Measuring the stock suspension length from bolt hole to bolt hole for me? I want to lift the front of my 05 an inch or two with longer hangers and just want to make sure the ones I have now are stock length.
View 14 RepliesOn my 2003 Excursion 7.3L, I notticed I'm leaking what I think is coolant from the passenger side rear hard line by the front spring hanger. I haven't pealed the plastic loom away yet, but I did see the loom is chaffed near the spring hanger. What lines are the ones that carry coolant, and can I just cut the hard lines and replace with a section of rubber hose?
View 3 RepliesWhat is the correct length of the front sway bar end links. I need that info to order replacements for my 04 X EB 6.0 4x4. I just don't want to wait another day.
View 3 RepliesA couple years ago I did the V Modded B spring swap on my Excursion. The rear was quite a bit higher than the front so I added the 3rd leaf from the old rear springs to the new front and that worked but it is still a bit higher in the rear. I regularly tow one of two different trailers 3000 lb and 5000 lb and occasionally a 20" car hauler 6000-8000 lb. The smaller ones barely squat the rear of the truck. I recently added a Plow and would like to raise the front so it is level with the rear. I need to raise the front about 1-1.5 inches. What front shackle do I need?
View 14 RepliesJust had a front spring snap on my front drivers side on a road trip to the cottage. Found a place one hour away that can do new replacement front springs. The question that I have is that he can get F450 equivalent springs a lot cheaper than F350 springs. I do plan on adding an aftermarket bumper at some point in the future. What should I order?
View 14 RepliesI know 4" is still good, as that is what my 05 had. Just curious about my 00. Locally a guy is selling a pair of fab tech 5.5" front leaf springs. Just curious if I went that high if the stock drivelines would survive? We do not have a driveline shop on the island, so I would like to go as high as I can, without modding the drivelines. If 4" is all, that's fine. Just curious!
View 14 RepliesI recently installed front and rear Mag-Hytek diff covers and the front had a small leak. I thought I had gouged the housing during removal of the factory cover, so I set aside time to remove the Mag-Hytek and repair the housing. I just removed the new cover and upon inspection, there is no gouge. There is a slight scratch, but not in the area of the leak.
Upon further inspection it appears as though the o-ring wasn't properly sealing. There is a slight rust coloring where the o-ring was seated against the housing, running from where the left lower spring shackle touches the diff housing, to the bottom of the housing. The rest of the o-ring route looks clear (no rusty coloring where the o-ring was seated).
Is it possible that the spring shackle is too close to the diff, causing the new cover to not be able to seal properly? (The truck had a lift on it when I bought it. When I installed the Bilsteins, I noted that the old shocks were installed very "amateurish", so I suppose it's possible the springs were as well.)
So this may be a really dumb question, but here goes. I have a new to me 2001 v10 gas 4x4 ex. It has obviously been lifted in the past. The springs seem totally shot as the back end is quite a bit lower than the front and drops dramatically while towing. I am adding a helwig and have a wd hitch but have not set it up yet. So my question is can i do the spring swap? It would seem that i would need to address whatever changes are made from the stock ride but im not sure. I like the current lift and would be fine keeping it and adding the lift from the new springs.
View 14 RepliesI trying to find the distance/length of a 2005 4x4 onward front radius arm. I'm fitting a 2004 Cummins nv5600 and transfer case into a 1997 fzj80 Landcruiser. I'm also fitting front and rear diff/axles from a 2008 f350 however don't have the radius arms and late model f250 are extremely rare birds here as Ford don't sell them here. I want the distance from the rear bush in the radius arm(at the chassis) to the front bush (top and bottom) at the diff/axle....
View 1 RepliesI work at a ford dealership in detroit, im looking into doing a v/b code swap, and just had some questions. my current stock excursion springs are completely shot. so i need new ones so might as well do the swap. do i need to order or get anything other than the v code springs, and the b code springs, new u-bolts, and modify the b code springs? i do not need shackles or anything to have the ex sit level when im done..? just making sure before i get involved. have viewed many topics on here about it and just want a definitive answer. 2005 excursion, v10. i actually wanted to go with the X's in front, but i dont know how to make those level in back.
View 14 RepliesI'm looking at a pair of springs from a donor truck f250/350. The number on the spring is (rpn 0612 2c34 ca). How to decode this? I know it has an overload top spring. I'm looking for a two inch lift over stock springs.
View 5 RepliesThe local shop here suggested getting a set of F350 springs and they would take them apart and a leaf to the front and rear springs.
View 2 RepliesAny success story on converting 2003 or 2004 f350 with leaf spring front end to the 2005-2007 f350 coil front end is it possible?
View 8 RepliesI thought I had come across a chart here that showed you the different spring ratings and the expected height change difference from stock, for each engine option.
View 7 RepliesHere is my current situation. No cruise, Replaced clock spring because the air bag light was also on. Still no cruise, checked fuses, they are fine, replaced bulb in gauge cluster. Still no light coming on at all, so I can't do the self test. Do you think my steering wheel switches are bad? Is there anything else I can check?
View 14 RepliesI want some honest opinions on whether a spring swap is worth the money and time to make the ride better and less harsh of ride. I currently have a completely stock 02' 7.3 4x4 Excursion with 204,000 miles. I have been reading a lot on the spring swap and really want to know if it's worth it for the sole purpose of ride and keeping the front off the bumpstops. I don't tow enough to justify it for that reason , and could live without the lift portion because I use it for a daily and family hauler. I experience some sway but not terrible ,but I do believe my shocks are shot as well and I have hit the front bumpstops a few times over railroad tracks.
View 14 RepliesI got the new ones, (as mentioned in another thread) and they're the same as the old ones. Well, the one that's still in one piece.
I guess I'm missing something very simple, but as easy as it would be to cut the old one out...how do I make room between the lower leaf and the other leaf pack to get it out?
I about hung from the lower leaf and it didn't move quite enough to give the room to remove the bumper.
Replaced front leaf springs to procomp, now i got a clunking noise from right leaf spring rear eye(and a little bit from the left).
Can it be that:
I've tighten them to much? Wrong way (big eye is in front)? Got about 4" lift in front and haven't received rear leveling kit yet so the angel is wrong?
Finally pulling the trigger on some springs so I can get this work done, Tousely prices were great on the W's compared to local dealers. Here are some questions.
1. I am planning to go with the W springs up front.
2. Can I still use the B for the rear mod, or do I need C's to keep it level? (Or F's)
3. Do I need blocks in the rear, or just the springs on the axle?
4. Do I need the 2" shackle up front?
5. I have dual Fox shocks that came with the ex when I bought it. The prior owner said they ran a little rough. Are they able to be re-valved, or is it cheaper to go with Bilstein?
My leaf spring swap is almost complete... its been almost 3 weeks with all the conflicts of life but its getting near completion. Just have to do front passenger side now.. Tomorrow and it should all be done.. hopefully... Any ways... my preliminary numbers are 40" front (ground to fender) and 41.5" rear.. Might be 1/2" to 1" off since I haven't finished the job AND the truck is sitting on dirt. Any ways, What size wheel/tires can I fit on there now? And will I need a spacer with that size?
View 1 RepliesIs there any way to add Bluetooth to the stock 2000 Ex Radio?
View 1 Replies