Ford - F150 :: After Stopping The Truck Will Not Shift Into Gear
Feb 25, 2014
I have recently purchased a 1999 F150 with a v-6, standard transmission (5 speed). Previous owner said he had just replaced the clutch. Here is the problem, after the truck has been running a while and after stopping the truck will not shift into gear. It does not grind or make any noise, it just won't go into any gear. The only solution is to shut the engine off, place it in gear and restart the engine. During normal travel the transmission shifts up and down without any problems. The clutch does have a slave cylinder.
View 1 Replies
Advertisement
My 82 f150 4x4 302 c6 trans is acting up. My c6 is slow to shift into any gear when I shift the column shifter, after a moment it jerks into gear, also it doesn't seem D is doing anything but all the other gears seems to function manually or auto.
Fluid level looks ok, maybe a little high on the dipstick. I'm going to check the modulator and do a fluid/filter change but looking for a link to the band adjustment screw ?
View 3 Replies
I have a 2005 ford expedition with 91000 miles, it has the 5.4 w/ the 4r70w transmission.
For some reason when my truck tries to shift into 4th gear, the RPM's climb to approx. 3000 rpms (meanwhile the truck is not gaining speed) and slowly drops down to about 1000-1500. once the rpms drop down fourth gear eventually engages and I can go about my business as normal as long as I do not let my mph drop too low.
If I turn O/D off, the truck drives perfect, minus not having overdrive.
If I come to a dead stop and put the truck in 2nd gear, with O/D on the truck drives great and it has good engine braking so I am assuming that the band is holding.
I took it to a transmission shop to have some diagnostic checks done, they told me that fourth gear was barely engaging and that they would have to tear apart the transmission to diagnose it further, I told them not to disassemble the transmission.
So I changed out the torque converter (which I assumed was "fourth gear") and changed out all the fluid, the fluid looked a little burnt but there was no debris in the pan but there was some silver material on the tranny pan magnet, and installed a new filter. and the problem still exists.
View 7 Replies
I have a 07 f150 getting 17 mpg in town, I would like to get 20 MPG in town, this is a 5 speed, i do not shift into 5th gear. Max in town in 40 MPH. I have 3.55... I was wondering would 3.27 getting me to that 20 MPG?
View 14 Replies
My truck gear shift is stuck in Park (console type). I have been reading threads that discuss potential causes such as blown fuses, bad brake switch, bad brake shift interlock actuator, and even ignition switch. All fuses are okay. Before I try to get into all the other possibilities, I have a question around what the local auto parts worker suggested. He said that there is a small plastic piece that may have slipped down interfering with gear movement. This could make sense, especially since the white manual release lever doesn't seem to be moving.
View 14 Replies
Reverse band broke in my C4, I took it apart enough to get the rear band out and then reassembled. Everything to my knowledge was seated correctly and the front pump seated flush with the case when I reinstalled (which is supposedly a sign that it is all seated correctly). I adjusted the bands to spec and replaced the vacuum modulator and torque converter. These were the only things replaced besides the reverse/low band. Vac modulator was replaced to original (yellow band) as I was running an adjustable before. TC was replaced just because I did not the last time I had the trans rebuilt in 2003....decided to go ahead and R&R.
I got everything assembled, filled up with fluid and no leaks. I start it up and once i finished topping it off, the truck moves forward in every gear... including park! It also seems that I'm missing a shift detent. I have P, R, N, D, 2 but no 1. I disconnected the shift linkage and tried manually shifting from the trans and have the same issue.
I did not open up the valve body, just unbolted and replaced. When you start it up, it doesn't jump forward (while in park) but when you rev it up it sounds like the motor is under load. I've consulted my Haynes C4 book and an extensive google search and no way...
View 7 Replies
Ok so I went mudding this past week, and I put my 997 7.3 truck in 4x4 had fun then took it out of 4 wheel now it won't shift past 2nd gear top speed 35 mph.... It still has all the power revs up Rpms fine but it won't go faster then that.
View 8 Replies
I have a 98 Chevy truck with a 4L60E. It has no second gear. I was sitting in park for about 10 minutes with the engine running, then put it in drive and it never shifted into second. It felt like it went straight to 3rd. I played with it manually until I figured out I had reverse, 1st, 3rd, 4th and torque converter lockup, just no second gear. My acceleration rate was medium and when I reach about 27-28 mph it would shift from 1st into 3rd. It has 230K on it so I rebuilt it with all the typical parts - frictions, steels, band, sun shell etc., still no second. I then pulled the pan back off and replaced the spacer plate and put in a shift kit. While I had it down I put a corvette servo in and did an air check. It worked fine. I could feel the band tighten.
Both the 1-2 and 2-3 solenoids checked good at 23 ohms. I swapped their positions to see if it would make a difference. I also checked to make sure the 1-2 accumulator piston wasn't stuck in its bore, the spring was new from the shift kit. It was fine. Put it back together...still no second gear. When I originally pulled the pan off for the rebuild, the pan was free of any debris and was very clean. I then drove it a couple of miles to a local transmission shop. They put their scan tool on it and drove it around the block. There were no codes and the ECM was calling for second gear. It doesn't sound mechanical since almost all the parts have been replaced, rebuilt or inspected that affect the 1-2 shift. It sounds electrical. Is there anything I have missed?
View 14 Replies
i have a 1982 chevy 1500 4x4 with a 700R4 and it has never give me any problems at all has always shifted firm and smooth goes instantly in to drive and reverse. One day last week i got in and the truck will not shift in to second actually wont come out of first the reverse still works fine and the first is still fine it does not slip or hesitate at all. I pulled the gear cover off and can spin it!
View 8 Replies
97 Silverado - 5.7 with 4l60e trans. truck will not shift into 2nd gear while driving. stays in first gear until rpm are high and shifts into 3rd. under hard acceleration will stay in 1st until let off gas then shift into 3rd. manual shifting results in same, no 2nd gear until selector is moved into 3rd then shifts into 3rd. Haven't got any trans codes, fluid change netted no change in performance, fluid was pretty dirty but didn't smell burned, and there were no metal shavings in pan.
View 9 Replies
2 parts to this problem, Just changed the brakes/rotors, drums, shoes all around again, but still have this problem.
1. While stopping at a light when the truck slows down to 5mph or so the petal seems to go soft and the abs kicks in and the truck seems to carry on another 5-10ft further. It slows down from hwy speeds normally but just when it comes down almost a complete stop the abs will kick on in very fast pulse and keeps rolling for a few more ft. Even on dry surfaces.
2. Sometimes on slippery surfaces (gravel roads/rain/snow) it seems like the rear brakes lock at low speeds when coming to a stop.
Just thinking of disconnecting the abs sensors to all wheels......
View 1 Replies
Ok its a 96 explorer 4x4 and I just picked it up so I am learning all the things wrong as I go here. First off every now and then when the truck was almost to a stop the abs motor would kick in and make the abs noise. I checked the brakes and decided to change all 4 rotors and both sets of pads. I just push the fluid back up when I change pads instead of making a mess with bleeding and I am still getting the abs noise once in awhile. So could this be something wrong with the abs or should I sit there and bleed all 4? There is no lights on in the dash.
View 2 Replies
I need to solve tranny problem, it started out a while back, would not shift back into drive after stopping at stop sign (after driving fine for about 20 miles) thought maybe dirty filter so did fluid and filter change seemed to work for a while then started again noticed it was mostly after using cruise control, but u joints were very bad, so replaced 2 of the 3 and worked fine for about a thousand highway miles, then got really bad. Now when I check the tranny fluid cold and /or hot it is way up on the dipstick. Took to ford dealer in ladoga, lied and said no speed sensor codes, but list on the paper he gave me had all kinds of abs and a p500 code.
View 9 Replies
New issue I've discovered , when stopping , the RPM's drop down to 500, truck acts like it wants to stall , then goes up to 750 RPM's . Then it's fine . Doesn't hesitate when accelerating . Idles slightly rough after start up , about 30 seconds . I've checked the air filter , cleaned the IAC and MAF. Fuel filter is only a year old . What I should check next ?
View 14 Replies
Recently purchased 2006 F-550. Noticed the brakes seemed a bit squishy and weren't stopping the truck as well as I thought they might. Looked under the car and saw this at the right rear tire. Give it to me straight, doc.
View 14 Replies
My 85 300 cid with a C6 trans won't shift out of first. Seems like this happened several years ago and it was a vacuum diaphragm or something like that. Is this user fixable or do I need a transmission shop to look at it?
View 2 Replies
1990 F150 2wd, E40AOD tranny. Will not shift past 2nd. Reverse works. Does not have compression braking. Started when pulling a empty trailer up a hill on the interstate.
View 1 Replies
302 V8. Autolite 2150 carb. Auto-tranny. My vintage Ford truck which I love has developed a problem where it idles too fast for too long after warm-up. What I mean is that it is normal when it works correctly for it to idle fast for a few minutes until it warms up, at which point the idle speed slows down to normal. The way it works when it is working correctly, after a few minutes to warm up, I step on the gas pedal briefly, and the idle speed to kicks down. That's the way it is supposed to work. It seems actually like there are actually three idle speeds when it is working correctly. Fast, not quite as fast, and normal, all accessed via the kick down operation. Working correctly, it takes maybe three minutes to kick down the two steps to the normal idle speed. Does that sound right?
Anyway, the problem is that now it stays at the highest idle speed for 15 minutes. Eventually it kicks down to normal. But the high idle speed is too much for 15 minutes. Plus as it warms up the high idle speed becomes even higher since it doesn't kick down like it should. So it becomes difficult to keep the speed below 25 mph even w/out pressing on the gas pedal. It idles at about 25 mph for 15 minutes as it warms up!
I looked at my Chilton's manual -- better than nothing, but barely -- and it mentions something about a vacuum choke kickdown, a heat riser gadget, and the auto-choke. How to test each one to find what the problem is?
View 4 Replies
I have been having an issue with my 4-5 gear shift under hard acceleration and know that a rebuild is due soon but I was wondering if any high performance kit available with all the clutches and friction discs needed to rebuild.
View 6 Replies
I have a 1998 F150 with auto lock 4x4 and a automatic transmission. The problem I am having is after setting for about a week I drove it and 1st to second shift normally but when the RMP's/MPH hits time ti shift to third I get RMP increase and no third. I have shifted it manually 1 then 2 and into drive same result RMP's increase just like it is in neutral.
Miles on trans is about 120K have been serviced about 10K ago with no poor color or smell. Mechanic said transmission and filter looked good no metal or junk in oil. I drive down the road and it shifts from first into second then about 35-40 it hits what should be third but nothing free RPM's. I let it slow down to below 35-30 second kicks back in and away we go again until it's ready to shift into third.
I have been told possible speed sensor problem, possible other sensor problems looking for leads on where to look and what items to check. Just had Shop Mechanic drive it and he was baffled for everything looks good that he checked such as oil, and how it drove until it tries to shift into third. No over drive light flashing or anything and no engine codes showing at all everything clean in memory.
View 2 Replies
I recently bought my grandfather's old F-150, its a 1983 model with the 351w and the 7200VV carb. I replaced the distributor cap & rotor, plugs, wires, and fluids. The truck idles just fine in park/neutral, but when I shift it into reverse or drive, it stalls out. There is a valve of some kind attached to the carburetor, and it opens and closes rapidly as the truck dies (in time with its sputtering) so I think it may be the cause of the problem. I have not been able to find much info on that carburetor, but I think that valve is a fuel temperature system that meters the amount of fuel going to the carb depending on is temp. Can I replace that part without having to replace the whole carburetor?
View 10 Replies
