I'm looking at a pair of springs from a donor truck f250/350. The number on the spring is (rpn 0612 2c34 ca). How to decode this? I know it has an overload top spring. I'm looking for a two inch lift over stock springs.
View 5 RepliesI work at a ford dealership in detroit, im looking into doing a v/b code swap, and just had some questions. my current stock excursion springs are completely shot. so i need new ones so might as well do the swap. do i need to order or get anything other than the v code springs, and the b code springs, new u-bolts, and modify the b code springs? i do not need shackles or anything to have the ex sit level when im done..? just making sure before i get involved. have viewed many topics on here about it and just want a definitive answer. 2005 excursion, v10. i actually wanted to go with the X's in front, but i dont know how to make those level in back.
View 14 RepliesA couple years ago I did the V Modded B spring swap on my Excursion. The rear was quite a bit higher than the front so I added the 3rd leaf from the old rear springs to the new front and that worked but it is still a bit higher in the rear. I regularly tow one of two different trailers 3000 lb and 5000 lb and occasionally a 20" car hauler 6000-8000 lb. The smaller ones barely squat the rear of the truck. I recently added a Plow and would like to raise the front so it is level with the rear. I need to raise the front about 1-1.5 inches. What front shackle do I need?
View 14 RepliesThe local shop here suggested getting a set of F350 springs and they would take them apart and a leaf to the front and rear springs.
View 2 RepliesI thought I had come across a chart here that showed you the different spring ratings and the expected height change difference from stock, for each engine option.
View 7 RepliesHere is my current situation. No cruise, Replaced clock spring because the air bag light was also on. Still no cruise, checked fuses, they are fine, replaced bulb in gauge cluster. Still no light coming on at all, so I can't do the self test. Do you think my steering wheel switches are bad? Is there anything else I can check?
View 14 RepliesJust had a front spring snap on my front drivers side on a road trip to the cottage. Found a place one hour away that can do new replacement front springs. The question that I have is that he can get F450 equivalent springs a lot cheaper than F350 springs. I do plan on adding an aftermarket bumper at some point in the future. What should I order?
View 14 RepliesI want some honest opinions on whether a spring swap is worth the money and time to make the ride better and less harsh of ride. I currently have a completely stock 02' 7.3 4x4 Excursion with 204,000 miles. I have been reading a lot on the spring swap and really want to know if it's worth it for the sole purpose of ride and keeping the front off the bumpstops. I don't tow enough to justify it for that reason , and could live without the lift portion because I use it for a daily and family hauler. I experience some sway but not terrible ,but I do believe my shocks are shot as well and I have hit the front bumpstops a few times over railroad tracks.
View 14 RepliesI got the new ones, (as mentioned in another thread) and they're the same as the old ones. Well, the one that's still in one piece.
I guess I'm missing something very simple, but as easy as it would be to cut the old one out...how do I make room between the lower leaf and the other leaf pack to get it out?
I about hung from the lower leaf and it didn't move quite enough to give the room to remove the bumper.
I am looking to install a new Message Center in my 2003 Excursion XLT. I have checked the vehicle for wiring and everything seems to be in the right places. I have ordered the Ambient Temp Sensor and that will just plug into the harness that is on my vehicle with a factory cap in place at the moment. However when I tried to order the message center, the dealer said it would be best to get the part number off one that is currently in a vehicle.
View 13 RepliesWhile fixing some trans leaks on my 6.8. I was tightening a clamp on the center cooler and the lines must have rotted. It snapped off. I was having problems with both attachment points. So guess it's just time. Problem is I cant find a good part number to order one. I can't find it on Rock auto. Here is a picture if it. It's between the front and main radiator.
View 10 RepliesReplaced front leaf springs to procomp, now i got a clunking noise from right leaf spring rear eye(and a little bit from the left).
Can it be that:
I've tighten them to much? Wrong way (big eye is in front)? Got about 4" lift in front and haven't received rear leveling kit yet so the angel is wrong?
Measuring the stock suspension length from bolt hole to bolt hole for me? I want to lift the front of my 05 an inch or two with longer hangers and just want to make sure the ones I have now are stock length.
View 14 RepliesWhen I bought my truck one side of my truck had plastic between the outer sheet metal and inner sheet metal and the other side was missing. It looks like the purpose is to keep mud and road gunk from shooting up into the rear area. Where I can order replacements and what they are called? I need both sides, since the one I did have was cracked and barely hanging on.
View 8 RepliesFinally pulling the trigger on some springs so I can get this work done, Tousely prices were great on the W's compared to local dealers. Here are some questions.
1. I am planning to go with the W springs up front.
2. Can I still use the B for the rear mod, or do I need C's to keep it level? (Or F's)
3. Do I need blocks in the rear, or just the springs on the axle?
4. Do I need the 2" shackle up front?
5. I have dual Fox shocks that came with the ex when I bought it. The prior owner said they ran a little rough. Are they able to be re-valved, or is it cheaper to go with Bilstein?
My leaf spring swap is almost complete... its been almost 3 weeks with all the conflicts of life but its getting near completion. Just have to do front passenger side now.. Tomorrow and it should all be done.. hopefully... Any ways... my preliminary numbers are 40" front (ground to fender) and 41.5" rear.. Might be 1/2" to 1" off since I haven't finished the job AND the truck is sitting on dirt. Any ways, What size wheel/tires can I fit on there now? And will I need a spacer with that size?
View 1 RepliesI am swapping to a 6.0 trans cooler in my 7.3 and want to add the external filter as well. I looked through the tech folder and the link about the external filter doesn't seem to be working. I am just looking for part numbers of what everyone is using. Is the Magnafine as good as a spin on style filter?
View 11 RepliesI recently installed front and rear Mag-Hytek diff covers and the front had a small leak. I thought I had gouged the housing during removal of the factory cover, so I set aside time to remove the Mag-Hytek and repair the housing. I just removed the new cover and upon inspection, there is no gouge. There is a slight scratch, but not in the area of the leak.
Upon further inspection it appears as though the o-ring wasn't properly sealing. There is a slight rust coloring where the o-ring was seated against the housing, running from where the left lower spring shackle touches the diff housing, to the bottom of the housing. The rest of the o-ring route looks clear (no rusty coloring where the o-ring was seated).
Is it possible that the spring shackle is too close to the diff, causing the new cover to not be able to seal properly? (The truck had a lift on it when I bought it. When I installed the Bilsteins, I noted that the old shocks were installed very "amateurish", so I suppose it's possible the springs were as well.)
Adding cruise control to F350 XL I just bought. I got a steering wheel with the buttons. But I am having problems with the clock spring. Mine has an 8 wire plug with only 6 pins on the big plug and all of the clock springs I have found have only a 6 wire plug for the big one. Without changing my clock spring I have no where to plug in the cruise wiring. All have been for right year model with cruise and even tried different years but none will plug in under the dash.
View 3 RepliesConversion from the dana 50 to the newer dana 60 with coil spring? My Dana 50 has called it quits so while my front end is already off the vehicle already why not make improvements. Ford used the 50 for 1999 to 2002 then upgraded to the 60, I'm guessing it was for a reason!
I've read this article on a similar project but the dana 60 had leaf springs as well: Dana 60 Conversion for F250 years 1986-1996 .: Articles I'd prefer coil spring, nothing more then personal preference with a bit of better ride quality. The donor vehicle is a 06 SRW F250 This is not what I'll be getting but just as an example of the parts I would get.
I hope i don't give the impression on my very first post that I'm a total retard......but ...I can't figure out for the life of me how to get those spring line coupling apart! I've removed the clips...but it just won't pull apart. Is there a tool to release the garter spring?
View 4 Replies