Ford Ranger / B-Series :: 1996 4x4 Manual Trans Missing 3rd Gear
Feb 17, 2015
1996 4x4, manual trans. Wants to kick out of first, and when shifting into 3rd I have no gear. Doesnt grind, just goes in as though it were neutral.
View 4 Replies
Feb 17, 2015
Advertisement
Ford Ranger / B-Series :: 1993 Manual Trans / Hard To Shift Into First
I'm having a little issue with shifting into first. Once in a while it simply will not go in, like you're pushing the shifter against a brick wall. If I turn off the truck and turn it back on, it works absolutely fine. I can shift into 2nd-5th no problem at all times. Is it just the shift linkage, or...? I'm not really sure where to start.
View 7 RepliesFord Ranger / B-Series :: 1996 - Engine Missing And Battery Gauge Fluctuation
I have a 96' ranger that has been missing quite regularly. The vehicle has over 200,000 miles on it, but has been taken care of regularly by me since 75,000.
Problem: When I start the vehicle, the engine takes a little bit to find the idle. It spits and fumbles around some until it finds a somewhat rough idle. Often, when I first start driving in the morning, the vehicle really jumps around due to misfiring. Even after running smoothly for awhile, the vehicle with sporadically misfire with no rhyme or reason. This is particularly true when climbing a grade. When sitting at a red light and idleing in gear, you can definitely feel the truck shaking from side to side. Also, when idling in gear, the battery gauge on the dash fluctuates, but when the vehicle is in park the battery gauge doesn't fluctuate...it just idles a little rough.
I had the Ranger to a garage and had them check the battery and alternator connections and ground to try and figure out what is making the battery gauge fluctuate...alternator and battery checked out...no diagnosis for fluctuation.
I replaced all plugs and wires and also checked the coil pack. One of the coils (#6) had some build-up in the top. I cleaned it out and replaced all the plug wires and everything snapped in place and fit fine.
The garage did tell me that an error code came up with the EGR valve and or sensor. They didn't seem to concerned about it. Do the EGR valve could be the cause of all the stuttering and misfiring going on with the ranger? I really don't know where else to look. Maybe replace the coil pack?
Ford Ranger / B-Series :: 1999 - Trans Won't Shift Into Any Gear
i have a 1999 mazda troy lee b3000. The truck has a 3.0 flex fuel and 4r44e and when you go to drive it. turn the key engine fires up but the trans won't shift into gear. Here is the back story.Bought the truck brand new in 99 I'm the original owner it was a daily driver up until 2 years ago. the truck has over 300k miles and still ran great but the camshaft was starting to go. I was gona replace the cam but came across a killer deal on a new engine. picked up another 3.0 flex fuel with 50k miles. drove the truck into my garage removed the old engine installed the new engine. got in the truck turned the key and the new engine roared to life.
I went to put the truck into gear so i could get it out of the garage and go for a test drive and nothing. went to put it in drive and again nothing. no matter what gear its put in it doesn't move at this point i was confused and decided to quit for the night. That was in 2011 its now 2013 the truck has just sat there sense then. I've tried anything and everything even went as far as swapping transmissions and computers with no luck. I took the trans apart I don't know how many times can't find anything wrong with it.
Ford Ranger / B-Series :: Trans Sometimes Takes A While To Go Into Gear When Put It Into Drive
I have a 98 XLT 4.0, auto trans with 109K miles and when it's really hot outside and it's been driven when I start back up and put it into drive it sometimes takes a while to go into gear. A friend says the transmission fluid doesn't look too good and it smells. Obviously I have a transmission problem but my question is would changing the fluid do any good at all? Since the tranny is bad what harm could it do? The fluid was never changed previously.
View 6 RepliesFord Ranger / B-Series :: 1999 - Trans Slipping In 1st And 2nd Gear?
I have a 99 Ranger 3.0L automatic, ext cab, 2 wheel drive. Door sticker show code "T" which I looked up as the 4R44E. The trans seems to be slipping in 1st and 2nd. Thought it was "reared shudder", from a "limited slip" differential but mine is not limited slip. just the regular 8.8 with 373 gears.
Wanting to know what if any options I have for buying a new / rebuilt tranny? I've seen where depending upon the year and motor, Ranger can have 4r44e, 4r55e, 5r55e, etc.
Ford Ranger / B-Series :: Hard To Get Into Gear - Trans Partially Engaging
I have a 99 ranger 4x4 4.0 V6 with 200K miles..I just had the slave cylinder replaced and bled however, it is still hard to get into gear and when at a stop light with the clutch pedal pushed in all the way the truck tries to move forward as if its in gear. I took it back to the shop and the mechanic says that the hydraulic system is working as it should and the problem could only be the pilot bushing failing and causing the trans to partially engage. The clutch and previous slave cyl only had 25K before the slave cyl failed and started leaking!!
View 12 RepliesBmw :: 1985 - Manual Trans Will Not Shift Into 1st, 3rd Or 5th Gear
My 1985 BMW 635, standard transmission suddenly developed shifting problem. It will not shift into 1st, 3rd or 5th gear. It will shift into reverse,2nd and 4th gear. The car is not driven on any frequent schedule, infrequently. I can't remember the last time the transmission oil was changed.There has not been any mechanical distress,grinding of gears,etc. you just cant engage those gears. They all are moving the shifter from neutral to a up position. Is it possible that sludge could be blocking the movement of the synchronize r?
View 2 RepliesFord Ranger / B-Series :: Missing When Started And CEL Came On
I have a 98 Ranger with a 3.0 (5 speed) that has 254,000 miles on it. I drove it to town this morning (8 miles) and it ran normally. I stopped for just a few minutes at a house and when I re-started the truck, it was missing very bad and the CEL came on. It wouldn't haul itself in anything higher than 3rd gear. I decided to try to make it back home. I drove it less than two miles and it cleared up and started running perfect again. I came home anyway and read the code with my scan tool.
It said that I had a miss fire on cylinder #5. I erased the codes and shut the CEL out and its been running perfectly ever since. (I have put about 150 miles on it so far) If it does it again, I will start by replacing the plug wires. I have already done that but its been a long time ago. The plugs have been replaced twice as well. I was wondering if it could be something other than electrical like a dirty injector or maybe the compression rings lined up and it momentarily lost compression.
Accent LC (2000-05) :: Manual Trans Notches Sometimes When Shift Into 2nd And 3rd Gear
I just got a 2000 accent. The problems is that sometimes when I shift into 2nd and 3rd is notches sometimes. But it does not do it when i shift down. Also if I shift fast it will occur less often as when I shift low. When my friend drove the car it didnt do it for him. So maybe it is how i drive or something. I make sure the clutch is down all the way.
View 7 RepliesFord Ranger / B-Series :: 1998 4.0L Manual Won't Shift As Soon As Start The Engine
I'm 1200 miles from home living in a hotel right now. Was on my way to the store this morning and I took it out of gear. When to put it back in, and it wouldn't go in. Fortunately, I was still moving, so I coasted off into a parking lot. Once I shut the engine off, it went right into gear. It moves freely through them all. As soon as I start the engine, it won't shift. It is not my clutch. I can start the engine with it in gear and the clutch in, and it won't creep at all (was sitting on level ground when I tried). At least this means I can get it places if I slip the clutch a lot. Took the inspection cover off, and all looks well in there. It hasn't been acting strange. It shifted just fine right up until this. No strange noises either until now.
Now there is a slight squeaking sound if I try to force it into gear with our without the clutch pushed in. Since I've never let a mechanic touch my baby before, and I have to now, what possible things should I be looking for to make sure they are honest? I'm thinking maybe I killed my pilot bearing? Second, while its apart, I'm going to have them replace the clutch and slave cylinder since its got 160K on it and as far as I know, the previous owners never did that. Recommendations on what clutch to get? Its been towing some lately. I don't know if that makes a difference.
Ford Ranger / B-Series :: Removing Manual Door Lock Cylinder
I recently bought a 1994 Ford Ranger, XLT 4 cylinder supercab. They lost the door keys when they replaced the ignition because they never locked their doors. I bought new lock cylinders with keys and set out for an adventure. Removing the metal clamp that holds the cylinder in place was actually easier than I thought. It's that darn plastic piece connecting the cylinder to the rod for the lock system that will not break or come off. Here's the best picture I could find real quick. How do you get that vile piece of 20 year old plastic off? It's in a difficult place to get tools in there, and I can't seem to get leverage with a small screwdriver anywhere. What tips and tricks do y'all have?
View 1 RepliesFord Ranger / B-Series :: 2010 - Grinding Noise From Manual Transmission
A friend has a 2010 ranger with the 2.3L with the manual transmission. He said that when he drives and the rpms are up he said he gets a grinding noise it doesn't matter what gear 1rst or 5th. He think throw out bearing but no noises at all until the rpms are up there. I was think internal like shift fork but don't know.
View 4 RepliesFord Ranger / B-Series :: 2001 2.3 - Missing When Accelerating?
I have a 2001 ranger 2wd with a 2.3. It has a miss when acceleration. There is no check engine light. I have changed: fuel filter. Plugs, wires, crank position. Sensor, cleaned mass air flow sensor. Ran 2 bottles of injector cleaner in it. Still missing???? It runs and idles great. Just has a miss in the lower RPM's 1000-2000 then goes away. I really don't wanna take it to a shop. What do you all think??
View 11 RepliesGolf IV / Jetta IV :: Noisy Manual Trans In Reverse / Whining In 1st And 2nd Gear
I have an 04 Jetta 1.8T that I recently acquired and have a problem with a noisy manual tranny. Reverse is a bit noisy (more than usual) and when I get on it in 1st and 2nd gear it sounds like an awful whining noise. I have been told it could be either a bad throw out bearing or input bearing? BTW this thing shift perfect, like butter, no grinding at all.
View 4 RepliesFord Ranger / B-Series :: 1991 4WD Manual Tranny Locks Up After Going Forward A Few Feet
My 4x4 4WD Ranger has a 5 speed manual tranny that locks up after going forward a few feet. It can back up all day long but locks up going forward. some god awful noises (grinding, clunking, etc) come out of that gearbox. the 4wd is electrically operated. the ? is , can this tranny be rebuilt with a kit? I'm having great difficulty finding a replacement. Are bronco II's compatible? Engine is 2.9L V6. On disassembly I found 2 meshing gears with broken teeth.
View 5 RepliesFord Ranger / B-Series :: 1985 - Missing At High Acceleration?
85 ranger 2.3 fuel injected misses at high acceleration. Fairly new plugs and wires, just replaced the timing belt, pretty new fuel pump in tank, new fuel pressure regulator and pcv. It idles well, starts up and drives pretty well until you get it in 4th and really bog it down. Could be timing issues but I'm pretty sure I did everything right when I put the belt in. What it could be? I know when the tank fuel pump went out, it did something similar for a while...
View 9 RepliesFord Ranger / B-Series :: 1988 - Missing / Stumbling Especially At About 55 MPH While In Overdrive
I've got a 1988 2wd Ranger with a 2.9l v6. I just recently got it running. It has been setting for awhile. I replaced fuel tank, both pumps, fuel filter, Plugs, Wires, Cap, Rotor, TPS. It ran great for about 100 miles. Then yesterday on my way to work about 4 miles down the road it started to miss/stumble especially at about 55mph while in overdrive. When I got home I pulled the codes and I got KOEO 22 Map sensor signal out of voltage(engine off), 53 TPS signal voltage to high, 95 Thermactor Air System Problem, or Fuel Pump Monitor signal, indicates circuit problem.
KOER I got 21 ECT sensor signal voltage out of range or loss of signal during normal operation or Crank Sensor problem, doesn't have a crank sensor I believe. But I did change the ECT sensor and it still stumbles and seems like it misses. Noticed it is sluggish getting up to speed kinda surges and bogs. Im at a loss it isn't showing any more codes. Checked all plug wire connections and made sure everything was making connection. The only other thing I can think of is that the ignition module on back of distributor is going bad. Not advancing the time correctly.
Ford Ranger / B-Series :: Fuse Box Panel Cover Missing
I've a 1994 Ranger XLT 4.0L with a missing fuse panel cover. I'm trying to get the horn to work and we've traced the problem to a missing fuse. Unfortunately, there are 3 empty fuse slots and no info on their rating or use. Where I can get the proper info. Truck was a salvage, no ops manuals, and sloppy work putting it together.
View 14 RepliesFord Ranger / B-Series :: Missing On Light Throttle / Cruise
4.0. I'm having what feels Like a Miss on Light throttle/cruise. Once warmed up it's fine. Idle is fine too. There is No CEL/Codes.
View 14 RepliesFord Ranger / B-Series :: 1999 - Running Rough / Missing And Surging At 50 To 70?
I live in Kansas and was home in Georgia for the last 2 weeks. The truck drove great there after a fuel up started missing and surging at 50 to 70 thought it might have been bad fuel. waited till it was low added Lucas fuel treatment and premium gas still was doing it. no check engine light. went to Advance and fuse for light was blown they checked and was getting mass air flow code. unplugged it and seemed to be better, not perfect but better. plugged it back in and went to do it again. Changed mass air flow night before the drive back to Kansas. Ran well from Savannah to north Georgia then started doing it again the rest of the way home. Going to have advance check code again.
View 12 Replies