Got a 98 explorer eddie bauer and the low beams went out. A search through the console revealed this explore doesn't have the lamp/light out module. So i guess a multifunction switch would be the next place to go? Fuses look good too btw.
View 3 Replies97 Exp xlt 6 cyl --- While driving at night w/high beams on, all lights will go completely out. Turn light switch off and back on, then they will come on again. Where to start.
View 14 RepliesThe turn signals and high beams do not work on my 1998 ford ranger xlt 4x4. I have replaced the multi function switch, the yellow flasher relay checked all fusses and all are good. What could be the problem?
View 7 RepliesI just bought a 98 F150 V6 Manual transmission 2wd truck. Its a clean truck and I'm liking it so far but its got a couple minor issues. Whats the point of buying a truck if you don't get to work on it??
The High Beams don't work at all. Low beams are fine. I've put new bulbs in, and fuse 16 in the passenger compartment has continuity. I'm suspecting the multiple function switch, because when I pull out to engage the high beams, nothing happens. The indicator on the dash doesn't come on, and the low beams don't turn off either.
The second issue is the coolant gauge doesn't read. When I turn the key to the on position, the needle on the gauge moves up just a bit, but it never moves after that. Anything to check?
There are a couple other minor things like the e-brake light on the dash doesn't always turn on, but I can deal with that.
I have a '99 Explorer XLT and when I turn the high beams on, the fog/driving lights shut off. Is this normal? Is there a way I can keep the fogs on while the highs are on?
View 1 RepliesI have a 1997 Explorer XLT. The high beam have not worked since I got it and now living in Virginia they are needed to pass inspection. When turned on (pushed forward) lights go out, high beam indicator comes on. When flash to pass (pulled back) lows stay on and indicator comes on. It does not have auto lamps.
What I have done:
Replaced MFS
Verified power from GRY/ORG wire on MFS when turning high beams on.
Verified power across fuse #33 when switch turned on.
Had bulbs tested, Good.
No power on high beam wire at the bulb socket.
The only thing I have not checked is what several people have referred to as a "splice" I think someone referred to it as S111? Where this is physically located or am I going to have to start the chore of tracing the wires?
My truck only has low beams. When you move the stalk on the colum backwords it changes nothing, when you move it forwards the low beams go out but the high beams do not come on.
View 14 RepliesI have checked fuse 46 and 47, and installed new headlight bulbs. I have high beams, but no low beams. I have searched this topic but no one has the same prob it seems. My headlight switch has broken. Could it be the headlight switch?
In my manual, it says the 2002 has a fuse panel behind the glove box. I took glove box out but it doesn't look like a fuse panel.
I recently installed new halo HID headlights in my 2003 f150 with HID bulbs and ballast the passenger side worked and the drivers side didn't nth lights wired exactly the same. I switched everything from the passenger to the drivers side still nothing I switched everything back to passenger side and they don't work now. I tired regular bulbs in the passenger side an it worked then on the drivers side and it worked for a split second and went out and then I retried t on the passenger side and it worked for a split second and went out a now neither are working. I checked all the fuses and their good. What the problem could be?
View 5 RepliesIt ford related but I just bought a used car that has hid low beams and when you turn on high beams there is no light at all. The blue light on dash comes on and head lights go off. I just got this car 2 days ago and haven't really looked into it.
View 5 RepliesMy 98 Limited started blowing hot air yesterday, even in Max AC. It even blows hot air out the defroster when the climate control is shut off. It started doing this 2 days ago, but I could still get sporadic cold air from Max AC, but now nothing. What could be the problem?
View 8 RepliesOkay here is my issue : I have explorer 98 v6 4.0L 4wd .. I changed my transfer case with the shift motor because the old one was making noise and grind .. I put a good used and tested transfer case but once i started the car to test it I noticed its feels loke stuck in 4 low ..
I parked the car and switched it to 4wd Hi. The light of 4wd hi came ON in the dash. Then I put the shifter in Neutral and moved the switched to 4wd low but the light of 4wd hi stayed ON never seen the 4 low light in the dash. I'm so confused and disappointed now. Even with the old bad transfer case it was fine other than the noise the transfer case making.
I have a 1998 Ford Explorer 4.0 V6 with 200K miles. I plugged an OBII scanner with live data readings and my o2 sensors never relayed any information (voltage), they all ead -100% and the voltage never changed. Could all four be bad? I left the truck running for 15 minutes with the scanner attached and nothing changed.
BANK 1 SENSOR 1 = -100%
BANK 1 SENSOR 2 = -100%
BANK 2 SENOR 1 = -100%
BANK 2 SENOR 2 = - 100%
I want to replace my headlight bulbs; I want to install 8000K in my low beams, and maybe 3000K in my hi beams. But all of the bulbs that I ever installed either; A the burnt out within few weeks (lost color), or B they stopped working.
Now, regular WHITE bulbs seem to work forever; but the color ones, burn out/break. Low quality?? I need a pair of very good 9006 8000K, and 9005 3000K. Again, but I don't want to change them in a week or two. I want them to last!!
P.S. 2005 Toyota Camry
I was told by the dealership that the battery was bad and needed to be replaced ( which I did) I went out to my car this morning and had the same problem. When I turn the key nothing happens. When I turn the key you hear a click but that is it.
View 3 RepliesGot a call from my little sister about two weeks ago that her Ford Explorer would not drive forward. Checked it out and put it into second to get it home.Last weekend me and my dad changed the filter and fluid and then drove it for a bit. It sounded a little better but still would go into drive or reverse. We shifted into second which we knew worked and then back into reverse immediately and now reverse worked, although sluggish. The same was true for drive. A few days later dad changed a solenoid and now it will go into drive and go up to 15mph, but will not shift from first to overdrive first. And still no reverse right away. She is able to get to school with second gear and pop into drive when she gets up to 40-45mph. If she has to backup from start, first she has to put it into second and then back to reverse. Something in overdrive doesn't seem to be doing its job right.
View 3 RepliesMy 98 explorer is hiccuping when i am stopped for more than a few seconds and when I press the gas to get going it stutters. It only does this if I am stopped at a light or stop sign for a few minutes. Once I get going again it runs fine. The check engine light is not on and I have replaced the o2 sensors and spark plugs. I am at a loss on what to do next.
View 6 RepliesMy ford just suddenly started backfiring and started smelling like this sulfer kind of smell and knew I needed a new exhaust so I got a new tailpipe and muffler and problem still persisted so then I replaced the driver side catalytic converter because I had noticed after driving it that it was smoking after driving it. So now I've replaced that and i still got the smell and it just rides rougher and the check engine light is blinking after driving a couple minutes....
View 9 RepliesI'm thinking about buying a 98 Explorer that has an ABS light on. I haven't looked at it yet. In the ad, the seller claims it's due to worn brake pads in the rear. If that's true, then it's not a big deal. Can the ABS light be set by worn pads? Most of my cars are too old to detect this, but even if they did, I wouldn't know because I never let my pads get that low.
View 7 RepliesHave 1998 Explorer with 5R55E tranny and the automatic transmission extension housing seal keeps coming off, allowing a fluid leak. I just replaced it and it's doing it again. When I put it in there, it seemed tight, but... How to keep this thing in there?
View 3 RepliesMy explorer 98 seat lumbar does not work. When i push the switch i only hear a motor noise and nothing happens. How to fix that?
View 6 Replies