Alright so I have an 03 5.4 with 144000 miles. once it warms up to temperature it has a miss and low end power is low and no fuel mileage gets 12 to 13 if I'm lucky. From idle to 3000 rpm its doggy get it over 3000 rpm it runs great. All new plugs and coil packs. What it could be. When the motor is cold it runs great has most its power.
View 3 RepliesI recently inherited a 99 Expedition 5.4 with 90k miles. I'm trying to fix it up so I can sell it. Like the title states, the truck runs rough but there's no check engine light on. I did some research and ended up replacing the PCV elbow and that made it run better for a while but now it's back like it was. It won't die, just a really rough idle and a miss while driving. I imagine it's probably a (or a few) coil pack(s), but I have no way of knowing which one(s) to replace. I would think that would illuminate a CEL though. I'm also having problems with the AC. Upon inspection, I found that the compressor clutch assembly was completely gone from the front of the compressor. I replaced the whole clutch assembly, then voided the system of Freon and refilled it to spec, still no cold air. The compressor clicks on and off like it's low on Freon but it can't be. I'd just sell it as is but in south Louisiana a working AC is a huge selling point!
View 1 Replies2003 F150 5.4 72852 miles
I have a Rough Idle & sometimes a hesitation or stumble on acceleration. I cleaned the MAF & IAC motor & Air & Fuel Filters are new. I got a 20890 scanner & ran test 6 53 as suggested in many posts by BlueGrass. Here are My results & what They Convert to.
1 00F5 .3675
2 0051 .1215
3 0000
4 0000
5 00A3 .2445
6 0000
7 0000
8 0000
I'm guessing the cop's are ok & probably need plugs? I was hoping to just swap a coil. Too cold to do plugs & truck won't fit in my garage.
1999 F-150 5.4L. I just removed the clutch fan and installed two electric fans about two weeks ago. The same evening, I took a short drive and noticed the idle was way higher than it normally is. Its idling about 800 to 900 RPM. Now, the weird part.....Startup is normal, as in the idle jumps up for the warmup, then drops to the normal 600 to 700 range. after a short drive, the idle is high and noticeable at a stop.
Sometimes, if I let the truck idle, after about 10 mins or so the idle will slowly start creeping up a little at a time till it hits about 900 or so and will level off. I have tried the IAC, I have tried disconnecting the battery and letting the PCM reboot, I have checked ALL my vacuum lines, I have checked my TPS sensor and voltages, checked my MAF sensor and voltages, fuel pressures, everything I could think of...
I hooked up my scanner (Auto X-Ray 6000) and checked all my running data, nothing really sticks out to me as outta whack. No codes set..
I just installed glow plugs, ucvh, stage 2 rosewood injectors, t500, ipr and gear head tunes. I have out 97 miles on the truck since all this was installed and the truck seems to run okay but has a rough idle and sounds like there is a mis? What should I look into first?
View 12 RepliesEarly 99 7.3. Runs ok has a slight miss at idle however every injector when unhooked makes a change. Has white and blue smoke From the exhaust. Has enough blow by to blow the oil cap off as your unscrewing it. My question is, I know engine restore is bad for these trucks but I can't afford to rebuild the engine. If I run the restore and then clean the IRP once the truck dies is this going to mess anything else up. Do you think it will by me a few months to save up for a rebuild
View 9 Replies1997 F150 4X4 4.6 engine with 285,000 miles
Truck was running perfect down the road, then suddenly it lost power and started missing at all RPM ranges. So i keep driving another 6 miles and then POOF the miss is gone and truck runs perfect. Couple hours later i hop back in it and its running good and then suddenly it starts missing and loosing power again except this time it never started running good again. Never did throw a CEL.
I hooked up my SCT Tuner (for my F250) to check for codes and came up with P0171 which indicated one of the banks was running lean, but no missfire codes. Did a search on here and learned the common problems(vacum leak) of that code.
Found the vacum leak at the PVC elbow, so i replaced both ends of the plastic tube.
Pulled the throttle body elbow and cleaned out the clogged up EGR ports.
Put a new air filter in and took the MAF out and cleaned it with MAF cleaner.
Put it back together and it idled way better but still ran like crap with the bad miss/sputter. Ran it down the road a few miles and came back thinking of the catalytic converter, i crawled underneath and it was glowing red. It does run and feel like the converter is stopped up but if i have a dead miss and dumping fuel wouldnt that make it glow red to or no? Still no CEL and now no codes.
Also i held the engine at about 1000 rpms where i could here the miss good and unplugged the fuel injectors one at a time to see if that made a difference. Each one i unplugged made it miss worse, so wouldnt that tell me that all 8 cylinders are firing?
And i changed the spark plugs (motorcraft) 250 miles ago.
So it still cranks and runs smooth after a cold soak overnight and then after a mile of driving or less it starts the dead miss/sputter and loss of power.
2001 V10 160000 miles.
1st happened Wednesday on way back. Temps all fine but had been in stop and go traffic earlier. Truck was on cruise and felt like fuel cut. I disengaged cruise. Throttle would keep it running and within 5-10 seconds it caught and ran fine.
Connected and reconnected all injectors, coil connections, tb and MAF connections. Nothing noted loose. No codes on OBD reader.
Drove around town last couple days no issues. Today towing three dirt-bikes about 45 miles. towards the end of the 45 miles. she stumbled as we crossed an intersection. Then caught and ran fine. Did it twice on way back home towards the end of the trip.
Had OBD reader in gauge mode with ignition advance, tp sensor, voltage and gallons per hour showing. None seemed to change when it stumbled.
Fuel pump is about 2 years old. Coils maybe 4 or 5 years old. Aftermarket. No codes on OBDII reader.
I have a Tymar intake, magnaflow exhaust, a DP Tuner and I have Rosewood Diesel injectors.
I had a bad oil leak recently and it seemed to be coming from the turbo area so I changed all the o rings back there and deleted the EBPV system (I cut out the butterfly and welded the holes shut, cut the part of the pedestal that held the actuator because it looked like it was leaking and welded the oil holes in the pedestal that fed it. I left the actual EBPV sender in the pedestal and kept it connected to the harness)
After all that was done I checked the oil and it was low but still on the dipstick so I drove it to the local parts place to get some more oil, about 2 miles, because I wanted to check for leaks. It was not happy, ICP low code came up it was sputtering and jerking when stopped at a light. I got to the store and parked it, it took about 3 litres of oil and seemed to run pretty good after that.
But on the way home I noticed a bunch of white smoke, I figured maybe an injector was stuck. I started it a little later and no white smoke in the driveway so I thought maybe it had gotten lubed enough and had sorted itself out. That was a few days ago.
Today I started it and let it idle in the driveway for about 15 mins and no white smoke, I wanted to get it up to speed a little so I took it to do an errand that was about 10 miles away, lots of lights and a bit of highway. It would run fine while going at speed but as I would slow down for a light the ICP would go down to around 600psi and the white smoke would start, as sitting idling a huge cloud of white smoke would form (yes, I was that guy), once I could take off and get it running a bit harder it would go away again.
I am assuming that I have a stuck injector (or cracked), I have no oil in my degas bottle and it doesn't look like it is fuller than before. Seems like I may have used more fuel than I should have, but pretty hard to tell just from the fuel gauge.
I have tried a buzz test and they all sound the same, tried a Compression Contribution test, no codes from that.
How can I locate a stuck injector? If that's what it is?
I've been working on my truck for months now on and off. I thought i finally had it back, but i have (again) problems with running. it basically only ran for a full day (hauling trip) after getting it back up and running. next day, it died on me on the road.
The new deal right now is that I can make the truck start and it will run, but it has little "hiccups" or misfires that will happen every now and then. Once it gets warm enough, the idling sounds chopped (best way i can explain it). After "chopping" it will then run fine (until the next chop). then it seems that once the truck gets warm it just stalls out. When that happens (shutting off) i can't get it to start right away. i have to wait awhile before it'll start and that lasts only so long.
The truck puffs a tiny bit of white smoke. not constant but more like a "puh - puh - puh" ....I've changed out quite a bit of used up parts now...
Turbo
Injectors & wiring harness
valve seals
IDM
ICP
IPR
CPS
MAP
fuel pump
vacuum pump
glow plug relay
starter relay
All the sensors are OEM. There's fuel in the fuel bowl, and the filter is clean. Plenty of oil in HPOP & oil level in crankcase is good. Have plenty of fuel.
Air filter is clean and fine. No codes. No lights.
2001 f350 7.3 320k on it.
I have a 2004 Ford F250 with 174,000 miles the truck has a slight miss a rough idle one hot or pulling I have 2 codes nut no light when I go into the ford oem feature in my scanner a PO 272 and a PO404 .. Where to start?
View 4 RepliesI have a 97 f150 with 4.2 4x4 auto. I have a bad miss under acceleration. if i ease on the gas no problems. stomp it and it chugs and pops back thru airbox til it gets to 2500 rpm then clears up. If I shift it manually and keep rpms up its fine till it gets below 2500. I have replaced spark plugs, plug wires, fuel filter, upper and lower intake gaskets, cleaned injectors, new air filter and cleaned o2 and mas sensors. Had vacuum system checked and was told all good.
View 12 RepliesMy dad has a 2000 F-150 with the 4.6L with 90,000 miles. He just had the transmission rebuilt 5,000 miles ago if that. It seems to miss between 45-55 mph when you have a little hill and give it some gas. Once its shifts out of over drive, it seems to be better. With over drive off, it does not miss as much. I know we put new plugs in it but don't remember how long ago it was. He bought the truck brand new.
View 2 RepliesMy 01 Super Crew 5.4l is missing at light throttle. Cruise control on flat hwy, no miss, slight incline, starts missing. Put my foot into it and either it stops missing or it covers it up where I don't notice it. No codes set at this point. It's got about 135k on it and for all I know it may have had the original plugs in it so I figured I'd change them. Changed the plugs, still misses. Shortly a code set, something about the EGR sensor (it's got another name but I forget what it is at 1:30am). I found I had broken a hose while changing plugs, fixed it, no more code, still misses.
When I sent my GF up to get the non-existent codes checked the parts guy sold her some Lucas fuel system cleaner. I'm figuring a COP going out but the cleaner pretty much completely fixed the miss, till that tank of gas was gone. Few tanks later and it's back again as bad as ever. I bought some seafoam as I've had good luck with that in the past. It almost completely fixes the miss but I get a rare 'bump'. What do I need to look at next? Can it be the fuel filter? I'd think no because I'd figure it'd be even worse at greater throttle opening. Injector? How do I check them?
I've had good running on the truck but lately in the cold the idle has a weird skip to it like it's missing on a cyl. It will start fine, and run fine for about 30 seconds. Then it will start to mis. When giving pedal it goes away and it's driveable but it doesn't sound right. After a bit of running it's fine for the duration while warm. My monitors are I think all good, 48.5v, icp about 1250 psi. Is this the famed "injector stiction"?
View 5 RepliesI have a 97 f 150 with the 4.2 bad miss on # 6 changed plugs and wires still missing. Also have a bad tick and exhaust smells like fuel. Check engine light is blinking.
View 10 RepliesMy father's 2000 F150 5.4L has developed an issue. But the issue only surfaces in it's last gear. As it shifts into overdrive it begins to miss and hesitate and bog. If you disable overdrive you never feel it.
I'm thinking an exhaust restriction. There are no trouble codes, no check engine light. I notice that the note of his exhaust changes as the vehicle warms up, sounds like it's being smothered. And the flow out of the pipe lessens.
My only issue is whether the EGR is causing it or the converters. Haven't seen them go bright red yet, but this has been going on for a good while.
I wanted to get a few opinions before I tear into it today. I'll do a vacuum test on the EGR valve and rescan the codes but don't wanna drive it and heat up the exhaust when i gotta disassemble it.
2005 6.0l - codes are P0261 Cylinder 1 injector circuit low. PO263 Cylinder 1 Contribution/balance and PO270 cylinder 4 circuit low. Ficm still reads 48 plus or minus .5. What is really puzzling is how changing the oil cooler and the EGR cooler would create these problems. Did I screw up the injector harness. Vehicle does not smoke either white or black. Low idle miss and at 55 it chugs once up to speed. Don't want to go Ford if I can avoid them. Whats going on.
View 7 RepliesEngine will start and run but will miss in a pull and die sometimes but will start back, we hooked it to a scanner and it said (intake wiring) it wasn't a dealer hook up just a gas station garage, we have already done plugs and wires.
View 2 RepliesI drive a hot mess of a vehicle. It is a 1997 for taurus that's got more than its fair share of miles on it.My big brother drove this car when he was 16 and I am 22. I am a college kid and I don't do much to my car knowing it will die soon but at the same time I don't have much money to do much. We have a good relationship most of the time and I gladly provide gas and regular oil changes in exchange for transportation.
My car when its warm outside especially idles very rough. So rough that at times it stalls out. It seems to happen most often and to the worst degree when the outside temp is very high and it has been running recently and I'm trying to start it up again. At other times and temperatures it has idled rough but not bad enough to stall. Once I start driving, or moving, its fine. The rough idle makes my car sound like a boat, that's the best way I can explain it.
Why my car does this? How to fix it?
I have a 85 bronco 2, but i have no luck with responses in Bronco 2 forum, so here goes. It is the 2.8 carb, manual trans with 109K miles. Idles really well some hesitation when taking off but really bad miss and not power under acceleration. KOEO codes are 31 and 84 CM code 18. I have plugged the vacuum line to the EGR and have noticed a dramatic difference. I have tried to rev the engine and check the vac line to the EGR but I do not feel any vacuum, and at idle the vac line on or off doesn't change things. Any recommendations to whether it is the Sensor or the valve itself and what gives with the 18 code. I am hoping to have timing checked by the weekend.
View 2 Replies