1999 Explorer XLT V6 SOHC.. I noticed today that my brakes drop nearly to the floor when I press on them. The car just passed inspection so I doubt that they brakes are worn. Master Cylinder has the correct level of fluid and the pedal is hard when the vehicle is off, so I doubt that the master cylinder is failing. How would I go about troubleshooting this problem?
View 4 RepliesRecently my F350 has failed to downshift when the accelerator pedal is pressed to the floor to speed up in traffic. It will usually happen when traveling at speeds in the 30's-40's. It will shift quickly at slower speeds. I have a scan guage on it all the time and it is not throwing any codes.
The transmission has only been serviced by the dealer; last done about 24000 miles ago. No leaks or low fluids/no burned smells. Stock setup with no heavy towing use. Currently at 228000+ miles, this is the first issue with the transmission assuming I am looking at the right area for the cause.
2005 F350 XLT 4WD
I believe my brakes have a problem.
Lately, I can stomp on my brakes @ 50 mph and they won't trigger the abs or come close to skidding the tires. The peddle goes to the floor if I push hard enough and the truck doesn't seem to stop fast like it used to.
I'm wondering if there is an issue I should be focusing on, like swelling brake lines or some issue you may know of. I'll try bleeding the brakes this coming weekend, but i think its going to be a bad brake line or something.
Our '99 Explorer leaks when it rains. The water drips from under the dash on the driver's side floor. A while back a dealership put all sorts of sealant around the windshield gasket and that seemed to work for a while.
Where are the drains for the door channels, windshield and the air intake where the windshield wipers are connected? I'd like to make sure they are clear.
The problem occurs when you hit bumps while braking, or if you get on the brakes to hard. It seems like the brakes lose pressure entirely and the pedal goes to the floor. It kicks back in when the ground smooths out, or if you are braking hard it slowly grabs again. At first i thought it was sliding, but it definitely is not. The truck appeared to be equipped with abs but the previous owner seems to have cut the abs wire/sensor at the hub. Another thought i had is maybe the brakes need to be bled and have fresh fluid put in them, I have not tried this yet (Plan to this weekend along with a dozen other things). Its rather scary when it happens. but i didnt think much of it until i nearly rear ended someone..with my younger brother in the car. Now i need to fix this asap.
View 14 RepliesBrake issues 2003 f250 super duty 6.0. Changed master cylinder, drivers side rear brake hose, new pads all around. Pedal is good at times for a few seconds. I've bled them all numerous times truck running or not flushed power steering pump new fluid. Brakes are spongy or go to floor. Do I need a scanner?
View 2 RepliesWhen I press the pedal down the pedal vibrates and make an odd sound like errrrrrrrrrrrr best way I can explain it...
View 5 RepliesDetails about my car: '91 Nissan Maxima. His name is Max. 183,265ish miles on it. Transmission was replaced maybe 8 years ago(?) My dad said the oil was changed at the 500 mark. Filled the tank up at Citgo with regular gas on Friday and only drove about 50 miles (I fill up every 200 miles or less). Max turns on but you have to floor it just to move an inch and it smells like gas.
View 15 RepliesAfter my local brake shop changed the front rotors and brake pads on my 99 grand cherokee the brake pedal is spongy and long, almost reaching the floor. They don't know why. Apparently they had a problem with fitting the new pads. I took it to the jeep dealer and they told me the master brake cylinder was leaking and needed to be replaced. many hundreds of dollars later the brakes are still spongy and long and does not correct with repeated pumping. The dealer was also stumped and I complained that nothing changed with the new master cylinder. what might be the problem?
View 4 RepliesI have a 2003 Toyota Rav 4 Sport with 160,000 miles. I take good care of it, as it does me. All of a sudden, while driving on CA freeway, it seemed to slip out of gear into neutral--no power when accelerator pressed to the floor. The power came back quickly, but this happened again the next day, with no apparent cause. I took it to my mechanic and, as I drove the surface streets, there was a knocking sound.
My mechanic said the initial problem was a transmission issue and referred me to another mechanic. And, he said the knocking may be a thrown rod(?). The second mechanic confirmed the first guy's transmission assessment (he's a transmission specialist, so of course, he'd see a transmission issue) and said he'd need to fix that before addressing the knocking. And, he said to fix the transmission (including replacing the computer that drives the tranny).
02 Montana with 4T65E electronic 4 speed transmission. car has 75000 miles. normal driving and shifting seems to be fine. Transaxle will not downshift with accelerator pedal pressed to the floor. no check or service engine lights.
View 1 RepliesFord Explorer has been making horrible noise (constant whine when accelerator is pressed)... The mechanic said he found metal in the power steering fluid and told me we need to replace the power steering pump and the rack & pinion system. Is he right about this? He said you can't replace one without the other... I've done a little research and I think we can get away with a new pump.
View 2 RepliesI have an '03 Ford Explorer (V8) and recently had a rebuilt engine installed (at 135,000 miles). As soon as I got the car back, the engine whined and it's getting louder. The whine starts immediately but it louder when the accelerator is pressed. The sound reminds me of a car with bad power steering, but it's so much louder and doesn't correlate to turning the wheel, but pressing the gas pedal.
View 6 RepliesFord Explorer has been making horrible noise (constant whine when accelerator is pressed)... The mechanic said he found metal in the power steering fluid and told me we need to replace the power steering pump and the rack & pinion system. Is he right about this? He said you can't replace one without the other... I've done a little research and I think we can get away with a new pump.
View 4 RepliesMy 2013 Lariat has just over 7,000 miles on it now. If you brake lightly at 55-60 you get a brake shutter, enough to feel it in the seat but also can see the steering wheel shake too. if you brake a little harder you don't feel the shudder much. is it possible to warp rotors in 7000 miles? 3500 of that 7000 was put on driving to Texas and back.
View 14 RepliesOk, did an intake manifold cleaning on my 99 Accord the other day, and now I have problems...
Long story short, some time ago my car started to have a very rough idle. Took me awhile to find the problem. Turned out the air hose, between the filter and throttle body, had developed a big hole on the underside. So I replaced it and while I was at it used some throttle body cleaner, spraying into the intake manifold chamber. Lot of junk blew out the tailpipe. The car ran much better, but the idle could still be a little rough. I ran it that way for awhile, and finally the other day decided there was probably still some junk in there and it was time to really clean it out. So I took ff the throttle body and intake manifold housing. There was a lot of junk in there! The small intake on the passenger side was completely clogged shut. (I understand this isn't surprising on these cars.) I used a bunch of rags and 2 cans of Valvoline throttle body cleaner and a lot of elbow grease and cleaned it out. I was thinking to myself that whatever I didn't get with the rags flushed through OK, but I didn't want to take the whole intake manifold out.
So I put it all back together. (I took a video before I started, so I'm pretty sure it's all back together right.) But now I have problems. The car starts. It idles fine mostly, but can be a bit rough. But the trouble starts when I put the pedal down. If I do it in Park, well, if I push it quick the engine just dies. If I push it slow, the engine revs then quits, revs and quits, over and over. Similar if it's in gear. If I push it hard, the engine stalls. If I push it gentle, it revs up, but chugs along a bit.
I've run some seafoam through it, thinking it was clogged up with all that junk, and sure enough, lots of smoke comes out, but nothing is improving so far. What have I done wrong?
I bought a 2001 chevy malibu about a month and a half ago.when I test drove it,didnt notice any problems or leaks...after driving it for a 2 weeks...the brake pedal would drop to the floor while driving and then if I hit it again real quick it would be ok...this problem would happen now and then....we replaced the right front caliper thinking that it was sticking and bled all the brakes..There was air in the system..everything was fine for about two more weeks then while driving the pedal would get hard when applied and then drop again..not all the way to the floor,and it alternates that way..what are your thoughts? I don't have much money to fix this problem.
View 14 RepliesI own a 2001 Ford Explorer and have had the regular wear and tear but this problem has me stumped. A few months back I had to change the auto body gasket because the truck would not go into gear. After doing this the truck ran fine, I also changed the tranny fuild and filter. The other day i went to back up into the garage and the truck stalled and died out. it started right back up and it runs fine in all other gears. (P,N, D, 1,2, 4x4 high and low) and the over drive is working fine. when the truck is cool and hasn't ran in a while i can start it and the rpms stay at about 1000 th 1200 and the reverse works great. Now when the eng. heats up to normal and i put in in reverse the rpms drop to about 4 to 500 and it stalls out and dies. I have cleaned the mass air flow sensor, the throttle body, and the IAC valve but still dying out. Im thinking it may be a vaccume leak or the IAC is bad and cleaning just wont do the trick. I have also read that it may be the back up light wiring that hooks to the tranny may be shorted out.
View 4 RepliesI'm hearing a squeking noise when I go over bumps and when I i press the brakes. sounds like it could be my springs or some such related thing.. Could it be a different front end issue?
View 1 RepliesI have Toyota Prius 2006 with about 58k miles. For the last 12-16 months I encounter the following problem: when I press brakes, I hear knocking noise. It doesn't happen every time, but when it does it only happens when I press the brakes. Once I brought my car to a Toyota dealer and waited for an hour until my car was taken for a service. Mechanic found no noise. I tried to produce this noise but my car didn't want to cooperate. I don't see any messages on a display screen. It happens with power on/off and pressed brakes. What the knock is and how to get rid of it?
View 2 Replies2000 Explorer 4.0 dohc avd. 150k miles. The torque converter lock-up function has started to drop out. It can happen after some miles and will light a warning light in the dash that the manual states as "contact tech" or something like that. Everything gets back to normal with just a "blip" to "off-position for the ignition switch and might stay normal for all between 5 minutes to several hours. Seems to me it is an electrical issue. Dirt, sensors?
Runs and shifts fine other than this. Only thing I have noticed is that the temp gauge reads pretty low but I think this started earlier and I understand that the temp gauge has its own sensor. Where to start looking?