Ford - Explorer :: 2000 XLS - Engine Hesitation - Constant Hiccup
Sep 10, 2013
I purchased my first Ford back in 2006 it was a 1999 Explorer Sport. Gave me a long line of problems from suspension to head gasket repair to rear main seal repair to ANOTHER head gasket repair. But sure enough, like I'm sure many of you have, I fell in love with her. She could do no wrong. Even now that I got her off the road she is still my baby. Now my recently purchased 2000 Explorer XLS which I've only had for about 5 months just yesterday started doing a strange hesitation. Perhaps a misfire. My initial instinct was dirty fuel injectors that hopefully if I'm lucky will be the easiest fix in Ford history. Another hypothesis is a bad plug. Either way, in my mind, that's best case scenario. I have yet to take it in and plan on buying some injector cleaner later on today. When I'm idling there's no problem. It's as soon I step on the gas that I feel the hesitation. Almost like a constant hiccup.
View 6 Replies
Advertisement
I have a 98 ford Explorer that has some serious trans problems. It all started a while back when I was pulling a small 10 foot trailer and when I go to where I was going the trans puked out what looked like all of its internal fluids. It was a hot day, and these problems seem to be exacerbated by the heat but who knows. Yes the check engine light is on. I also have the occasional O/D OFF light blinking at me. As of late the vehicle has started to act like it has a stall converter on it. I have to rev to nearly 3k RPM before it will engage.
I changed the fluid and filter about 2 months ago and the fluid is already grey and nasty. The vehicle has also started going FORWARD in ALL gears, Reverse, Neutral, etc. all are forward gears now. The trans occasionally overheats and pukes out a large amount of fluid but I cannot tell where it is coming from. At road speed (55 MPH) the engine surges when it is at a constant 2500 RPM. I know my outlook is grim but if I just need a new torque converter I would like to know before I go the the Salvage yard for a different transmission. BTW. The engine WAS replaced around 12,000 miles ago with a donor engine from a flipped vehicle.
View 4 Replies
I have a 1997 explorer sport 4x4 4.0 sohc It has a real tuff time with cold starts sputters won't hold and idle sits at about 500 rpm once its warm its not as bad still has a low idle.
Also i have a constant engine rattle thinking left front cam tension-er
Also throwing and check engine light odb scan tool shows o2 sensor position two is bad
I was thinking intake gaskets and new tension-er is a good place to start.
View 1 Replies
I have a real problem with 2000 Ranger, after changing the upper radiator hose and thermostat, I now have a pretty constant leak from the gasket between the thermostat body and engine. Appears to be something that is triggered by the thermostat opening, so whatever the leak, the thermostat is blocking it.
I've changed the gasket, cleaned the mounting surface as good as I could. Tried re-torquing the bolts, but on that score - what is the torque specs for the 2000 3.0 liter Ranger?
But ultimately, what the heck is wrong here? This should be a pretty brainless operation really. Am I tightening the connection too much and cracking the gasket? I guess that has just occurred to me, although the gasket is not as stiff as a typical fiber gasket is.
View 10 Replies
My Mother has an accent 1.3 glx on a 55 plate the problem she has is that every time she accelerates the car does a hiccup (her words not mine) the engine management light comes on and off and then its fine.
View 3 Replies
I drive a 2000 Ex V10. My truck has been having an issue at idle after it warms up, almost every time after it sits and cools down.
My problem is that once the truck warms up, it will drop down to 500 rpm's and will have a hesitation/miss/lope for about 20 seconds. When it does this I can hear the exhaust making a sputtering sound. On two occasions during windy rain it would hesitate while driving but then straighten up within a half mile or so and be fine. I have changed all the boots, cop's and plugs and don't think that is where my problem is.
What I can't figure is why it seems to hesitate/lope once it warms up! This problem not related to a failing boot, plug or cop?
View 1 Replies
I have been picking at an engine vibration for more than a year.
I have a '00 Explorer 302 V8 installed in an '82 Volvo. This engine/transmission has not been abused and only has 15k miles since it left the Ford factory. It was found intact on a pallet in dry storage. Everything was there as from Ford from the fan to the transmission output bushing. There is an engine vibration beginning about 2000 rpm in PARK so the problem is not in the transmission or drive shaft.
Perfectly smooth at idle and until you approach the start of the vibration.
Replaced the viscous clutch mechanical fan with duel electric so it isn't an out of balance fan.
Pulled the serpentine belt this afternoon and still have the vibration. Might have been a little less and I did find a idler pulley that had a little rattle but the big vibration is still there with only the harmonic balancer through torque converter rotating.
Replaced the pulley. Nothing else changed from when Ford built it.
No OBD codes.
View 6 Replies
Had this truck a few years now, and it has always had a slight miss/hesitation and maybe a few codes. The timing chain skipped a tooth and the truck was down for about a year. I have 4 other trucks, so it wasn't a big deal. I finally had time to put a new oil pump, chains, guides, tensioners, phasers etc. The truck actually runs very well and quiet. But, now misses far more than I remember it doing.
When driving in town constant at 25-30 mph occasionally it will loose power for a brief moment(<1 second) and then be fine, the security light on the dash turns on for a few seconds. It drives at 55-65 just fine, unless I am going up a hill or something else increasing the load.
2004 5.4 3v 2wd
CEL-
P0453 (fuel tank pressure issue)
P0351 (ignition coil a primary/secondary circuit malfunction)
P0356 (ignition coil f primary/secondary circuit malfunction)
The coil packs are new, and I have injectors on order. Also found this thing on the back of the motor, it connects to the fuel rail on the drivers side. Where it should go. I looked on my other trucks. But my other 04-4wd has a box by the battery it connects to, but mine doesn't have any of that stuff. And my 08 doesn't have anything like this at all.
And a pix of the truck in question.
View 2 Replies
I have a 2000 Jetta with the 2.0 automatic and just like the title states, I have recently developed a engine vibration that is felt at all times. It is much worse when the car is in gear. I only seem to feel it in the gas and brake pedals. It does not seem to depend on speed nor does it only occur at certain rpms. It feels like someone zip tied a vibrating back messager to my pedals. I want to find out what it is because on long commutes my foot begins to feel like its falling asleep. I can visually see the engine vibrating with the car in gear. I am leaning towards motor mounts.
View 1 Replies
My 2001 1.5l works fine when cold however once it reaches temperature it will hiccup and then stall! It WILL NOT fire up until it gets cold again. Usually happens when we are coasting to a stop. I'm not a mechanic but can am mechanically inclined. I brought it to Autozone and had the computer codes sent (yes check engine lt was on) One code was a fuel lean code. Cannot recall the exact number. When it act up it sounds like there is either no fuel or no fire. I cleaned the mass air sensor and put fuel treatment in it and I replaced the fuel gas cap.
View 1 Replies
2000 Hyundai Accent GS, 1.5l, 4cyl SOHC...
I have a slight issue. A few weeks ago, I put some "STP" style fuel injector cleaner into my gas tank. Either A) It cleaned everything really well and clogged my injectors, or it turned into gunk and possibly clogged something else up.
Ever since that day, my issue is that the car "stutters" very slightly. When idling, it'll "hiccup." When I'm doing normal driving, 55-60mph at 2k RPM, It'll almost feel like a transmission slip.
I've went and replaced my Fuel pump, filter, and now I've done half a can of seafoam through the brake line power booster (vaccuum) straight into the engine, and the other half into my oil for further cleaning. I also applied Seafoam Deep Creep into my throttle body, just for further maintenance.
Ever since then, everything has been running noticeably better, and I've had a huge increase in gas mileage, but there's still a slight hiccup that occurs during idle and driving.
I change the oil /filter, plugs, wires, air filter on a regular basis.
I also had to change the MAF at one point in time, as it died and the car wouldn't start at all.
Next thing I'm thinking about doing is changing the plugs / wires one more time (it's been about 5 months since my last change) just to see if I bought a faulty plug.
The car was put on a computer and the only error code that came up was one about my check engine light being out.
View 3 Replies
My 04 hyundai accent about 2-3 months ago acquired a hissing noise which seems to be coming from the middle of the engine compartment. The car only has 100,000 miles on it.
It is a constant hiss that only stops when the gas pedal is pushed initially. I have looked all over the car and can not see any fluids leaking at all. It is pretty loud and can be heard easily outside the car when the car is on.
I hooked up my obd2 reader and found these codes:
P0304-Cylinder 4 misfire (I notice it when the car sits at idle for about a minute)
2x P0121- Throttle Position circuit range/performance problem
2x- Evaporative emission incorrect purge flow.
View 1 Replies
my 2006 GX has 95000 miles and recently i've noticed a slight hesitation followed by a slight surge in speed while driving at a constant speed. it almost feels like i'm pushing the accelerator then releasing it. its a very mild difference but i'm guessing tranny and have 5k left on my warranty. it occurs at a variety of different speeds but most noticeable at about 35-40mph and up around 55mph.
View 6 Replies
Ford Explorer has been making horrible noise (constant whine when accelerator is pressed)... The mechanic said he found metal in the power steering fluid and told me we need to replace the power steering pump and the rack & pinion system. Is he right about this? He said you can't replace one without the other... I've done a little research and I think we can get away with a new pump.
View 2 Replies
I have a 2000 Excursion with the 7.3L. We bought it in February of last year with 81,000 miles on it, and it has 111,000 miles on it now.
First problem:
It threw a code today: P0683 indicating a communication issue between the Glow Plug Control Module and PCM Communication Circuit. Other than the code, the truck isn't doing anything out of the ordinary today. Drove it about 40 miles, up to 80 MPH, problem three below did show it's head once, but other than that it ran great.
Second problem:
Ever since we've owned the vehicle it has done a strange surging/near-stalling thing (for lack of a better word) when it's started up. It only does it occasionally, and the problem seems to appear, and then go away for several weeks or months only to reappear. Here's how it goes:
- Start truck
- After starting the truck immediately begins to surge (rev?) and then nearly stall.
- It will do this over and over, about one surge/near-stall cycle per second, until I tap the accelerator, at which point it stops immediately. So far it has never stopped on it's own, but has always stopped with a tap of the accelerator.
Up until recently I chalked this up to "huh, that's weird" since the truck has otherwise run fine.
Third Problem:
Every once in a while the truck will hiccup while it's up to speed. It only seems to do it at highway speeds, typically between 55-70, and the hiccup typically only occurs once.
The first time I distinctly remember it happening was right after I had replaced the Camshaft Position Sensor (approximately 5-6 weeks ago).
While digging around online I found one other guy say his truck started doing the same thing after replacing the CMP in his F250 with the same little plastic gray one I used. So that problem might be caused by that part.
My Thoughts:
It seems like the run-away favorite for fixing problem one is to replace the GPCM. I've dug through a couple hours of forums this afternoon/evening, and it looks to me like the GPCM is the culprit the vast majority of the time when code P0683 comes up.
I'm thinking problem 2 might be an ICP issue. I can't find any previous forums anywhere that describe the exact issue I'm having - or really anything very close. Maybe it's out there, but I couldn't find it. So I'm really grasping at straws.
Problem 3 could either be related to the ICP (if problem 2 is an ICP problem) or it could be due to the new CMP I installed (the cheap gray plastic one from Autozone). It's possible the hiccup has been around longer than I think. Half the time when it happens (or does it?) I can't decide if it was a hiccup or a bump on the road I didn't see. I am sure it's happening at times, but there are other times I'm not sure if it was a hiccup or a bump I just didn't see. So I think it's possible it's been going on longer than I realize, and I noticed it that first time because I had JUST been under the hood and pretty finely attuned to how the truck was running as a result.
I'm about to hitch my 35' camper to this truck and haul it a few hours and I'm not feeling real confident right now. Problem 1 hit today, problem 2 is more prevalent than every right now, and problem 3 has been hiccupping for 5 or 6 weeks. I'd like to get at least problems 1 and 3 sorted out before hauling 8,000 lbs if possible.
View 8 Replies
Ford Explorer has been making horrible noise (constant whine when accelerator is pressed)... The mechanic said he found metal in the power steering fluid and told me we need to replace the power steering pump and the rack & pinion system. Is he right about this? He said you can't replace one without the other... I've done a little research and I think we can get away with a new pump.
View 4 Replies
I have passat 2007 2.0T , about 98000km. A few months ago, my vehicle randomly has hiccup with EPC light when I put on the pedal. Each times i put on the pedal my vehicle hiccups and EPC light on and all goes away when i put off my foot from the pedal. It happened randomly, so i went to vw dealership twice. They keep saying they could not find any problem. Coz as i said it happens randomly. I paid diagnostic fee but still the problem remains.
Unfortunately today i had the same issue hiccup like crazy with epc and engine lights. Also on the highway my baby 2 years old was with me when i drove, my vehicle lost power all the sudden, all most i involved an accident with following vehicle. I started the engine, vehicle moves but with the problem. I feel wheels do not spin properly or transmission randomly. What the problem is?
View 1 Replies
The other day I went to turn off my vehicle and it continued running even when key is in off position. I took the key out and it still continued running. I had to disconnect the battery and turn key in on position for vehicle to stall. I do not want to buy any unnecessary parts nor do I want to take apart any unnecessary components.
View 1 Replies
Its getting worse. Noticed it a month or so ago, very slight ticking noise when the engine was cold. It would go away after a minute or two when the engine warmed up. Kinda sounded like a lifter ticking type noise when low on oil but I was not low on oil.
Now its getting more noticeable and it doesn't go away. Very noticeable when I take off or accelerate. less noticeable when I take my foot off the gas but its still there.
What it might be? I am pretty newbie about engines and I don't want some repair outfit telling me I need a rebuilt engine if all I need is to tighten my manifold or something. Because that would be my luck.
2000, XLT, 5 Liter V8, 178K miles.
View 5 Replies
The other day I went to turn off my vehicle and it continued running even when key is in off position. I took the key out and it still continued running. I had to disconnect the battery and turn key in on position for vehicle to stall. I do not want to buy any unnecessary parts nor do I want to take apart any unnecessary.
View 3 Replies
My V6 3.0 TDI 2007 car is basically just driving fine, however occasionally i did noticed (when cold) a rare hiccup in accelerator response from standstill. Today i made a scan on VCDS, and found this engine fault, what could it be? The car is officially and recently maintained by VW dealer.
View 11 Replies
