Ford F-150 - 1997-2003 :: 2000 5.4L 4x4 - OD Hard Shift / Slams Into Gear When Give It Little Gas
Jan 23, 2015
I have a 2000 F150 5.4l 4x4. When I am going over 50 on the highway and I am in OD, if I let off the gas a couple of seconds later it feels as though the brakes come on because the truck slow down so drastically and when I give it a little gas it slams into gear. It feels as like there is a "gap" where nothing is engaged before it slams back in. This is a rebuilt tranny with less than 7K miles on it. I took it back once and they said it was the motor mounts. I had those replaced and still the same problem. I replaced the spark plugs 6K miles ago and the COPs 3K ago. There is 170K on the truck. I only drive about 8K miles a year.
View 2 Replies
Advertisement
I have a 2000 F150 with the 4.6L engine and I have a question about the transmission. When shifting from 1st to 2nd gear there is sometimes a little hard jump when shifting. All the other shifting through out the range is buttery smooth. The issue has been around for a long time and has never gotten worse. Is there anything simple I can do to fix this. Do those tranny additives work at all? Otherwise, I will just continue to live with it.
View 2 Replies
I have an issue to where every once in a while my truck will not shift and when it does shift it slams into gear, and my overdrive light flashes and then I'll turn the truck off let it sit and crank it back up and it drives fine and the overdrive light is off. It shifts normal and smooth other than when this happens. Not sure if it is my torque converter or maybe a solenoid or what. My truck is an 07 f250 6.0 with 192,000.
View 5 Replies
I just bought this problem child and I am having som trouble finding out why when you put it into Reverse it slams into gear hard enough that the nose dives down. I cant figure out why. Then RPMS are always low like 800 and it acts like its at 2500. It slamms that hard.
The 2nd issue is when I push the brakes there is a vaccum sound from under the dash and the brake pedal gets hard and the car does not stop well. I assume it is the brake booster but I have not tore the dash appart yet.. The RPMS dont drop out when the vaccum leak starts and thats what confuses me.
View 7 Replies
2000 Ranger 4R44e transmission.Hard shift from 2-3 gear and when i run about 35-40 mph and brake then acelerate it downshifts hard . Whats wrong with it?
View 14 Replies
I noticed my '99 started getting difficult to get in gear & shift, within a coupe of days the peddle was barely off the floor before it would engage. A day later it started 'creeping' if started while in gear. Replaced the master/slave cylinders with no change.
Is a clutch replacement the next step? Just thought I would ask before throwing money at it, since the only other times I've had clutch issues there was slipping or it just plain exploded.
View 14 Replies
I have a 2001 Ford F-150 5.4L Supercrew that won't seem to shift out of 1st gear. This morning coming out of stop light on the way to work, the truck seemed to jerk when it was supposed to shift into 2nd gear. I was told by a friend that the speed sensor may be it?
So I took the truck around the block just so I can get a feel for what is going on. So the truck shifts into 2nd, but not past that. It seems that around 30mph the RPM's go up jump up quickly to 2k+ and no shift or increase in speed. I was reading up a bit on it and came across the possibility of a TPS?
View 5 Replies
I have a '97 F150 Lariat Ext cab, 5.4, 2Wd, 175K, a bit rusty but for the most part functional. Unit is parked for long periods of time.
3 - 4 years back the gear shift did not want to go into PARK and and the gear indicator was out of register. Unit would not start and I had to move shift lever to N to start. Fixed the two screws on shift plate/column per this site. Then 18 months ago same thing begin to occur but this time I used blue thread lock to hold screws in place. Still had to throw into park to get it to stay.
6 months ago shifter became very difficult to move and near impossible to get into PARK. When in PARK the interlock must have not been engaged so had to move to N or push lever hard into PARK to start.
Tired of this so I cruised the site and found several posts on taking dash apart, repairing a broken shift tube and or replacing bushings.
Battery disconnected, dash apart, cluster out, steering wheel still on and steering column still in position. Shift tube appears OK, i.e. not broken as in one post, bushings appears OK as there is no play or slop evident, but I cannot get the shift lever to move from PARK, period.
When the shift lever is pulled toward the wheel, a pawl on the tube causes a plastic or nylon arm to move about 90 degrees. It must be a stop or safety of some sort. I have not dug deep enough to see the shift plate with the two screws. At 75 I find it difficult to lay upside down to reach and hope I can get to them from the top.
Questions:
1. How do I get it out of PARK to check all things on shift tube and gear selector units?
2. Does the battery need to be connected for the interlocks to function?
3. Do I need to drop the column to check on shift tube items?
4. With a rusty trans, can the shift cable to trans connection be the problem?
5. What to look for, how to repair. etc.
View 7 Replies
I just bought a f150 2001 5.4L crew cab. It has the O/D switch in the gear shift lever and the black plastic handle is broke. I found a complete replacement lever on ebay but cannot find any tutorials on how to replace this.
View 8 Replies
1997 F150 xlt 4x4 ... When I shift the gear shift lever to below D (2-1) it blows a fuse and I lose instruments. Replacing the fuse is not difficult, just tiresome..
View 6 Replies
My 4r70w is having some issues. It drives/shifts fine in reverse, 1st and 2nd but wont shift past 2nd gear. Doesn't even act like it tries. No CEL. I dropped the pan yesterday and there wasn't any metal chunks or any other debris in the pan and only the normal fuzzes on the magnet and there wasn't even an abundant amount on the magnet. This is a junkyard trans that was put in before I purchased the truck (2001 F150 supercrew 2wd).
I've ohm'd the shift solenoids and they seem to be within spec (below 30 ohms) so i want to rule them out, but still thinking of replacing all 3 solenoids just to be safe. Also, the filter just fell out with the pan so I'm assuming that might be part of the problem. My next thing to check is the 2-3 accumulator and spring to see if its stuck or broken.
View 2 Replies
4R70W. This one is in my 99 F-150 with the 4.6. From what the previous owner told me this trans only has 13k miles on the rebuild and I believe him because the converter is bright blue and when it does shift right, the shifts are solid and fluid is very clean. Truck only has 98k miles on the body as well, so it's possible the truck did sit a while because my tires have a ton of tread on them, but they are dry rotted a bit (dated 2006 IIRC).
Issue: When the trans is cold (sat overnight) it will shift to neutral between the 2-3 shift for 1-3 seconds depending on outside temperature and then drop into gear. But it only does this for the first 30 seconds or so of driving, after that it shifts normal (although it does seem to hold gears a little longer than I would think it should on occasion and not upshift). I have only gotten it to do it once per cold start so it seems like once the trans gets any heat it's fine.
I was also thinking I was getting drain back and maybe it wasn't heat related so I dropped the pan, replaced the filter, fluid and pan seal (it had a small leak) and torqued the valve body. Two of the bolts were a little loose, but the rest were fine. Tightened them to spec and put it back together with no dice. Truck also gets pretty bad fuel mileage so I'm starting to think maybe there is some temp sensor screwing everything up?
View 12 Replies
I have an early 99 F250 4x4 7.3L..... 4R100....
Brief history, a while back on way home from work I let off of the accelerator and had a loud gear meshing like grinding noise, got back on the accelerator and went away, let off and back, so I quickly stopped and pulled over, went through the gears and reverse, everything seemed ok,??? went on my way, got home parked the truck and went about my evening. came out next day to leave and truck wouldn't move in reverse, forward but not reverse. long story short I was told that the snap ring internally probably came out, I have heard of this being a big issue with these, so I set up for it to be rebuilt, got it back and installed and still same issue, what the crap so I ended up having to pull it back out and amongst my own trouble shooting I found the simple issue and was the nylon riders on the 4hi/4low shifter fork were completely gone and allowing the planetary group to free float in and out of 4x4 neutral!!! NOW on to the issue at hand. so far only thing has been done is rebuilt and those fork riders replaced.
now I can move but 2-3 upshift under a load(more noticeable) has a delay going from 2nd to 3rd and under a load it hits hard. I talked to the guy that rebuilt it and he said that the rebuild kits don't always the right springs for the valve body and causes shift issues, so he talked me into the shift corrector kit which I researched and did see what he was saying, so had that done and still no better, still does it, however, it does shift into the gear softer but didn't fix the delay or the hitting hard when it did finally go into 3rd.
After being forced to drive it that way I have since determined that what it happening is it is coming out of 2nd with a second and half pause and then shifting into 3rd, the hard shift comes in to play because during the delay the torque convertor is locking up making it a direct drive like popping the clutch on a standard!!!
I just swapped out the sol pack and I heard from a youtube video that the bolt next to the 2-3 upshift valve on the valve body could be to tight and making a sticky valve, so I re-torqued all the bolts and nuts put all back together and test drive proved to be worse, I now have same issue in all upshifts. all hit hard now, I am at a loss and don't know where to go from here, I can only imaging the sol pack is causing this but I have yet put my org one back in to see... oh and I found two bolts on the accumulator stripped and found one non torqued bolt on the main valve body!!
View 2 Replies
I have been having an issue with my 4-5 gear shift under hard acceleration and know that a rebuild is due soon but I was wondering if any high performance kit available with all the clutches and friction discs needed to rebuild.
View 6 Replies
I have a 2002 f150 with a 5.4. It runs bad but all the data looks good. When you rev it in gear it revs sluggishly but when you put it in drive and give it any gas it will stumble and try to die. Un plug the tranny and it revs great and when in gear it runs great, but it obviously is stuck in second gear. I have codes for tcc short, solenoids a and b short, tcc short, and pressure control solenoid. I have replaced all of these parts inside the tranny including the wiring harness and main connector (transmission side). The OD light is also flashing. I Have run out of stuff to replace, obviously its something transmission related if the truck runs fine with it unplugged.
View 1 Replies
The truck:
2000 4X2 F150
4.2l V6
280k miles/ some towing
The problem : The trans has a hard time getting into 1st gear. When you put it into gear you have to rev it to about 3k (when it's warm, 4k when cold) RPMs at which time you feel a definite engagement and it goes through the rest of the gears just fine. Once it's warm it will do stop and go traffic as long as you start it with the OD off.
The background : Orobably the stock motorcraft filter on there, and I don't think the oil has been changed in the life of the trans, but I do know that it's never been ran low on fluid. I took a gander at it and found a plug where a gear type speedo went on older models to be loose and leaking. tightened it up about two full turns. also noticed what looks to be a leak where the main case meets the output shaft housing. now I know neither of these are the cause of my headache but I do wonder if the second leak might be a sign.
The research : I've been looking for almost a week now for a solution. I've been all over TCCoA, Explorer Forum,10 pages of search here on FTE and various other Ford based websites and have come across a single thread with the same symptoms but the OP never came back with a solution.
The plan : A fluid/filter change (and flush) is definitely in the plans as well as inline filter for my own satisfaction. from what I've read the stock 1-2 accumulator is known to go bad on some of these and if I have the pan off might as well check anyways.
View 7 Replies
Could my brake issue be related to my transmission problem? Neither are constant. Brake problem= sometimes the brake pedal feels hard, like there's no power brakes (I drove a car once. ..looong time ago. .. that had no power brakes or steering) but it will kick in after a short distance. Transmission prob= seemingly unrelated, is a problem shifting from 1st to 2nd gear. This has happened maybe a 1/2 dozen times, the first time and mostly when in heavy commute traffic and when going between 1st and 2nd gear because of the slow commute speed, but also at other times when not in lengthy slow commutes. When it doesn't shift, the odometer doesn't work (shows only dashes) and an engine light comes on (the sprocket/gear looking one). Usually the transmission will eventually shift and the light goes off.
I read that the brake problem might be a vacuum hose problem? Something about a booster? Is this dangerous? or is it like having a car w/ no power brakes? Going to have my transmission looked at this week. Read on another site about dropping valve seats on this year car. If there's a major transmission problem, I'm wondering if it's worth fixing? I changed, timing belt, water pump, front and rears brakes, tires. 143,000 miles.
View 1 Replies
My father's 2000 F150 5.4L has developed an issue. But the issue only surfaces in it's last gear. As it shifts into overdrive it begins to miss and hesitate and bog. If you disable overdrive you never feel it.
I'm thinking an exhaust restriction. There are no trouble codes, no check engine light. I notice that the note of his exhaust changes as the vehicle warms up, sounds like it's being smothered. And the flow out of the pipe lessens.
My only issue is whether the EGR is causing it or the converters. Haven't seen them go bright red yet, but this has been going on for a good while.
I wanted to get a few opinions before I tear into it today. I'll do a vacuum test on the EGR valve and rescan the codes but don't wanna drive it and heat up the exhaust when i gotta disassemble it.
View 4 Replies
The Speed Needle works fine. But...the Odometer part quit some time ago. I can't tell what my fuel Mileage is now. How to troubleshoot this problem?
Things that might affect this problem; Transmission skids loudly when going in and out of 4-OD. It could be the Torque converter clutch?
The Gear shift lever is sloppy. Doesn't fill me with Confidence.
Brake fluid warning light is on most of the time. Fluid level is up hi though. Driver door mirror control switch don't work in one direction Who on this Forum has a Switch for me?
View 14 Replies
Why my car is grinding gear when I shift from 1st to 2nd, & yes the clutch is fully depleted and still grinds when I shift.
View 4 Replies
My 2003 made a sharp mechanical noise one day, next thing I knew it lost the ability to shift out of 2nd gear....Now, it can still shift into 2nd gear when cold, but only after holding rpm for a bit and then suddenly jerking into 2nd gear. Once it's warmed up for a few minutes though, after dropping out of 2nd gear, that's it! Then it's stuck in 1st gear the rest of the time. Reverse doesn't work anymore at any time, and it gave me code P0732 to P0734 which should be gears 2 - 4. Is it possible that not being to get out of 1st means 2nd gear is broken, but the other 2 are okay and it just can't get shift past 2nd? Or might all 3 have problems after all?
View 1 Replies
