The backup alarm sounds when I put the truck in reverse when there is nothing behind me. I found posts about people not getting any sound at all but none like mine. I'm guessing I have at least bad sensor that 'thinks' there's something in the way when there isn't.
View 5 RepliesMy back up alarm hasn't been working all the time. I checked for the clicking sound when it wasn't working & could hear the clicking. The light is on all the time when its acting up. Is there a control box somewhere?
View 9 RepliesJust started doing this. Sometimes I can get them to turn on in I hit the button enough. Switch going bad?
View 12 RepliesMy reverse camera goes over the mirror, its a mirror when not in use and a camera when in reverse. The way this one is set up, the camera taps switched 12 volts at the rear of the car (tapped trailer connector for these) and the video signal runs forward (ran under headliner to center console to mirror). The monitor needs 12 volts, ground, and + 12 volts when I shift into reverse. I just read a half dozen threads where people suggested tapping into a black wire with pink stripe in the driver's kick panel. Just checked, no such wire on mine. I do not want to run a wire back from the taillight, this seems backwards since the power goes from the front of the truck to the reverse light in the taillight I just need to find the right wire. I checked the reverse relay and the fuse in the fusebox and they are both 12 volts when the truck is on, so they must be prior to the reverse switch.
View 14 RepliesAs soon as I put my truck in reverse, the alarm goes off even if nothing is near me. This just started a few days ago/
View 4 RepliesMy reverse lights and back up alarm will not engage unless i hold up on the shifter while in reverse the only thing i found was a adjuster for the indicator....
View 14 RepliesI've seen this talked about before and it's happened to me before as well but now the tranny is leaking onto my Ypipe a couple times per week and it's giving me a hard time when I try to reverse. revs drop and it stalls if I don't give it enough gas.
So I know I have to change the seal but Ford is telling me the torque converter will need to be replaced but another transmission shop told me once the seal is changed and fluid level set appropriately I shouldn't have the reversing problem anymore?
Is this something I could attempt myself... looks almost like I'd have to move the exhaust to drop the tranny...
2003 Excursion 4wd. Noticed a few days ago that when selecting reverse, it seemed to take longer to actually go into gear. Didn't think much of it and it has been fine since. Pulled the camper a few hours away for the weekend..
Now the truck is slow to engage reverse. Even when warm, when I put it in Reverse, it takes up to 30 seconds or so for it to 'catch'. I checked fluid and it's ok. Shifter feels ok. Fwd gears are fine?
I have the backup sensor system, and occasionally turn it off with the dash switch when backing up a boat trailer. Never had to manually turn it back ON, because it is supposed to default to the ON position during startup.
Twice this week, after starting the vehicle, the OFF light stayed on the next day, and the system did not default to the ON position. (nearly backed the truck through the garage wall cause the damned thing didnt beep when it was supposed to!)
Works fine today, so problem seems intermittent...
I have a 2002 f350 that I have changed relays, control unit, checked fuses with no change. The hazards work normally. I'm ready to drive it off a cliff. I was told that it could be a bad ground. But no one can tell me where the ground may be. I have looked at the wire run from back to front with no problems found.
View 1 RepliesLast night I backed my truck up to allow another family member to leave, and the back-up sensor alarm started beeping, like it does when the tail-gate is down and backing up.
The truck had not been driven on Christmas day, but it had rained and snowed lightly (dusting), then the temp dropped to 20 degrees.
Can a light dusting/ice cause the sensor to react the same as a close object. I think it does, just trying to confirm.
How do I disable the backup alarm on the Generation II Prius?
View 2 RepliesHow to turn off the constant annoying back-up alarm in a Prius v (lowercase v for the Prius v wagon) three? I asked the dealer and they told me it cannot be done...no codes yet. I remember doing a series of settings in a Gen II Prius that would turn off the backup alarm and seatbelt chime.
View 19 RepliesMy wifes 04 Aviator gives a check backup assist when in reverse. Checked fuse no problem.
View 2 RepliesI have a 2013 F350 Lariat. Recently, the backup camera has stopped working about 1/3rd of the time. When it doesn't work, a yellow triangle icon appears on the screen with " Camera unavailable. See dealer." The dealer has checked it, twice, and is unable to locate the problem.
View 13 RepliesIs it possible to turn off the backup sensors on my X ?
When I am towing these things drive me nuts!
1999 E-350 Super Duty (figured the problem would be the same for van/truck)
Problem: Backup lights don't turn on when in reverse.
Diagnosis: Changed the fused (because it was bad) but didn't fix it. The bulbs are both good. Brake lights, turn signals all work. I understand the backup lights are connected to the Neutral Sensor Switch. To test to see if the NSS was working, I put the van in Reverse and cranked... Van didn't crank (and likewise for D, 1-3).
So I guess the Neutral Sensor Switch works. The fuse works. The bulbs are good. Haynes doesn't have much as far as troubleshooting for this issue. What should I look at from here?
I can't find any info about this "always on" reverse light issue. My searches show that most people with the problem only have it when they put it in to revers. Mine's broken but the light is on all of the time indicating it's not working.
I can go through the sensors, but I think the system only recognizes sensor failures when the car is in reverse. What's my first/next step?
I'm having an issue with my backup sensors when its cold (40 and below). The issue is, they don't work. When I put it in reverse the sensor light on the dash comes on signifying they're off. I push the button to try to turn them back on and it stays on with no change. Once the outside temp heats up they start operating as normal. How to fix this?
View 10 RepliesMy backup assist only works when it is raining!! I have read all the posts I could find on the back up system, but have not found one one my issue. I had my wife turn the key on, engine off and put the truck in reverse. I put my ear to each sensor and they are clicking. So I am assuming they are working right. I took the speaker out and cleaned it and put it back in. No beeping at all!!
It was raining really bad one day last week and as I was sitting at the curb in reverse waiting to back into the driveway a car passed me and the system started going off. It startled me and the kids. I backed in and it worked as it should. Later that night we went out to eat and it was still raining and the system worked as I backed into a spot near a light post.
The rain stopped and the truck dried out and now the back up assist is nonoperational again! What is going on? To me it seems the moisture is completing a circuit that is not being completed when dry!
Currently I have a license plate camera wired always on connected to a 7inch lilliput monitor infront of my center console on that hump in the floor. The monitor is connected to a 12v plug on the dash. In this configuration, I have to reach down and turn the monitor on whenever I want to reverse and im hoping I can make it turn on whenever I go into reverse. Right now, if I turn it on then turn the truck off, the monitor stays on with a bright blue no signal screen which forces me to turn the monitor on, then off, every time I reverse if I want to use it.
Any way to make the monitor turn on/off when I put my Ex in reverse?