Ford Ranger / B-Series :: Trans Sometimes Takes A While To Go Into Gear When Put It Into Drive
Jul 1, 2012
I have a 98 XLT 4.0, auto trans with 109K miles and when it's really hot outside and it's been driven when I start back up and put it into drive it sometimes takes a while to go into gear. A friend says the transmission fluid doesn't look too good and it smells. Obviously I have a transmission problem but my question is would changing the fluid do any good at all? Since the tranny is bad what harm could it do? The fluid was never changed previously.
View 6 Replies
Advertisement
Daughter driving truck truck quits moving, I get there no drive and no reverse, has low and 2nd manually.
drive truck home, flush trans and cooler, road test all ok. this was 3 weeks ago.
This morning did it to here again, no drive and no reverse, she drove it home using manual low and 2nd.
I get in and when put into drive it feels like it tries but doesn't go all in, same with reverse. pulled it into low and vola I now have drive and reverse again
I'm thinking a we may have a bad or going bad shift solenoid. What I need to know is, is any of the solenoid valves on when in reverse are they the same as when in drive?
View 3 Replies
i have a 1999 mazda troy lee b3000. The truck has a 3.0 flex fuel and 4r44e and when you go to drive it. turn the key engine fires up but the trans won't shift into gear. Here is the back story.Bought the truck brand new in 99 I'm the original owner it was a daily driver up until 2 years ago. the truck has over 300k miles and still ran great but the camshaft was starting to go. I was gona replace the cam but came across a killer deal on a new engine. picked up another 3.0 flex fuel with 50k miles. drove the truck into my garage removed the old engine installed the new engine. got in the truck turned the key and the new engine roared to life.
I went to put the truck into gear so i could get it out of the garage and go for a test drive and nothing. went to put it in drive and again nothing. no matter what gear its put in it doesn't move at this point i was confused and decided to quit for the night. That was in 2011 its now 2013 the truck has just sat there sense then. I've tried anything and everything even went as far as swapping transmissions and computers with no luck. I took the trans apart I don't know how many times can't find anything wrong with it.
View 4 Replies
I have a 99 Ranger 3.0L automatic, ext cab, 2 wheel drive. Door sticker show code "T" which I looked up as the 4R44E. The trans seems to be slipping in 1st and 2nd. Thought it was "reared shudder", from a "limited slip" differential but mine is not limited slip. just the regular 8.8 with 373 gears.
Wanting to know what if any options I have for buying a new / rebuilt tranny? I've seen where depending upon the year and motor, Ranger can have 4r44e, 4r55e, 5r55e, etc.
View 3 Replies
I have a 99 ranger 4x4 4.0 V6 with 200K miles..I just had the slave cylinder replaced and bled however, it is still hard to get into gear and when at a stop light with the clutch pedal pushed in all the way the truck tries to move forward as if its in gear. I took it back to the shop and the mechanic says that the hydraulic system is working as it should and the problem could only be the pilot bushing failing and causing the trans to partially engage. The clutch and previous slave cyl only had 25K before the slave cyl failed and started leaking!!
View 12 Replies
1996 4x4, manual trans. Wants to kick out of first, and when shifting into 3rd I have no gear. Doesnt grind, just goes in as though it were neutral.
View 4 Replies
My gf's dad said I could have his 07 Ranger 4.0 2wd with 230K on the clock if I fix the tranny 5R55E. One day he was driving home and all of a sudden had no drive. The tranny will run thru drive, neutral and reverse, but has no drive to it. Engine revs with nothing to show.
Tranny fluid was very dark and pan had nothing but the usual "metal flour" in it. I stopped there, did not pull the filter or anything else.
View 3 Replies
I have a 98 Ranger, 4.0 automatic 4x4...I just replaced the upper and lower intake gaskets and after fumbling with the pug wires to finally get them in the right order, I suddenly find my OD light flashing off and on, and the tranny slamming into second, and once in top gear can feel the OD popping in and out? From my reading here it looks like a pretty common problem, but the solution isn't as clear...
The vehicle set for about 3 months while I healed up from a injury, and and was working just fine when I parked it...due to the blown lower intake gasket. I am thinking I have a vacuum line not connected or wrongly connected...or some kind of over looked item, but I can't spot anything...should I get a code reader and go from there...
View 14 Replies
The problem I have is the truck won't move in o/d. If I put it in revers 1,and 2 it works. A little back ground. 4 years ago the trans went out of my 95 4.0 4x4, had it rebuilt so it has 0 miles on it. It got really cold that winter had lots of trouble getting the trans and torque converter lined up. motor went bad on me. A few months ago finally had some money to spend bought a 98 explorer sport with a 4.0 x code motor. the motor runs fine apart from an oil leak and an exhaust leak. the exhaust leak is no big deal I just haven't gotten the system tight yet.
View 8 Replies
02 ranger 4.0 v6 auto has 110000 miles on it. at highway speeds 65-70mph feels like it strugles to shift, truck will shake and bounce some. when this happens rpm's jump from about 2200 to 3000-3200 after a little bouncing rpms drop to normal. issue seems to be the worst going up hill but will happen every time i hit 65-70. Also the truck will not bounce or shake with the OD turned off and seems to run fine this way.
tranny fluid/ filter just replaced with no change. new plugs and wires
View 3 Replies
I'm having a little issue with shifting into first. Once in a while it simply will not go in, like you're pushing the shifter against a brick wall. If I turn off the truck and turn it back on, it works absolutely fine. I can shift into 2nd-5th no problem at all times. Is it just the shift linkage, or...? I'm not really sure where to start.
View 7 Replies
2001 4.0 4x4 auto trans... Problem, tranny judders when coming to a stop moving at around 3-4mph. Engine drops to around 500rpm and maybe one second later returns to normal as the tranny seems to disengage. No judder or shifting problem when accelerating.
View 5 Replies
I have A 1986 ranger with a 2.9 v6. I am thinking of doing a diesel swap and I am wondering what engine and trans combos would work best for this. I was thinking 4bt but there are may other options that could work.
View 14 Replies
I bought a 2000 Ranger 4x4 3.0L auto today from the neighbor guy sight unseen with a "bad tranny" for $400. I'm very unfamiliar with the Ranger family, but long story short:
When moving the shift lever, the trans doesn't engage. It needs to be engaged from underneath. Do the cables tend to stretch, or break? I can't find any adjustment on it anywhere.
View 5 Replies
1990 Ranger 5 speed... The tranny has recently started making noises, first I thought it was the throw out bearing but I am afraid it is more than that. As I go thru the gears the trans makes rattling/grinding sounds: in 1st, 2nd, 3rd and 5th it is loud but 4th it is quiet. What might be going on inside the tranny....
View 14 Replies
I noticed a strange vibration in the 83 Ranger I own, it has the 2.3 and a 4 speed. When getting up to speed around 35MPH it would start vibrating, and the speedometer needle would bounce around and read slower than it was actually moving. This would start in 3rd gear, and continue thru 4th unless I let off the gas while it was in gear, then it stopped and worked normally. I put a grease seal in the tail section when I first got the truck, and when I pulled the driveshaft again today the seal was mangled and bent, plus there are metal particles around the main shaft where the seal goes. I figure the tail shaft bearing is shot, and I also found damage to the yolk with the U-joint, the shaft has a worn spot about 1/3rd the way around.
View 2 Replies
1991 2.3L 5 speed .... Okay here's my list of issues.... At idle will stall out, its almost as if i shut the key off, or sometimes taking off it'll sputter and stall, fuel filter has been changed. Back part of the tranny housing leaks, is there a gasket for that?
View 3 Replies
I bought a 96 Ford Ranger XLT Supercab 4.0 on the 21st and the gear shifter doesn't go into 1st gear but changes to the other ones(see pic below) and was wondering if it's a easy fix.
Also I have a oil drip(at least it looks like oil to me) and I can't figure out where it's coming from because it's a small drip and the oil dipstick and tranny dipstick both show full and I can't figure out where the drip is coming from and I only noticed a dip on a metallic tank but don't know what that is either but check out the pic below to see the drip I circled.
View 3 Replies
I have a 2008 F-150. When moving gear selector from park to either reverse or drive, trans has a delay engaging. After engagement, it runs fine, shifts ok, downshifts ok....
View 7 Replies
I purchased a 1990 Ranger 4x4 with a v6 from auction. Took it to local shop to have them check it for me. Found out that it has a 3.0 in it and mechanic believes it is from a taurus. Truck actually runs extremely well. Has a few codes due to the ECM is for an automatic trans. Now the problem. I was on the highway-in 5th gear. Terrible noise the nothing. When I got it pulled over. The drive shaft was hanging from the rear end. It had been twisted like a straw. The transmission side had the yoke only, and the tail housing was cracked. It rolls and the drive shaft at the rear end turns. I figured the trans locked up. I don't know what trans to look for---is a 90 2.9 5 speed the same on a 3.0 ??
View 6 Replies
I have a 97 ranger 2wd 4.0 with 5R55E. Drives fine in 1st and second. Slips in drive and rev.
View 6 Replies
