Ford F-150 - 1997-2003 :: V6 Cranked Ok But Not Starting
Sep 10, 2013
2003 F150 4.2L V-6. Cranked ok but no start, no check engine light. Plenty spark and could hear fuel pump running. Thought it might be out of fuel but gauge showed over 1/4 tank . Added ~2 Gals fuel anyway, started immediately- no check engine light, no codes set. Thought- bad gauge sending unit. Dropped tank and found plenty of fuel and sending unit checks good. New pump on order but what else could cause the problem?
View 7 Replies
Advertisement
After the details below, the truck finally started & I let it idle over an hr. Then turned it off for the night. Just to check, immediately tried restarting. Turned over very fast. Started once almost immediately & ran for 1 - 2 sec, then died. After that it turned over fine, but no attempt to fire - just as it's done in the past.
2000 F150, 5.4 L gas. Couple weeks ago it didn't start. Cranked fine - no sign of starting. It did this once a couple mo before that - wife was shopping & didn't start at the store. By time I got there, it had started. Her "solution" was loosened / retightened the gas cap (no, don't know why).
Never found a problem - didn't do it again for months. Then it did. Figured a code scanner would show something relevant to starting problem. It didn't - as far as codes go.
Couple weeks ago, battery was NOT dead by any means, but slightly weak (hadn't driven for couple weeks). I charged the battery (< 1 yr old). Seemed to take charge OK - didn't take long. But, after charging, volts at the battery = 12.8v.
Is it possible that's too low for these trucks & cause starting problem? It turned over quite fast - still no sign of firing. Gas isn't old. New Autolite spark plugs. Clean air filter.
I decided then to use the "jump start" setting on my charger (2 weeks ago) - still didn't fire & made no difference in cranking RPMs. Jacked around that day a couple of hrs. Checked all fuses (inside & under hood).
Bought the scanner - needed one anyway. Actron 9580A. All it shows on codes is a problem ABS wheel sensor (C1230) and a non-MIL code:
P1000: "OBDII Monitor / Drive cycle test not complete."
Suggested fix: "drive vehicle until drive cycle test is complete."
I don't think that's keeping it from starting. No idea about the drive cycle test. The battery hasn't been disconnected OR dead since I replaced it. It's certainly been driven hundreds of miles since new battery. Right after reading the codes today, decided to try starting. Didn't turn over quickly - battery somewhat low after 2 weeks w/o driving.
Surprise - it started - though didn't turn over fast. I let it idle some, then started recording data w/ the scanner. Where a couple weeks ago w/ the engine turning over like mad, it wouldn't start or even fire.
Note: only real difference in today (when finally started) & 2 weeks ago, or the time several months earlier: today is much cooler - in the 60's - vs. 90's the times it didn't start.
So, right back at square one - no signs of what's keeping it from starting. Maybe need some instructions on using more advanced features of the scanner / recording live data (if it starts again).
View 14 Replies
I have a 2001 ford F150 with a 5.4 2WD, with a starting problem. Last Friday I went to leave work the truck cranked but did not start, turned the key off and tried again same thing, on the third try it started. Drove it home 30 miles with one stop on the way, restarted just fine. At home in the driveway I restarted it 5 times without a problem so I was thinking it was just a glitch. Did not drive the truck all weekend thinking the problem was fixed.
Monday morning leave for work and everything was fine, went to start the truck in the afternoon and the same problem as listed above (3 or 4 tries and it started). It home again in the driveway restarts every time. I do not have any check engine light on but I thought I would still plug in my code reader NO CODE. Where to start troubling shooting this problem?
View 11 Replies
1997 Ford F-150 4.2L V6... I got into my truck yesterday and went to turn it on. The motor cranked half way then quit. Now everyone time I attempt to turn it on all I hear is a click and nothing else. A friend of mine who is pretty good with cars took a look at it with me. He tested my starter with a volt meter and said everything seems fine. We proceeded and checked all fuses, non of which we found are blown.
We then focused on the starter solenoid. We were able to get the truck running by arcing the 2 lower big terminals. I purchased a new solenoid thinking that was the problem, however replacing it solved nothing. Same problem is still present.
I have now arc the terminals to get the truck started 2-3 times in order to get to a shop. They spent all day looking things over and are pointing the problem to a bad starter relay. (i thought the starter relay was actually the same thing as the starter solenoid) Anyways they told us they have looked over all the diagrams they have access to and cannot locate the location of the starter relay. (maybe becasue its the solenoid?..)
View 14 Replies
1999 F250 SD V10 I recently replaced the in-tank fuel pump and filter. I operated the truck briefly after and everything was normal. I parked it with about 1/4 tank of new fuel and put it on a battery tender. It was parked in a garage on level ground in temperate weather(Southern Calif.). Two months later I tried to start it and it acted like it did when the fuel pump was bad. Cranked fine but no hint of starting. Could it be the fuel lines have become full of air and need purging through Schrader valve ? I haven't begun to troubleshoot but what to check other than pushing the fuel relay reset button.
View 5 Replies
I have a 2009 Silverado regular cab 2 wheel, drive 6cyl with 30K kms on the odometer. Yesterday I went to start it and it barely cranked like the battery was low. I let off on the key and on the 2nd attempt it fired up as normal. Again this morning when I attempted to start it the same thing happened. The battery appears to have a full charge as the headlights are bright when the ignition is turned ahead. This appears to happen when the truck is cold or first started in the morning. Any known issues that would cause this? It sounds like the starter could be dragging but given the little use this truck has seen I am not leaning toward that cause.
View 12 Replies
Been awhile since I've been on here...guess that's a good thing! Current problem...about a week ago my car stalled after starting it. I had been running errands all day so the engine was warm. Started fine, and then slowly died. My husband replaced the IAC valve. (My truck had this same problem 3 1/2 years ago...it was the IAC).
After replacing this time, it seemed to be fine. However today, again after running errands, the engine stalled slowly after I had started the engine. It seemed like it was trying to stay running, but then just slowly died. I tried starting again and it stayed running, so I was able to get home. It seemed to run fine while driving home. Also, no engine light has come on. Wondering what could be causing this. Don't want to get stranded somewhere.
View 7 Replies
I have a squeal that I am pretty sure is coming from somewhere in the A/C compressor/pulley assembly. The trucks squeals on start up (more so when it is cold/damp outside) and then sometimes as I am driving. It doesn't matter if the a/c is on or off. I have also noticed that, while driving, the squeal occurs when I take my foot off the gas. At this point I have replaced the belt, the tensioner and the a/c pulley. I am about to change out the shims to see if that works, but also was wondering if it is possible for the clutch hub to wear down and go bad.
View 14 Replies
I have a 01 f150 with the 5.4. when it starts it takes a minute or two to do so.. After I shut it off and try to restart it won't unless I turn the key on and wait. I checked the pressure and when idling its running about 28 soon as the key is turned off it goes to 0. Is my pump bad??
View 8 Replies
1996 f150 sometimes it starts sometimes it don't. It is cranking over the starter is in gauging as well as the fuel pump I can hear it.... It's getting spark and I replaced the starter solenoid.
View 5 Replies
My 3rd gear is starting to slip, Is there a chance that it might be a small fix ? if so how or what can I do? 2003 F150 4x4 Automatic ...
View 1 Replies
Have a 1999 f150 replaced tranny. truck started out ok for first 10 miles now it putters when starting from stand still can not figure it out.
View 3 Replies
I got an 2001 f150 4.2l v6, 5speed. It started running real rough almost like it was hitting on only 3 cylinders I replaced the crank sensor and did a tune up on it along with a new coil pack and now it won't hit a lick the plugs are getting fire, it's getting fuel but, will not start it's not throwing any engine codes. Which leads me to believe it may have a bad ecm.
View 3 Replies
My 2002 Ford F-150 4x4 4.6L 5speed strangely has a time delay in starting now. A delay in TIME and not the usually chucking along waiting to start. Or simply I turn the key and a second or two passes before anything starts to happen and it fires right up. Was wondering a few months ago, if my clutch sensor was going out but then it cleared up once I put a new battery in it although at the same time the weather warmed also. Bad connection somewhere, bad ignition switch, or bad clutch position sensor – I could go in each of these directions. Thought maybe the security in the key was doing it too but both keys have the same problem. No codes also.
View 2 Replies
I am Hearing a series of 5 one second tones about 1 minute after starting. There is no indication on the dash that anything is wrong. There are five tones about one second long. They repeat five times and then stop. The truck appears to be running fine. What is this?
View 1 Replies
2001 F150 ... I'm having trouble with my truck starting after its been running for awhile and then I shut it off.... I have to let it sit for a few min. Before I can crank it again and it will start. I was driving down the road and it just died on me the other day that's what started all this...
The fuel pump and filter was already replaced and I just replaced the cam and crank sensors ... but its still acting up...... I'm not sure where to turn next... No check engine light ..... I have a scan tool and checked for soft codes but nothing.
View 5 Replies
Have a 2001 F150 5.4L Super Crew that hates temps below 50 degrees. It has new O2 sensors on the pass side banks, Map and Air charge temp sensors as well as a new IAC motor and a fuel pressure regulator. I've went though all the vacuum lines and replace the cracked dry ones as well a checked for vacuum leaks.
On initial start up, the truck will run and idle fine. after a minute or so, the rpm will fluctuate radically from 500 to 900 RPM. When driving, and you come to a stop sign, the engine will do the same almost seeming to stall. Once the engine reaches full operating temperature, then it runs fine. It always seems to throw P0171 / P0174 when it does this.
We've sprayed all around the intake and cannot find a leak anywhere. I do find it odd that this is a temperature related issue based on the engine operating temperature and the air temp in general. 50 degrees seems to be the turning point from running to just being a hand full until it warms up.
View 10 Replies
I just changed my 4.6L. Now my tranny is starting to serge and buck it won't go in rev. But when I put it in D it started to clunk and buck. RPM would go up speed went down.
View 1 Replies
I have a 2001 F150 XL, 2WD, 4.2L, Auto at work. It will intermittently crank but not start, also, my scan tool will sometimes not connect to the truck. The only code I ever get is 1 about not being able to connect to self diagnostics. I have narrowed it down to the PCM relay in the underhood power distribution module not turning on because it SOMETIMES only sees a 2 volt turn on signal instead of 12 volts. I have replaced the ignition switch on the steering column- initially I thought that took care of it.
But as I was about to put the meter away it did it again. If I remove and reinstall the diode that is in the PDM, sometimes more than once, I can get it to turn on. Are these diodes available from any one besides Ford? The wiring diagram in my Haynes manual is very generic and does not show the circuit from the ignition switch to the fuse box. Where can I find a GOOD and complete wiring diagram for free on the net so I can print it out and take it with me to work?
View 1 Replies
2001 F150 4.6 V8 Triton
Automatic
Battery Tests Good
Starter Tests Good - I saw it spin and come out at the testing station at Autozone
Ignition Relay (the one in the fusebox)- New (8mo.)
Switch on the firewall on passenger side of truck - New (8mo.)
Battery terminals/connectors - Tight, no movement, Cleaned within the last week.
Starter connections - cleaned within the last week.
I am having trouble with my truck not starting. The issue has been occurring on and off for over a year. Usually, it happens about once a month, regardless of weather.
I turn the key, and there is one click. Usually at this point, I can use one hand to gently pull the shifter "up" towards park and turn the key again and it will start. Recently it is not starting when I do this. I have tried many times, and have tried to start it in Neutral (is that even possible with an Automatic?).
With the key in the "ON" position, I go under the truck and jump the starter cellinoid. I am jumping the small post to the big post where th wire comes from the battery. I do not touch the post that the wire goes into the starter.
I am very confused because it starts just fine without fail and almost instantly when I jump the posts. It is drive-able this way, but I would like to resolve this issue, and resume using my key to start it since the issue doesn't seem to be resolving itself as it usually does.
A friend told me about the Ignition Starter Switch inside the Column. If I have time I will attempt to start the truck with a screw driver on the switch tonight to narrow down the issue.
View 9 Replies
I drive a 2001 ford f150 lariat 5.4L. My truck will crank but not start, i am getting complete spark, and have ran a full fuel pressure procedure, and am getting complete fuel pressure, there is no water in my gas, everything checks out how it should. I ran a test on my cluster and it showed a code that said i am not getting connection to computer to start. I removed the cluster and repaired all loose wires properly, and it still wont start! I have had many people look at it and they said it could still be a bad cluster.
View 13 Replies
