Ford F-150 - 1997-2003 :: Pedal Was Rock Hard When Hit The Brakes Coming To A Stop Light
Apr 24, 2016
I have a 1997 F250LD 4WD. I was driving and came to a stop light. I hit the brakes and the pedal was rock hard with what seemed to be very little travel. I pushed hard to get to a stop and the abs activated and I came to a slow stop. This has happened about 3 times over the last 1000 miles of driving. I see no ABS or Engine lights. Most of the time the brakes are normal. Pads are fine, fluid is fine. Brake booster seems to work fine, pedal is not mushy or hard to press other than the 3 or so times this has happened. Once this happens I can let off the brake and everything is normal. I have not found any vacuum leaks.
View 6 Replies
Advertisement
Have 65k now..OEM breaks. Never an issue.. going along today had to make a fast turn left into a parking area. Hit the brakes doing about 50 made the turn. Slowly found and kept rolling to a parking spot. Went to apply the brakes and found the pedal was rock hard. The truck kept rolling slowly. Pure luck I was were I was.. I tried to shut the truck down and restart. Still rock hard pedal in up position. No breaks.. not enough to stop at idle. Checked the brake fluid and it was fine. Went inside the store to grab the delivery and when I came back out I tried to work the pedal down.. I felt some give.. put it in reverse to check it out..(couldn't go ahead no room.) slowly the breaks came back. Has been fine since.. driving all over town today. No codes or engine lights.
View 14 Replies
I have a 99 F150 4x4 (5.4) 173k miles. I bought the truck from family about 6 months ago and from time to time if you stepped on the brake pedal to hard (not locking up, but pretty hard) it would feel like the passenger rear tire would lock up. He said that there was an issue with the automatic adjuster on that side. Here lately the ABS light on the dash has been coming on every couple of days, of course on the next restart it's off. Could these two issues be related?
View 3 Replies
Can get up to speed about 55-60 in my 2003 f250 6.0 4x4 truck and hit the brakes hard and the pedal gets hard almost like you cut the truck off and the truck doesn't stop well I can let off the pedal and hit it again hard and it works like it should. Also when it does this the power steering doesn't work. I was on an exit ramp and almost wrecked when I exited off the interstate I hit the brake pretty hard and couldn't steer I let off the brakes then hit them again and it worked fine and so did my steering. It would seem that the two are connected somehow. What's wrong?
View 2 Replies
I have a 97 F250 that is having reoccurring brake issues, It has an intermittent hard pedal with little to no brakes when it occurs. It will stop but you are standing on the pedal with both feet. I have replaced the booster, master cylinder, and the vacuum pump in the past trying to isolate the issue and still had the problem. On this year model the abs ids only on the rear correct???? if it is shouldn't it only be affecting the rear brakes? Since this truck has a dual reservoir MC the front should still work?
View 4 Replies
So since I bought the car several months ago, I have been noticing something about the braking. Every time I get in the car the brakes are ROCK hard until I start the car, this seems abnormal to me, I never experienced this. That is not the only problem, when I am driving down the road and go to apply the brakes there is a hesitation which causes me to press harder and then the brake kind of slam on. I know its under warranty but I hate taking my car to the dealership so I'd like to know first that its a legitimate problem before I take it to VW. I know about the Hill assist, this isnt part of the issue.
View 24 Replies
My brake pedal is rock hard to press and when I do press it while pushing the push to start, it does not turn on.
View 8 Replies
I have 2011 SE, it won't start at all. The car won't start all thou all electrical are working (radio, NAV, Dashboard) but when trying to press the break pedal is hard as a rock. Dashboard computer at times tells me to press the break pedal - but it wont start, it actually turns off when i press the break and hit the start button. It happen twice before was able to start it within couple minutes.
View 24 Replies
2004 Jetta 1.8 bought mainly as a parts car w /204K miles on it. Ran and drove fine, but the tranny had no 1st gear. Tried all sorts of things other than going inside the transmission and figured it is/was a bent shift fork. Clutch worked perfectly. Had another 02J tranny from 2003 1.8, so we swapped trannys. Could not get any response from the clutch.
Start the car in neutral and it won't disengage enough to shift into gear. Start it in gear with clutch pedal in and it is obviously slipping/burning/chattering. Have bled the slave cylinder to no end, have reverse pressurized it into the reservoir , etc, etc. Made up a block off plate to go over the end of the slave actuator and when the actuator is "blocked" from moving the clutch pedal is rock solid hard. Yet, the clutch acts as if the actuator isn't extending far enough. Have swapped out the original slave cylinder with the one from the '03, no change.
Removed tranny yesterday to check the condition of the throw out bearing and pivot and Pressure plate. All appeared fine. Reinstalled tranny and same issue.
View 10 Replies
2 questions regarding our 2001 F150 Supercrew. My 2 questions are:
My 2001 Ford F150 Supercrew (5.4L, 230,000 miles)has the check engine light on with the code reader telling me that it is the P0174. The truck would run rough when cold (usually in the mornings) and sometimes it would get close to stalling out when coming to a stop light. So we would quickly put it in park and give it some gas to rev it up a bit. After the truck gets warmed up, it runs great with no hint of the rough idle. Since this all started I have changed out the PCV valve and replaced the PCV hose (including the elbow). I have also replaced the Idle Air Control unit but that didn't really make a difference.
We then experienced a cylinder #4 misfire which we resolved by changing out the cop with a new Motorcraft unit. The misfire went away but we still had the problem of running rough at idle to the point of stalling out at stops when the engine is cold. A few weeks ago we cleaned the MAF sensor and that seemed to work. The truck doesn't run as rough now (when cold) at stop-lights, but occasionally it will still have the loping idle. We cleared the check engine code and it stayed off for about a week before returning.
I don't know what else to check other than trying to see if there is some type of vacuum leak, but I don't have access to a smoke machine nor would I know how or where to hook one up. Removing and cleaning the throttle body would work? What could be causing the trouble, or what I should do to further isolate or troubleshoot the problem? I saw a you-tube video on the F150 intake manifold gasket possibly being the problem and although I hope that isn't the trouble with my truck, if it is then I will have to deal with it. We need the truck to get to work and the car is now due for a registration renewal, but we can't get a California smog certificate with the check engine light on.
View 3 Replies
I bought a 97 f150 4x4 last week. I was cleaning the frame up with a wire brush on a grinder and accidently cut one of the front brake lines. Seeing how this truck has only 100k on it and all oem stuff on it, I decided to replace the front brake components, calipers, pads, rubber and steel lines. Got it all back together and bleed the air out of the front brakes. But the pedal still goes to the floor. I can pump them up with the key off but when i turn it on the pedal goes to the floor. I did not bleed the back brakes becasue I assumed that the master cylinder would be divided and independent of each other- back and front. So it this just that the back brakes needs bled or do I have another issue like bad booster- everything was working well before I cut the line?
View 6 Replies
When coming to a hard stop and downshifting using engine braking, is it normal to have the brake pedal feel like it loses pressure to where the brake pedal pushes down further towards the floor for a split second? What causes that to occur?
View 10 Replies
My son just bought a 97 F150 with the back brakes blocked off. The front brakes had about full pedal when the was on. We changed the front calipers and brake pads. Bled them came back with great brakes (with back brakes blocked).
Then we found out the back calipers was none so we bought all new parts for both back brakes, found some leaks in the rear lines fixed them. Now we bled the brakes with the motor off till no air came out. Solid pedal. Then turned on the motor and the pedal goes down 3/4 of the way now easy.
Stops on snow good no tire sliding. Turn off the motor has solid pedal again.
View 2 Replies
So the other day I slammed on the brakes when traffic came to a halt on the highway. As I slammed down on the pedal, all the sudden the pedal lost pressure and went nearly to the floor, but firmed up just before bottoming out. My brake and ABS lights went on as well. Someone told me there is some kind of failsafe that blocks off the line if it ruptures, so maybe thats what happened? The brakes seem to work fine and are not loosing any more fluid, but the warning lights remain and the taillights do not light up.
So when I got home I took a look. On the fender side under the fuse box there was a lot of brake fluid, and looked like the line going from the master cylinder down to some kind of module (abs thingy?) below it was all rusted.
Today I replaced the line, and bleed the rear brakes. There did appear to be a ponhole in it, right where it would have been spraying the fender side where I saw all the fluid. The pedal is very firm right from the get go and brakes seem to be working fine. However the brake and ABS light remain, and my brake lights still dont come on when I press the pedal. Do I still have a leak somewhere or is there something else I have to do to clear the warnings and get my lights back?
View 11 Replies
I just joined as I bought my '97 F-150 5.4 4X4 about 3 months ago. The dealer gave me a 6 month warranty but hasn't honored it at all and I've had one problem after another. That's another story though but right now I'm just trying to fix the important issues. The problem at hand are my brakes.
I was noticing a couple days ago (maybe I never noticed it that much as it was a new vehicle to me) that when I apply the brakes it sounds like a bicycle pump and the pedal travels nearly all the way down. It doesn't hit the firewall but I'd probably guess it has 3 more inches or less until it bottoms out. The hissing only occurs as the pedal travels and stops when the brake pedal isn't moving.
Now I'm not sure if the hissing sound is normal as I replaced the brake booster (from the junkyard though) and the new one still hisses when I apply brakes. The brakes seem to work okay, could be more sensitive it's just the pedal feels soft until it almost bottoms out like I stated before and the the brakes grab a little bit harder. What could it be?
View 2 Replies
After replacing my brake pads and shoes I am hearing a squealing noise coming from the area near my brake pedal. This noise sometimes becomes high pitched if I depress the brake too hard. I am also losing a little bit of brake fluid if I depress the pedal hard several times. The brakes themselves function fine and have no problem stopping. When I bled the brakes today some of the fluid was black. I figured it might be air in the system but after bleeding them it is still happening. I also replaced the bleeder screws.
1997 Pontiac Sunfire 2.4L uses DOT 3 brake fluid.
View 6 Replies
01' Screw 5.4 4wd. Went camping this past weekend and it was the first outing for this truck our TT weighs 6k. When accelerating from a dead stop going straight I'm getting a rumble strip like vibration that last a second. If I take off very easy it doesn't do it. I've seen similar post but no definitive solutions. This truck has less then a 100k on it and so far I've changed the trans filter/fluid rear end oil with modifier and new spark plugs.
Once I'm rolling and hammer down it won't do it. It's more of a annoyance then anything.
View 9 Replies
I have a 2003 F-150 4x4 with cruise control and 4-wheel disc. When I am at a stop light for a while, when holding the brakes, the pedal slowly begins to fade towards the floorboard. I have replace two master cylinders, the original and a reman and then put on a new Motorcraft one...all providing the same problem. I have been told by dealerships that it is my imagination or that this is a "normal" problem. Having my truck roll at a stop light while the brakes are applied is not normal.
View 8 Replies
On said truck, when you go to stop, the brakes grab a bit, then release , then the pedal goes to about 2 inches off the floor, then they grab and hold. Pumping does nothing. No abs light on the dash. Today we put the truck in 4high and while back up I had full brake pressure from the top. Also when you take off, either in the mornings or during the day, it has a slight vibration, kinda like a brake grabbing, then all is fine. The brake grabbing isn't there 100% of the time, I would say 95%. I haven't changed the brake pads, rotors, or anything yet. Just didn't want to throw money at it and still not fix the problem.
View 4 Replies
My 2003 windstar SEL needed new brakes and to have the rotors turned... instead I opted to buy new discs and pads online ... To my surprise the new discs were about a 16th of an inch thinner than the old.... I changed discs and pads and was happy for a few days, but now on occasion when coming to a stop the front brakes grind terribly....the next time i stop everything is fine...visa versa...dscs feel true (no pulsing) I DID APPLY BRAKE QUIET TO THE BACKS OF PADS....
View 2 Replies
I have this truck (in signature below) that I have not driven for ~3 years. As I am starting to drive it I am noticing I need to put A LOT of pressure on my brake pedal to get the brakes to work. They stop the truck and the pedal doesn't feel soft as if there is air in the line but it feels as if I apply a lot of pressure and there isn't a lot of grab.
While it might be possible, I don't think I have any type of glaze or coating on my brakes that would cause this. 95% of those 3 years, the truck was inside.
I wonder if it feels as if the truck is hard to stop because of the additional power I have coming from this new motor?
Is there any type of part I can replace in the brake booster to adjust the pedal? Or brake booster. Maybe that is going bad?
View 2 Replies
