Ford Ranger / B-Series :: 1983 - Vibrates Around 35 MPH - Shaft Bearing Broke - Replace Trans?
Jan 25, 2013
I noticed a strange vibration in the 83 Ranger I own, it has the 2.3 and a 4 speed. When getting up to speed around 35MPH it would start vibrating, and the speedometer needle would bounce around and read slower than it was actually moving. This would start in 3rd gear, and continue thru 4th unless I let off the gas while it was in gear, then it stopped and worked normally. I put a grease seal in the tail section when I first got the truck, and when I pulled the driveshaft again today the seal was mangled and bent, plus there are metal particles around the main shaft where the seal goes. I figure the tail shaft bearing is shot, and I also found damage to the yolk with the U-joint, the shaft has a worn spot about 1/3rd the way around.
View 2 Replies
Advertisement
I am driving a 95 ranger xlt extended cab with a 3.0 two wheel drive with an automatic transmission. the two piece drive shaft with the carrier bearing went bad at the bearing. i separate the u-joint just after the bearing and was going to remove the nut holding the bearing housing together but cannot get the nut off. now i'm also finding out that i need a bearing puller to remove the damaged bearing from the 1st drive shaft.
Its turning into something i may not be able to finish. i saw on line an idea where a guy replaced the 2 piece shaft with a one piece. he states that a 1 piece drive shaft, 1998 or newer would work and no need for this bearing. you have to remove the cross member. it sound easier than what i'm trying to do. i looked at some old posts and galleries but did not see an article. here is a link to his website: How-To: Swapping a 2-Piece Drive Shaft for a 1-Piece in a 1983-1997 Ford Ranger
View 7 Replies
On my 04 150 auto, the clip that holds the shift cable to the trans selector shaft broke, Ford says i need to buy the whole cable and what did you do?
View 2 Replies
Truck has no spark except when you first turn key on it sparks or right when you let off from cranking it will give one spark. You can be cranking it and nothing and when you let off it kinda acts like it wants to start for a millisecond.
View 11 Replies
I have a 1983 ranger with a YFA. I recently took it apart and in the process of the rebuild I noticed the metal gasket was still in the spot where the needle pin goes. It has adhered to the carb. Any way to get it un-stuck? Also, there is a module, and the gasket comes in the rebuild kit so I know it belongs, the part number begins with 2I3 but the rest came off with the dirt. What is it for and would it hurt anything if it wasn't plugged in? It hasn't been since I bought it.
View 2 Replies
I recently bought a 1983 Ford Ranger Diesel pickup truck (2.2L Mazda engine, manual transmission). The dealer said to expect a little above 30 mpg on fuel mileage but the two fill-ups I've done show an average fuel mileage of 22 mpg. About half of these are highway miles.
I thought diesels are supposed to have good mileage. Is this typical for my year and model truck? Is there any way to increase the mileage? I just replaced the air and fuel filters and also changed the oil and oil filters.
View 9 Replies
My 1983 Ranger is in the shop. I'm being told that I need to replace the shifter assembly. I understand that this is a Mazda part, from a TK5 transmission. These parts are interchangable between bronco ii's of the same era.
View 1 Replies
I have a 2007 ranger and when applying the brakes i get a vibration, I think it may be in the rear of the truck but it is hard to tell.
View 2 Replies
I purchased a 1990 Ranger 4x4 with a v6 from auction. Took it to local shop to have them check it for me. Found out that it has a 3.0 in it and mechanic believes it is from a taurus. Truck actually runs extremely well. Has a few codes due to the ECM is for an automatic trans. Now the problem. I was on the highway-in 5th gear. Terrible noise the nothing. When I got it pulled over. The drive shaft was hanging from the rear end. It had been twisted like a straw. The transmission side had the yoke only, and the tail housing was cracked. It rolls and the drive shaft at the rear end turns. I figured the trans locked up. I don't know what trans to look for---is a 90 2.9 5 speed the same on a 3.0 ??
View 6 Replies
Checked icm and is good, replaced coil and still no spark. Issues be gan when about 700 miles ago rotor button broke while driving??? Replaced button cap wires and plugs. Engine fired right up. Ran 700 miles and rotor button broke for 2nd time. This time replaced and will turn over but not crank. That's when I checked icm and changed coil. what should i check now?? 1993 Ranger 3.0 ... Truck has 199,800 miles. Top end was redone at 140,000.
View 10 Replies
I replaced the seal the other day on my ranger because I noticed my fluid disappearing. Went ahead and changed the filter and fluid as well. Flushed the system, and I go back to my truck tonight and there's a huge puddle of trans fluid. And the output shaft seal is once again, up against the drive shaft. I've spent like $150 on trans fluid since Friday, and $1000+ to get the truck running again last month, so pardon me if I get edgy about her.
99 2.5 auto. I changed the trans pan gasket too. No leaks from it.
View 14 Replies
In 4 x4 ( 2000 ford ranger 4.0 ) and drive for a while I can smell gear oil burning off the exhaust looks like it's coming out of the right cv shaft? Is there a seal that goes first That's bad?
View 6 Replies
So my ranger was having a textbook wheel-bearing noise at around 50mph....when I turned to the right the noise went away implicating a passenger side wheel bearing.
So I replaced both of the hub bearings on the pass side and noticed that the front axle shaft u-joint right behind the spindle was really bad and was going to change it but couldn't get the spindle off so I said screw it.
Took it for a drive and the noise is still there. Could a worn u-joint possible replicate a wheel bearing noise? I am used to them making a clicking/popping noise while turning when they're bad, but not a whirring sound.
1993 ranger 4x4 manual locking hubs.
View 4 Replies
I bought a set of Ranger seats for my 1957 Ford project. My question is the drivers side seat reclining mechanism is broke. I believe the seats are out of an STX or sport model, they have a slide out bolster and power lumbar and side bolsters.
Where to get a replacement mechanism. The mechanism works the handle is busted off. It is from an extra cab so the handle is a two way for the driver and or if anyone in the back wanted to use it. I think they may be from a 1992, only say this because I had one backin the day with these kind of seats.
View 4 Replies
I'm replacing my clutch components in my 89 Ranger with an M5OD transmission. While I'm doing it I'm going to replace the input shaft seal on the transmission. I'm looking for the torque specs for the housing that holds the seal.
Also, should there be any play on the input shaft? My transmission has never made any noise but I noticed some slight play in the shaft.
View 1 Replies
I spent the day with a buddy working on his 91 ranger 4 cylinder 2WD truck because the clutch master cylinder shaft that connects to the pedal bent. We took the old part out and replaced it, but now we are having problems with the little pin that holds the line from the slave cylinder to the master cylinder in place. For some reason, even though the line is securely in position and wont budge with the pin in, it still leaks so we are unable to bleed the clutch.
I have looked all around the internet, including this site and wasn't able to come up with any explanation as to why the line is leaking, perhaps it is because the line isn't pushed in far enough, but like I said, it is securely in place and I wasn't able to push it in farther before forcing the pin into place. My buddy and I spent about 9 hours working on his truck today, including probably 3 or 4 just on trying to stop the leak.
View 4 Replies
I just bought a 5speed manual 2004 ford ranger 4x4 and when shifting usually upshiffter 1-2-3 I get a mi8ld clunk when I looked underneath I grabbed and can move the from drive shaft clockwise about 1/4 inch is this normal and if not how do I fix this?
View 3 Replies
This morning the passenger side wiper on my 89 Ranger stopped working. I heard a clunk noise and it stopped but driver side still works. What should I check first? I'm guessing a shaft came off but don't know where it is located.
View 14 Replies
93 Ranger, 4.0 liter, 4WD.....
Putting in a new clutch and clutch release bearing, and am wondering if I need to put the retaining ring in that came with the new clutch release bearing? When I took off the old release bearing, a ring did come off from somewhere, but I did not see where it was because it was so dirty.
The reason I ask is because my Haynes manual did not even mention a ring, so I was surprised to see one come off. And my manual does not say to reinstall the ring when installing the release bearing. I did get a newer Haynes manual at the library and looked through a bunch of Chilton, etc manuals.
The newer Haynes manual says to remove the retaining ring on 97 and newer models, but says nothing about putting it back in when reinstalling. So, I am not certain if I need to put a new retaining ring in with the new release bearing.
View 7 Replies
I have a 1987 Ford Ranger 2.3L, it's the truck I learned to drive in (stick at 13yo) and the 1st car I crashed too... So now this baby is almost 30 years old and recently had a minor restoration...
Engine was pulled out and all gaskets were changed, spark plugs, wire... All that stuff... It has been running pretty good, however last week a water line broke on the Left side near the spark plugs (if you are looking at the truck)
Since then It has absolutely Zero power. The slightest hill and even when pedal to the floor will lose power. Yesterday went from the start of a hill at 60mph in 4th to 20mph in 2nd because it didn't have the guts to go 1/3 mile uphill... I checked everything I could, and my brother took it to the exhaust guy who made a small hole on the Catalytic Converter and said it was good, but he could tell it was running too rich...
I replaced some of the vacuum lines last night, I found a lose one on the fuel pressure regulator (I think that's what it is, Its towards the engine firewall on top).
Idles beautifully, drives great, no rough shifting, pinging or knocking, no misfires. So that's what has me stumped... Runs great but just no power... Also before water line broke it was running fine with power...
1987 Ford Ranger
2.3L FI
5sp manual, Rwd
View 11 Replies
Today I took the bed off of my 99 ranger. I was sitting on the cab looking down at the rear axle noticed the drive shaft was not entering the rear diff perfectly straight. As I looked further into it, I noticed the distance between the rear spring on the passenger side tire, is noticeably different. To visualize it, the wheel, at the bumper side of the axle, has a shorter distance between it and the leafs than the cab side. Not massive, but a few inches, and it's noticeable now that I can stand over it. I'm beginning to be very annoyed by this truck and it's previous owners, whom I take it , scammed my brother quite well with a $5k tag for a truck with so much not right with it. It's about to become my yard art for awhile.
View 8 Replies
