4WD... 178K. Truck was not well maintained for most of it's existence. Drained both the TC and Drain pain and replaced the oil filter. Tranny oil looked like crude and a lot of tiny specs of metal - it shimmered in the sun... needless to say - I'm pretty sure it had never been changed.
Now - issues since I've gotten it done... Tranny has been slipping... I figured that I may not have filled it enough and after adding a few quarts, it seems to have stopped. Slipping was initially just when going from a stop.
Now it's having a problem where the engine dies when I shift from one position to another... For instance - from Park to Reverse, the engine RPMs drop as the clutch engages - but they drop from about 900 RPM down to about 500. And 50/50 chance the engine dies. Going from Park to Drive, the same thing but maybe drops to about 700 RPMs. Tried it in 2nd and 1st gear. Has happened in both. I've tried shifting to OD first before going to 2nd to 1st or vice versa and seems to behave better.
Should I flash the ECU and have it relearn the shift points? Did I overfill? Between the TC and Drain Pan - about 16 qts came out. I've been checking the dipstick - no frothing or bubbles. When running and in park - it actually shows low. Seems to drive fine once it's on the road. The engine cutting off when it's put into gear is really unexpected.
View 13 Replies
Having this issue for a while. Finally have time off work to dig into it some more. 00 ex, v10. Intermittently flashes o/D light and shifts hard. I replaced 2 out of the three speed sensors. One at the output and the other on the axle. Only active code is the p0720 output shaft speed sensor circuit. Last weekend removed and inspected harness, did not electrically measure it tho. My question is: intermittent problem? I drove it today to see if it was still doing it and it drove like a dream! Haven't had the battery disconnected or anything, just sometimes it does it and other times it a smooth ride.
View 14 Replies
Pulled the codes and erased them a few days ago for the first time and now it's about a once a day thing. I can drive for 2-3 stops and then I come out of a place, get in the truck, and when I start it up I have the light and the OD flashing.
View 14 Replies
My problems started out around the beginning of the year. Mostly, it was the transmission. It would slam really hard when shifting. Worst, sometimes while on the freeway, it would shift on it's own, for no reason, into a lower gear and get stuck. (Happened twice and was really scary).
Along with this, a couple times I would start it up and it would rev really hard, about twice what it normally would.
Usually, with the revving, I could turn it off and back on, and it would stop. A few times I could disconnect the battery, reconnect, and it'd be fine.
As for the tranny, I could turn it off then back on and sometimes that would work. Other times after a few miles it'd work itself out.
I did take it to my local Hyundai dealership. The first few times they couldn't get any code to pop, and they couldn't simulate the issue. It was very random when it'd happen. Luckily, on the 3rd try, they did get the tranny to shift hard. They said it was a bad tranny and replaced it (free due to warranty).
Unfortunately, that hasn't gotten rid of the issue. After a few months... maybe 3K - 4K miles the issue is back. Again, it's very random.
I've had the high revving which I've had to disconnect the battery to resolve. And the tranny is slamming again.
I don't notice any other issues. No engine light (except the one time the engine was revving really high and I had to disconnect the battery to reset, then the light went off).
Sometimes I can go a month with no issues. Sometimes it'll happen back to back days.
Could it be a computer issues? Is that something I can fix/change out as a novice?
View 10 Replies
My tranny started acting up so I took it to a reputable transmission shop for repair.
Symptoms : Shifts very hard 1st to 2nd. Light flashes on overdrive button.
The following is what has been done at the transmission shop.
Computer failed to read codes. Sent out to rebuild. After rebuild, codes read FIPL needs replace. Done and gives good readout. Trans control replaced, speed sensor replaced, checked all associated wiring and plugs as well as ground. Dropped pan, changed fluid and filter. No parts in pan. Tech says pan and fluid looked good. Replaced coil pack.
After all that, this is what is happening..Clear all codes. FIPL reading good. No flashing light on shifter. It feels like it is shifting from 1st to 3rd, then back to 2nd. Still shifting hard and indicator light starts blinking again. He is going to read computer again. At this point, he suspects a mechanical problem in transmission but is reluctant to remove and tear down.
View 7 Replies
the truck has a few problems however nothing that I cannot be fixed (I hope). It has low miles, and I think I know why.
(1) I found out today that if you turn hard to the right the motor shuts off. ...It restarts easy.. . It will not do the same on left turns ..
(2) the Elect windows still go up and down at anytime after you cut the motor off and pull the key...
(3)The AC cuts off and will not restart..(the PO has replaced the low pressure switch) however I found that power is going to the clutch. I taped the clutch and it pulled in....If I remeber right it was spoken somewhere the one could pull the clutch and remove a washer...Is this true, and is any special tools needed?
View 13 Replies
I recently bought a 2002 Accent with the 1.6 auto 133000 miles. I have been reading the postS around here about the crappy transmission. My car seems to have some life in the tranny still but it has slipped from 3rd to 4th gear around 45 mph when i get on the gas too hard. Its also a little sluggish to start off. My question is should i change the fluid out knowing i have a slipping issue? The reason i ask is that last time i changed the fluid and filter on a Jeep that was slipping i ended up having to rebuid it. Is that a real possibility if i change the fluid in this Hyundai?
View 3 Replies
Today i go out and crank my truck and it fires right up. I notice the overdrive light on the shifter is flashing. It did that a few days ago but stopped within a minute or so. This time i noticed the check engine soon light was lit as well. I checked my scan gauge and it said three codes stored. The first one i looked at was P0705. The truck was running fine the whole time. I turned it off and tried to crank it again.
This time it just turned over and over but would not crank. I cleared the codes before checking the other two codes. I wish i would not have done that but I wasn't thinking straight. I tried several more times to crank but it never fired. One time it tried to but never fully did. I gave up and switched cars. I am going to try again when i get back home. What causing this?
View 14 Replies
Im having an issue with my 2000 f250 7.3 diesel. 4x4. The od light is flashing and the tranny is kind of jerky when it shifts. Also my truck won't go into 4 low. (I have shift on the fly) and every time I put it in park my truck revs up to 2000 rpm for a few seconds. I do have a ts 6 pos. Chip with can tunes on it. And I have already replaced the IPR. It does it even in stock setting.
View 1 Replies
I have a 2000 excursion V10. It will die in gear forward or reverse the overdrive light flashes and cel shows code p0720. I have new plugs and COP on all 10 cylinders. I have replaced the differential speed sensor and the sensor on top of the transmission. I have a basic code reader it shows at the time it dies the vehicle speed is 70 mph while the speedometer shows 0. When I unhook the abs module it still has code p0720 but it does not die. I am replacing the abs module?
View 8 Replies
2006 E-350 Dually Ambulance Chassis with the 6.0... Approx 125000 miles.
Recently, the truck started an issue. its an every once in awhile thing but has been doing it more recently. The OD light will start flashing and the vehicle will start to have clunking in the tranny and start shifting rough. ABS kicks in making it hard to stop. Once you turn the truck off and back on, Its fine until it does it again. Im connecting to a scanner tomorrow to see if i get any codes.
View 14 Replies
Ok, I have a strange no start issue right now. My excursion won't start. I have power to everything and both batteries are at 12 volts or a bit more but the starter won't engage. If you turn the key to start all that happens is relays click under the dash and the airbag light flashes. It almost seems like the transmission is in gear. It did this twice about a month ago and has been fine ever since until today.
View 8 Replies
My son in law's 2004 F150 had been having a random hesitation and dieing on light acceleration. Now it is every time he drives it.Here is the scenario. After taking off from a stop, with light acceleration, when speed reaches 22 mph in drive, it is like you turn the key off,,,except all the gauges still work,radio air all electrical seems to stay on,BUT the indication lights on the dash and the small red anti theft dash light for the security function comes on. If you try to continue accelerating, the truck will die, but if you let off on the gas and then continue to accelerate all is well.
I tried starting off in 2nd thinking it is a transmission problem same scenario except truck did get up to 29mph before experiencing the dieing issue. Tried starting off with Overdrive disengaged, same problem. The truck is throwing no DTC codes and Ford says unless it throws a code, they can't work on it. Truck runs great at highway speeds . My son in law says that if the truck does die,(by trying to force acceleration) he has to stop, and put the truck in neutral or park, and then it will restart. I have checked all connections at the transmission, rear end and all sensors/controls, but no solution. We are getting desperate and don' t know what else to check. It has the 5.4 engine.
View 6 Replies
I have a 2000 Ford Ranger 4X4 XLT with a 5R55E automatic transmission.
Coming out of a stop the truck jolts at about 20 mph as it shifts from 2nd to 3rd gear. It feels like it revs too high in 2nd gear, up to about 2400 rpm, and then shifts hard into third. It feels like the truck gets a gentle hit from behind.
Earlier in the week, the O/D light flashed. I took it immediately to an independent tranny shop who pulled the code for me: P7033, incorrect ratio in 3rd gear.
They cleared the code for me. In limited city and highway driving (less than 15 miles each trip) the O/D light has not flashed again. But the problem remains. I plan to take it back to the shop later next week.
What might cause this so that I might have a more informed conversation with the tranny mechanic?
View 3 Replies
