I have a 1999 F150 Supercab, 2wd. I just replaced the front rotors, calipers, and pads. Before I did this, the front right caliper was locking up completely. Now, after the new stuff is installed, the truck pulls very hard to the left when braking. The harder you brake, the harder it pulls left. What should I look at next?
View 2 RepliesMy buddy has been having a strange problem with his 275,000 mile 2003 F150 2wd. The right side caliper will lock up out of the blue and will not release for anything. We put 3 news calipers on it within a 4 week period thinking that we had a defective one but no change. I am thinking either a bad brake line or, more likely, the front abs block...
View 1 RepliesBought a high mileage 99 f150 4x4 yesterday. In the process of cleaning her up, the water hose hit the disc brakes on the drivers side and it was hotter than a BBQ grill! Ok, immediately I thought this isn't good. Jacked her up and pulled the caliper. Pads were almost gone so replaced them with a new set, went for a drive. Now the damn things were smoking so bad I thought they were gonna catch fire! Sticky caliper , right? Stopped and got one then realized that the passenger side started doing it too.
Another trip for the other caliper and new pads because these were toast. I mean just burnt to hell. Before I started working on the truck again, I checked on here and I'll be darned if I didn't find out that the old brake hoses might be acting like a check valve because of rust and deterioration. Got a set of brakes hoses too. Put everything on this morning and works like a charm.
1999 4.6 XL
Passenger side done
I have a 2000 f250 4x4 with 4 wheel abs. The front passenger side caliper keeps locking up while I'm driving and won't release and when I hit the brakes it pulls hard to the drivers side. I have put two calipers on the passengers side and put new brake lines on.
View 8 RepliesI have a 2001 f150 4x4 with the 4.6 Triton motor, the front axle is not pulling in when I switch the selector on the dash, I know the transfer case is switching so that part is ok. I know there are 2 solenoids on the fire wall, my question is which one is which ? every store I call says one has the nub at 9 o' clock and one at 6 o' clock which one of these does the front axle, don't want to order the wrong one ? I checked the vacuum and the blue line going to the axle always has vacuum and as I read the diagram the blue line is 2 wd and the red line is 4 wd so is the 2wd solenoid stuck and preventing the 4wd one from pulling in or is the 4wd one bad ?
View 4 Replies-2003 5.4 XLT. 178,xxx Disk brakes front & back.
Driving home from work, came to a long stop waiting for train. Started to drive away and my front right brake started to lock up pretty good on me. Drove it home as I was only a couple blocks away. Its just started to get above freezing here, and we've been between 0-20 degrees for a good stretch lately. That being said, I'm pretty sure it's my brake lines swelling with our "heat wave" of 35 degrees today. Also I've replaced the rear rotors & pads, as well as flushed the brake system a while back. Never replaced the front after purchasing used a while back, as they still had plenty of pad left.
Question : Purchased new front lines. Do the front calibers, "float" on pins like the back? (If so that may be my issue of the caliber getting stuck on the pins moving back and forth.)
At 178,xxx miles I'm going to replace the lines myself regardless of this outcome.
I was uber excited to buy my first brand new truck in 09..... Amount numerous issues, defective rear window (fought with ford for 3 years never replaced under warranty), sync issues draining my battery, multiple O2 sensors replaced, multiple lights replaced and a blown drive shaft all under warranty. Now my warranty literally just ended, years not miles, just rolled 36k yesterday, ran out 3 years in November 12, now I'm having break issues.
A few weeks ago while driving, I released the gas and truck seem to slow faster than normal. Seemed kind of unusual but also began to noticed a drag on my mpg, about 2-4 mpg difference, depending on highway or in town. Now 3 weeks later, I feel grinding under breaking. Now it's beginning to make sense. I figure probably a stuck caliper. While driving with head out the window , freezing in IL, by the way, seems to be the drivers front. Checked rotors, outsides only as there are the guards preventing me from checking the back side. No visual or touch grooves ground into the rotors from the pads being worn out. Best bet is its the back side of the caliper that is locked.
Question 1, does this make sense, only one side of the caliper locking up? I had a caliper lock on my old GTP but the whole thing locked up.
Question 2, do I just suck it up and replace the breaks my self, gf's dad is a manager at O'rylies so I can get anything I want at cost, or do I go back to the dealer and bitch about mechanical problems being constant with my new now only weeks out of warranty truck? I read some horror stories about clogged lines and numerous other issues causing calipers to lock. I don't feel like replacing my whole break system, lines, calipers and all just to make sure the problem is fixed. At 3 years this seems ludicrous.
I just hit a pothole on my way home just now and now my front right caliper is sticking. It happen about 10min from my house. As soon as i hit the pothole I can feel my truck pulling to the right and felt like there was some resistance when i was driving. I got home and peeked my head in the wheel-well and i can smell the brakes burning and smoking a little. How would hitting a pothole cause a caliper to stick. Is there anyway to unstick it or am i gonna have to change that caliper out...
View 8 RepliesIs this repairable or would it be better to just replace it ? Ive never rebuilt one of these.
View 11 RepliesI have the TyrolSport Brake Caliper stiffening kit on my R. My brakes were squeaking and I had not greased the pins in a bit so I thought that might be the issue. When I went to grease them, I notice one pin was completely loose. It was my driver front lower. I greased it and tightened it back up. That was maybe 2 -3 week ago. I checked again on Friday before my track day on Saturday and the same pin was lose. Not all the way like last time, but not locked tight. This one pin is the only one that seems to have issues. The other three are rock solid.
View 6 RepliesI'm in need of what's going on with my 2005 Toyota Camry 2.4L (American Build), Non-skid, on the front brakes.
About 2 months ago my L/F brakes just locked up. So, I towed it to the dealership to have the brakes looked at and worked on. They said my Camry was locking up because the L/F caliper is freezing up. So, what the dealership did is replace the 2 front rotors, new brake pads, and new calipers. Got the brake fluid flushed out, also. Now, after about a thousand miles later and about 2 months, the same thing is happening. The L/F caliper are locking up.
I brought it back to the dealership and they said NOW, that it's the "ABS Actuator Pump Assembly" and the parts/labor would cost roughly $ 1300 dollars.. Now, when they replaced that part. The same problem is still happening. The L/F caliper is locking up. Luckily, when it was locking up I didn't drive the vehicle to far to damage the brand new brakes that was put in the first place.
I read a reference to the front brake caliper bracket bolts being one time use torque to yield and must be replaced every time they are loosened. Is this true?
This is on my 06 F-350 in my Sig.
1997 F-150 XLT Extended cab. 4.6L VIN 6, 5 speed manual, 4x4. Replaced speed sensor on transfer case, speedometer is not completely dead but bounces around. Seems to be about 10 mph below actual speed. When I come to a stop say at a red light speedometer drops to zero at about 20 mph or so. Cruise also inop. It seems like whenever I let off the gas to stop or shift gears the speedometer drops down but then goes back up but not to the right speed. It has the mechanical odometer by the way. Everything else seems to be working fine. New speed sensor did not come with the plastic gear so I had to reuse the old one. Not sure if that gear was bad or not, but it was the pink one if that matters.
View 6 RepliesI have a 2001 ford f150 with a 4.6 liter v8, my ac compressor is completely seized up, I can't afford to replace the ac right now. So I would like to just get a shorter serpentine belt to bypass the ac for now, need to get a measurement on the shorter belt for my engine? and the proper way to re route the belt without the ac?
View 7 Replies2001 F250 SD diesel. Brakes have been working fine with no pulling. They just started to squeal recently so I knew it was time for some new pads.
I'm having a problem that seems to plague me often when I try to replace disc brake pads. I can't get the twin pistons to go back in to allow room to get the new, thicker pads in.
I unscrewed the cap to the master cylinder and used a spreading tool (that came in a brake kit from Advance Auto Parts) to compress the pistons. No movement.
I put a lot of force on it. No piston movement.
I unscrewed the bleeder screw and tried again. No movement.
My question is my abs light came on so I stuck my computer on it. Said right rear , we'll we all know on a 2007 6.0 f350 4X4, the there's only one sensor on the pumpkin, so I replaced it and cleared the code. Abs light came back on once I started driving, week ago my right front caliper stuck and got very hot, could that read bad for the rear of the front went bad? Will pull plug and make sure I didn't bend any pins.
View 2 RepliesI know this has been talked about many times and how to solve the issue but thought I would ask some other questions too. Earlier in the summer, I did grease the slider pins as preventative maintenance. I don't drive my truck all that much and when I used it yesterday, (about 30 minute drive) I came home to burning brake smell. I'm wondering if enough heat would cause the caliper to go bad? Should I just grease the pins again or change out some parts?
View 6 Replies03 f350 4x4. New front calipers and pads.
Wondering if there's a 'trick' to getting the front brake pads into the caliper . Those damn springs kept popping out. I'd get three of the four ends into place in the pad holes then one would pop out while I'm trying to get the fourth in.
After about a hour of trying every different way that I could think of, another set of hands came by and with four hands holding things in place, it finally did the trick.
2003 F150 4wd with auto climate control. My blower for heat and AC completely stopped working a few weeks ago. I have checked all fuses, i replaced the relay under the dash, i replaced the blower motor control module. I supplied power to the blower motor itself and it ran fine with no noises. I ran the self test on the controller in the dash under the radio and it passed. I am not sure what else to try.
View 7 RepliesSo I had the same , "noise" in the rear of my truck that i see other people having, at first I thought it was my tires, since I ran buckshots, so I switched over to street tires, and low and behold it sounded like I had buckshots still on the truck. So this thursday I pulled the diff cover off, and guess what i found!
The abs ring on the ring gear, was completely off , and the bolt that holds the pin for the spider gears was broken with just about maybe 3/8 to 5/16 of an inch left in the pin, right now i am still working on how to get that out of there.
also found a 1999 ford f150 2wd truck, 4.6 auto , that someone pulled a 1997 4.6 engine out of and put it in this truck and now it won't charge, and i think it's cause of the pcm needing to be reflashed. tested the alt, battery, everything is good, i just don't know if the pcm controls the charging system.
Pics will come soon of the differential destruction.
My 4x4 only locks in when i lock it in and then go drive around, and i know its locked in when it gets hard to turn on the road. So i stop and play with it in 4x4 to see if it will go into 4 hi and it does but then after about 5-10 minutes it disengages again. I've checked the top portion of my vacuum lines, replaced my actuator on the front diff and I've made shore that my selonoids are working, and they are. I'm lost.
View 4 Replies