Ford - Explorer :: 1998 V6 Stuck In 4 Low
Apr 13, 2015
Okay here is my issue : I have explorer 98 v6 4.0L 4wd .. I changed my transfer case with the shift motor because the old one was making noise and grind .. I put a good used and tested transfer case but once i started the car to test it I noticed its feels loke stuck in 4 low ..
I parked the car and switched it to 4wd Hi. The light of 4wd hi came ON in the dash. Then I put the shifter in Neutral and moved the switched to 4wd low but the light of 4wd hi stayed ON never seen the 4 low light in the dash. I'm so confused and disappointed now. Even with the old bad transfer case it was fine other than the noise the transfer case making.
View 1 Replies
Advertisement
I have noticed when I turn the key on the needle moves down just a touch but goes back to full. I have disconnected the wiring harness for the fuel tank and reconnected it. I have tried tracing the harness back towards the front but no luck yet. I'm guessing it's a bad ground or something. And if so what was the solution.
View 5 Replies
My 1994 Explorer is stuck in 4 low. None of the lights are on in the dash or at the switch. I got the switch out & with a test light running I have weak power at the top left terminal better power at the 2nd, 3rd &4th on the right. No power on the opposite terminals. Is my switch bad or do I have a different problem. Also how do you remove the switch from the dash vent ?
View 1 Replies
After using the 4wd it's not going back into 2wd,the 4wd lo light is on and I dont hear the "click" when turning the switch. I've had the truck several years so I know how the 4wd works,is there a fuse or something else to try?
View 4 Replies
Have a 97 Explorer 4x4. lately when I start the truck it has shifted itself into 4x4 low. I had disconnected the battery for a few minutes, re-connected and the truck was back in auto. This no longer works and it is stuck in 4x4 low. Mechanic wants to replace transfer case encoder, but says more diag needed after to replacing encoder motor to determine internal failure and may need more work. Can I simply have the 4x4 low disengaged manually?
View 3 Replies
Need to find vacuum hoses, a/c is stuck on defrost.
View 1 Replies
My explorer is stuck in 4wd and no 4wd light is on. How can I get it out. Coz its hard to drive?
View 14 Replies
Got a 98 explorer eddie bauer and the low beams went out. A search through the console revealed this explore doesn't have the lamp/light out module. So i guess a multifunction switch would be the next place to go? Fuses look good too btw.
View 3 Replies
My 98 Limited started blowing hot air yesterday, even in Max AC. It even blows hot air out the defroster when the climate control is shut off. It started doing this 2 days ago, but I could still get sporadic cold air from Max AC, but now nothing. What could be the problem?
View 8 Replies
Well I was trying out my four wheel drive today and it worked fine until I went to turn off switch, it would not cut off it is a 98 F150 switch is located on dash. It is stuck in four wheel high!
View 3 Replies
I have just put in another transmission and the truck will not shift out of first gear, it will go in reverse and first and reverse. The guy who had it before me had the same problem when he put in a transmission with only about 40-60,000 miles he assumed it was a bad transmission. And that's how I ended up with the truck. We have so far installed yet another transmission and it is doing the same not shifting out of first that it did for him. There is no cel or blinking overdrive lights, checked fluid levels, checked selinoids, gonna purchase a used computer for diagnostics, I am stumped with limited knowledge. The dealership said the transmission should be the e40d I'm reading it should have the 4r100 is that correct? The truck is the 5.4L v8 with 74,000 original miles. Truck sounds amazing. I really want to fix it.
View 2 Replies
I have an '92 Explorer 4X4 with a stuck emergency brake. I have tried tugging on the lines from the back of the truck (where the line splits into two beside the frame). The brake is stuck in the on position, and when I pull the release nothing happens. It has been cold here lately, so i thought they were frozen, but after pulling the release lever, it seems like a mechanical issue.
Any temporary solution that get my truck drive-able and to my mechanic for a closer look. I am not very mechanically inclined but it seems to me that the release lever is pulling at nothing and not moving the cog to release the actual emergency brake.
View 1 Replies
A friend of mine at work has a 93 4wd explorer. A4ld transmission. Reverse quit working, and no matter what gear you put it in, reverse, neutral, or park, it will stay in drive. Park holds itself, but if you give it gas, it tries to pull. He says when it's in reverse, it's almost like it's stuck in reverse and forward, it wants to rock. He pulled the pan, no metal shavings, and pulled the valve body. He said the screws holding the valve body were finger tight. The gasket underneath had a small tear in it, he doesn't know if he did this pulling it out or not. He replaced those gaskets and retorqued the valve body. When he put it in reverse and topped off fluid, reverse worked. He put it in drive and it worked, but when he put it back in reverse, it stayed in drive and is staying in drive in all gear selections again. He bought this explorer new, and the transmission had never been into before.
View 3 Replies
'98 XLT 4.0 SOHC.
First of all overdrive started to play up, the engine would flare as it went into OD and often would have several goes at it until it engaged OD. Finally it wouldn't go into OD.
Still driving it around for awhile then it went into limp home mode - stuck in 3rd gear. What it might be?
View 12 Replies
I have a 1998 Ford Explorer 4.0 V6 with 200K miles. I plugged an OBII scanner with live data readings and my o2 sensors never relayed any information (voltage), they all ead -100% and the voltage never changed. Could all four be bad? I left the truck running for 15 minutes with the scanner attached and nothing changed.
BANK 1 SENSOR 1 = -100%
BANK 1 SENSOR 2 = -100%
BANK 2 SENOR 1 = -100%
BANK 2 SENOR 2 = - 100%
View 3 Replies
98 F150 4.6L 4WD...
Attempted to replace fuel filter tonight. The connector on the fuel tank side of the filter came off just like it is supposed to. The engine side, however, will not come lose at all. I can wiggle to back and forth, but I can't seem to get the tool to compress the springs.
The engine side connector seems to be smaller than the tank side. I've done this once before on a '98 Ranger, but didn't notice a difference in connectors.
View 9 Replies
I was pulling into my driveway. I put the car in park, but when i went to get out of the car, it started to roll forward. When I finally got it stopped, I tried to shift it, and it wouldn't shift to any spot. Then it became stuck in between Park and Reverse. I can't move the gear shift.
View 1 Replies
I just picked up another 2003 XLT and I'll be taking it in for inspection on Monday. Hoping it will pass easily, but there are a couple issues I'd like to address before going in there.
First and foremost, the heat/AC system is stuck in defrost. It will turn off when the selector is moved to the OFF position, but any other position just makes the air blow out the top of the dash. I did do some research on this beforehand (the seller made me aware of it) and I first looked at the actuator. When moving between positions, the actuator does not move at all. It does appear to be connected to the vent door's arm but there's no movement when going around the dial. I do hear what seems to be a relay kick on or off as I go through the different modes, but that's it. Does this point more towards a vacuum issue?
Second, and less significant...the self-dimming rear view mirror doesn't dim. It doesn't even power on. Where might the connection go for that mirror? Would be handy to have for night driving, but not that big of a deal if it's not functioning.
I'm also going to have to get the tailpipe mounted...seems it came off at some point and the seller asked me today if I wanted it. Uh...yeah, I'm gonna need that to pass inspection!
I am liking it so far. Runs well, rides well...I will be enjoying this one as well.
View 9 Replies
I had been waiting to fix my explorer for a long time. The "previous owner" I will call him knowingly sold me a vehicle with a bad tranny without disclosing it... long story. To get to the important part, it had the common 2/3 shift flare. I dropped the pan, filter, and valve body, making sure to use a template and put the bolts where they go. Then i took the valve body to the work bench and replaced the gasket, which was surprisingly not blown. After more looking around, I realized the previous owner had already had the fix done. I tightened the EPC 1/4 turn and reassembled the tranny. When i started it, it was stuck in first gear. PRN21 all went forward (park just revved a bit due to the park lockout.)
I tore it back apart and found that the plunger on the side of the valve body was stuck in the 1st gear position. I pushed it back out and cleaned it up so it moved freely. Then I reassembled the tranny using new fluid again.
After that the tranny was stuck in neutral. I dropped the pan again today, and tightened the valve body bolts and made sure my solenoids are tight. Filled it back up slowly with the engine running. It shifted into gear for a second (tried to go forward while it was in reverse though). Then it was again stuck in neutral in all the gears again.
View 2 Replies
Last night while driving, my transmission made a pretty severe clunk, but then appeared to act normal. However, a check engine light came on so I pulled over immediately as I was literally at the entrance to a gas station.
I looked under the vehicle, under the hood, saw nothing leaking, nothing obviously broken etc. So got back in and started the engine, went to shift into reverse and the transmission clunks, same going from N into D.
I limped it home, but while driving noticed that it was not shifting but stuck in one gear.
This morning I scanned for codes and the only one showing is P0770 Shift Solenoid. I searched this forum though and get 0 results on that code, searching Google is also surprisingly vague. I believe (could be wrong though) that I have the 6R60 Transmission, it is a 2008 Explorer with the 4.6L V8.
Where to check first? When I get time I am going to check the fluid level, but could not last night as there is no dipstick!
View 3 Replies
Was replacing the struts and front ball joints on my wife's '04 Explorer last week. I get to the last one (driver's side front) and the lower strut bolt seems to be frozen to the bushing. I heated it up and beat on it a little bit. Nothing. Just wondering for some other way or am I going to have to cut it out?
View 3 Replies
