Ford - F250 :: 2000 - Noise And Leaks From Transmission
May 16, 2011
I own a 2000 Ford F250 4x4 equipped with the 5.4L and an auto trans that was purchased 2 yrs ago. Last summer we had some noise and leaks from the trans. Dealership fixed us with with a new pump and torque converter, fixed the problem. Now I have an issue where the truck will go into reverse, but will not go into any forward gears. Fuid level is fine, no signs or symptoms of overheating, no noises, or symptoms of something obvious. My son drives the truck and has stated that sometimes the park/safty switch gives him problems when trying to start the vehicle, he has to "wiggle" the shifter (or put in Nuetral) to get it to start. I'm thinking maybe the shifter/linkage may be loose or something, rather than a real transmission problem.
View 3 Replies
Advertisement
I am new to being an F250 owner. Just recently purchased a 2000 F250 SD 4x4 with the 5.4 and a 5 speed trans. Got a pretty good deal on it, because I knew some work had to be put into it, and do plan on dropping the trans. Currently, if the truck has been sitting for a little bit, not cool, but not running for a little bit, when I start it, whether it is in gear or in neutral, there is a noise coming from what seems to be the clutch area.
After a couple minutes of driving, this noise goes away and all sounds as it should. A little bit of researching turned up the possibility of the throw out bearing being bad, however, I found other posts online that doubt this. Another symptom that I assume is connected is that if I go to put it in reverse at 0mph from neutral, it grinds.
In order to go into reverse, I have to press in the clutch, put it in first, then put it in reverse, at which point it goes in no problem. I had already planned on replacing the clutch because it seems to me that would be the logical choice as to where the problem originates, so no issue there. But perhaps I'm wrong??
View 13 Replies
So last weekend I installed a transgo kit for my 4R100 transmission in my 2000 F250 diesel. I didn't really care about getting a shift kit, but I had problems with delayed shifts and figured the accumulator springs had broken. It turns out that was correct, the 2nd gear spring came out in 8 pieces.
Anyway, the transmission shifts great now, but when I put it in reverse it the engine jumps up 200 rpm and then it bogs down as it engages reverse forcefully. It also does this while selecting 1st from Park.
From what I'm reading it's the TC not unlocking and/or a fluid pressure/volume issue. I've also read the filter might have fallen off, I had a hell of a time keeping it in place. I've checked the the fluid level and everything is good there. My question is when I drop the pan, aside from the filter, what should I look for?
View 4 Replies
I was driving my 7.3 down the road and it started acting like the trans was slipping, it revved up and tried kicking down a couple times and when I slowed down and went to speed back up it just had no power coming through the trans to the wheels it just revved. I put it in neutral and it idled up for about 5 seconds. I put it in park n shut it down. I fired it back up after looking everything over and it moved about half mile down the road and no power to the wheels again. The trans is full of fluid, is there a sensor that could of went bad or just the torque converter or the entire thing shot? Only owned my truck 6 months has a trans and motor swap already from previous owner. 180k on current motor n Trans. 382k on my truck. t6 4" turbo back banks exhaust only mods I know of.
View 11 Replies
I have a new to me 2000 F250 7.3 diesel with automatic. Truck has 185K miles and tranny is starting to slip occasionally. Do these trucks come with a OEM tranny cooler or do I need to add or upgrade the OEM one. Someone also told that there is something called "bulletproofing" the tranny on these trucks. BTW, what would be a reasonable cost to have a two wheel drive auto tranny done on my truck?
View 7 Replies
I noticed an Oil leak of sorts on my truck( 2011 quad 4x4 f150 with ECO) when i did an oil change. Took it in and basically this is what i was told. Tranny was leaking from front seal and to to be removed for repair, upon further inspection the tech noticed the trans fluid appeared to be darker than normal. He tore it down and seen that the clutch plates and other components were excessively worn for a truck with only 15,000 miles. So any way the trans was about to have a catostrophic failure. Its getting replaced.
View 14 Replies
I have a 2003 f250 4x4 with a 5.4 motor the automatic trans is shot. I can get a replacement trans from 2000 f250 4x4 with the v10 motor. I tried my best to research it bell housing supposed to be the same so it should fit. But I'm not sure what they changed in those years internally or electronically.
View 2 Replies
I have a 2000 F250 4x4, it has been sitting in my garage for about 3 weeks. I cranked it up and backed it up about 10'. A few hours later I noticed a lot of transmission fluid on the floor. I remember hearing a hissing sound when I cut it off but didn't think anything about it. The fluid is on passengers side of truck, right side of the engine. Most of fluid is toward the rear but some ran down in front of the axle also. It's up high also, I've got fluid on rear of valve cover. I've cranked it up and let it run but can't get it to leak. Where did all this fluid come from?
View 5 Replies
01 F-150 7700 ed.
I have a 4R100 Tranny with 139K miles. It has been rebuilt. Ever since the rebuild (over 10 yrs ago), if I park the truck for a week or so or more, I will end up with a decent size puddle of trans fluid underneath the truck. I took it back to the shop that did the rebuild a couple times, but they could never find anything. It leaks enough to where my fluid level drops enough to cause the transmission to slip in a U-turn because the pickup tube becomes uncovered. I have a couple theories, but am wanting to hear from the collective.
Theory #1 When I park it on my slightly sloped driveway I don't regularly use the parking brake, so it rests on the gears, which eventually forces fluid out an overflow or breather tube.
Theory #2 (a very thin one) due to pressure changes associated with the weather, fluid is somehow siphoned out a breather tube due to some blockage internally in the tranny to where it's not equalizing with the outside air and has a high pressure within... ( i kinda laugh at myself for this one, but I am at a loss over the source of this)
View 14 Replies
I bought this truck with a stock automatic transmission and 260k miles back in October expecting the transmission to be the first thing to go. Recently I had a transmission code, OD OFF light flashing, for the bad speed sensor which i got replaced. Then the OD OFF light started flashing after some hard driving when I would put into neutral or park so I took it back to the mechanic, Hanahan Truck and Auto in Sc. They looked into it and there wasn't any different code in the system but they noticed when you lay into it driving it slips some between 2nd and 3rd gears so that could cause the computer to put in a code.
They said usually a rebuild runs from $2k-2.5k and they also recommended a Jasper reman for roughly $2.8k which comes with a 100k mile 3yr warranty. So I figure replacing the transmission is probably the way to go. Any recommendations for a replacement. I've heard ATS and Sun Coast are decent options that I could build one. I'm looking to stay close to $3k. My truck is a 2000 F250 lariat 4x4 with 268k miles. I'm installing an S&B intake, 4" MBRP exhaust, and DP-Tuner's F6 chip when I get the transmission work done.
View 11 Replies
I recently changed the rear diff fluid on my 1999 F250 Super Duty (180k) It was due plus I was getting some chattering when making turns from a stop. The Diff fluid had about 60k miles on it and seemed to be a little low even though I don't see any leaks. I paid to have it done last time so I can't say what kind of a job they did.
I used Motorcraft diff fluid and 8oz of friction modifier. Two weeks later and about 500 miles, today I noticed on two occasions when turning a moaning sound coming from the rear of the truck. Could this be a sign of too much friction modifier and the cluthes are slipping or is something else going on?
View 1 Replies
I swapped in a manual trans in my 79 f250 4x4 about a year ago. i had the trans gone through before i put it in. I installed a new luk clutch, resurfaced the flywheel, new throw out bearing, etc.
Ever since i installed it there was always a clunking noise in the trans. I drove it and didn't think much about it until recently where im just fed up with it. the trans always shifted nice and tight with no grinding.
In the past few weeks i picked up a parts truck for the trans thinking that's what my problem was. I drove the truck before i pulled it and it mad no noises whatsoever. I had it gone through and reasealed it before i installed it. I pulled my old trans and it still looked good with no slop on the input shaft(which i thought that was the problem). I installed the new one and once again same noise.
I decided to pull the trans again this time pulling the bellhousing and checking the clutch. It looked like new to me still and i saw nothing abnormal. Put it back together and still the same. I swapped the transfer case too, checked both driveshafts all is good. I am thinking its coming from the bellhousing(maybe the clutch is bad)
So here is a video and you can hear what I am talking about it happens mostly when I engage the clutch and i am coasting. it is much louder now with no carpet and the trans hump cover off.
Np 435 transmission clunk - YouTube
View 9 Replies
I'm a new Ford owner, when I engage 4wd I get a fairly annoying whinning / wheering sound that sound like the front end. Only makes sound under acceleration not coasting. No vibration at all.
View 11 Replies
My parents 2000 Explorer is having issues...It started with check engine light...came back to Oxygen sensors...Replaced all 4....light came back...still a couple of same codes...P1151 and P0153...smoked the intake with Evap Leak Detector...have several small vacuum leaks...little at EGR (No EGR codes)...little at TPS (No TPS Codes)...Little at throttle shafts...and some coming from what looks like underneath throttle body....none of these are as much of a concern as the next thing....NOW the trans will not shift out of 1st...unless you manually shift it from Drive to 2nd...then no other gears...Reverse works fine.....
View 13 Replies
I purchased my first truck 2 weeks ago private sale a 2001 Explorer Sport Trac 4v4 4.0L. I noticed it had small leaks coming from transmission and front differential gaskets (the diff is silicone) but the oil levels remain fine. Within days I heard a loud hum coming from the engine for 10 seconds then immediately after i was slowing down for a speed bump and my truck tried to stall and since that point it was riding very rough at low speed/idle and sometimes giving it gas seemed to just kill it. Next day a check engine light comes on and I get it checked It was Bank 1 running lean and B1155 (Output shaft speed signal) which concerned me from what I found it is located by the transmission oil filter which has the leak.
A few more days later I broke down on the side of the road, the alternator had died and killed the battery, I replaced the alternator and belt, replaced the 6 spark plugs, 3 of which i removed way to easily with my hands and all 6 had an incorrect gap. Initially the car was still rough but now with the new plugs it is drivable but still a little weird on startup and idle and a little bit of the shakes around 60-65mph and seems to be over actively shifting soon as i let off the gas even a little bit. Today I had the check engine light assessed again, now Bank 1 and Bank 2 are lean, still have the B1155 as well as a new C1676 (Battery pack voltage out of range) which light research said it could be ABS module or it could be a false code from being jumped days prior and that code wont clear on its own.
View 6 Replies
1999 F250 super duty w/ 5.4... My truck seems have issues keeping speed on the interstate like its not wanting to switch gears on time. Its auto by the way. Gotta little hesitation in the idle exhaust due that I have several leaks in my exhaust. Could that be the problem?
View 3 Replies
I just recently picked up a 87 F250 with a 6.9 and a ZF5 trans. The PO replaced the clutch, and mentioned that he replaced the clutch fork too
Since I bought the truck, I've had some nasty rattling noises. It rattles when in neutral, and stops when I put the clutch in. The noise also comes back on occasion when decelerating at highway speeds, in 2nd as soon as I stop accelerating, and at low speeds in 3rd.
What is causing this?
View 4 Replies
I own a 1971 Ford F-250 Custom with the 4 Speed Synchronized Warner T-18 transmission. When I put in the clutch, once it engages, it makes a very loud whirring noise. I'm not concerned about the noise as much as possible issues with the transmission itself.
View 1 Replies
I cant replicate the sound when its in park so i did a very dangerous diagnosis having a friend stomp on the break in gear and rev the engine to exactly 2000rpm as i searched for the sound. The sound is coming from in front of the transmission. I had removed the inspection cover as per another members fix for this sound and its still there. Could it be the torque converter touching something after it flexes at that speed?.
View 14 Replies
I recently changed the clutch in my 1967 F 250, all was golden. This was about 5 months ago , just the other day when going from 2nd to 3rd gear there is a clang and popping feel. the truck was making similar noises before the clutch blew out causing me to change it last time.
View 1 Replies
2001 F250 7.3L 280k miles. Truck is new to me in the last 6 weeks. Was driving out to Glenwood Springs last night and I got a weird rear end vibration between 79 and 81 mph - couldn't say if it's a new vibration as haven't had the truck long enough. It's sort of still there over 81 but less obvious than bang on 80. Whilst the vibration was there I caught a slight dip in the road that caused a grinding noise to accompany the vibration - I'm guessing because something's was getting extra loading on the upside of the dip.
I'm away from home until Monday so my options are a bit limited, however while crawling around in the dark last night pushing and shoving stuff to see if anything was loose I noticed a couple of things:
Minor leak from pinion seal - but it has flung some spots of oil. Drive shaft 'center bearing'(? U shaped attachment on drive shaft to chassis with rubber bearing?) has play I can push the drive shaft at least a 1/4" with my hand and it seems a little sloppy but I'm no mechanic.
I'm going to check transmission fluid level today and top up if required and check the magnets, such that I can limp home as necessary avoiding 80 and get the diff checked and pinion seal replaced. Does the drive shaft bearing need changing or should it have that much play? I'm assuming it's LSD on the rear?
View 14 Replies
