Ford Ranger / B-Series :: 1999 - Output Shaft Seal Won't Stay?
Aug 20, 2017
I replaced the seal the other day on my ranger because I noticed my fluid disappearing. Went ahead and changed the filter and fluid as well. Flushed the system, and I go back to my truck tonight and there's a huge puddle of trans fluid. And the output shaft seal is once again, up against the drive shaft. I've spent like $150 on trans fluid since Friday, and $1000+ to get the truck running again last month, so pardon me if I get edgy about her.
99 2.5 auto. I changed the trans pan gasket too. No leaks from it.
View 14 Replies
Advertisement
I'm trying to replace my transmission output shaft seal on my 2wd and I can't seem to get the seal removed. I couldn't find anything to rent from O'rielly's or Advance Autoparts that would work. It's in there really tight ....
View 10 Replies
I'm replacing my clutch components in my 89 Ranger with an M5OD transmission. While I'm doing it I'm going to replace the input shaft seal on the transmission. I'm looking for the torque specs for the housing that holds the seal.
Also, should there be any play on the input shaft? My transmission has never made any noise but I noticed some slight play in the shaft.
View 1 Replies
I installed a JDM 2ZZ-GE engine and 6 speed manual trans-axle into my 2000 Celica GT.
I have ran into a interesting problem. I replaced the output shaft seals and now whenever the car is in the air and the suspension is unloaded (the drive axle is pulled slightly from the trans) the drivers side seal leaks a bit of gear oil. The drive axle is snapped into place. Nothing leaks when the car is on the ground.
I did reuse the old drive axles, which had a lot of miles on them but still appeared good and useable. I have been told to replace the new seal because it may be damaged, but I am wondering if it may be that the drive axle end is worn.
I have seen this with harmonic balancers for engines. They even sell a replacement sleeve for harmonic balancers so you can re-use the old worn one.
View 6 Replies
2001 ranger with 4.0, alternator failed and new alternator is also not charging, showing very little output. i've installed 2 new ones with no fix. the regulator is in the alternator, correct? I'm stumped and not sure where to go with this.
View 14 Replies
I just changed transfer case fluid on my father's F-350 for the first time in 13 years. (over 230k). Removed fill plug first and fluid gushed out of the fill hole unexpectedly. Did not have catch pan ready, so made a mess. I thought it was just over filled form the factory, but too much was coming out to be simple overfill. Almost 2 qt came out of the fill plug.
Did some google search and found many Ford trucks have failed transmission output shaft seal and transmission fluid leaks out to transfer case, causing transfer case to overfill. I am yet to check transmission fluid level, but considering how much came out of it that probably is the case.
Now, how bad of the problem this really is? Will overfilled transfer case cause some serious problem? 4x4 is rarely used (once or twice a year in winter) on this truck and from what I understand transfer case doesn't really do anything in 2WD other than just passing output from transmission through.
There are no fluid leaking outside and repairing the seal would be a too much of work for me.
Also changed rear differential fluid for the first time and I was surprised how clean the fluid was. There were thin layer of black sticky residue (sludge?) covering everything, but the fluid itself looked clean and no visible metal shavings. I guess that is why Ford said it does not require change under normal condition.
View 10 Replies
what i have is the driver's side door on my 1999 ranger is hard to open, the door seal sticks to the door and makes it hard to open, i am afraid of breaking the door handle off, is there any thing to clean seal with to make it not stick? the seal is not sticky to touch neither is the door but when out in the sun for a while they stick together, mechanic told me to spray with wd40 that didn't
View 2 Replies
I purchased a 1990 Ranger 4x4 with a v6 from auction. Took it to local shop to have them check it for me. Found out that it has a 3.0 in it and mechanic believes it is from a taurus. Truck actually runs extremely well. Has a few codes due to the ECM is for an automatic trans. Now the problem. I was on the highway-in 5th gear. Terrible noise the nothing. When I got it pulled over. The drive shaft was hanging from the rear end. It had been twisted like a straw. The transmission side had the yoke only, and the tail housing was cracked. It rolls and the drive shaft at the rear end turns. I figured the trans locked up. I don't know what trans to look for---is a 90 2.9 5 speed the same on a 3.0 ??
View 6 Replies
In 4 x4 ( 2000 ford ranger 4.0 ) and drive for a while I can smell gear oil burning off the exhaust looks like it's coming out of the right cv shaft? Is there a seal that goes first That's bad?
View 6 Replies
I've got a 1990 ford ranger 4.0 auto trans front transmission seal went bad, I've got everything unbolted abs ready to come put but the trans won't come over top of the front cross member, what could be the problem on why it won't come out?
View 3 Replies
I am driving a 95 ranger xlt extended cab with a 3.0 two wheel drive with an automatic transmission. the two piece drive shaft with the carrier bearing went bad at the bearing. i separate the u-joint just after the bearing and was going to remove the nut holding the bearing housing together but cannot get the nut off. now i'm also finding out that i need a bearing puller to remove the damaged bearing from the 1st drive shaft.
Its turning into something i may not be able to finish. i saw on line an idea where a guy replaced the 2 piece shaft with a one piece. he states that a 1 piece drive shaft, 1998 or newer would work and no need for this bearing. you have to remove the cross member. it sound easier than what i'm trying to do. i looked at some old posts and galleries but did not see an article. here is a link to his website: How-To: Swapping a 2-Piece Drive Shaft for a 1-Piece in a 1983-1997 Ford Ranger
View 7 Replies
I spent the day with a buddy working on his 91 ranger 4 cylinder 2WD truck because the clutch master cylinder shaft that connects to the pedal bent. We took the old part out and replaced it, but now we are having problems with the little pin that holds the line from the slave cylinder to the master cylinder in place. For some reason, even though the line is securely in position and wont budge with the pin in, it still leaks so we are unable to bleed the clutch.
I have looked all around the internet, including this site and wasn't able to come up with any explanation as to why the line is leaking, perhaps it is because the line isn't pushed in far enough, but like I said, it is securely in place and I wasn't able to push it in farther before forcing the pin into place. My buddy and I spent about 9 hours working on his truck today, including probably 3 or 4 just on trying to stop the leak.
View 4 Replies
I just bought a 5speed manual 2004 ford ranger 4x4 and when shifting usually upshiffter 1-2-3 I get a mi8ld clunk when I looked underneath I grabbed and can move the from drive shaft clockwise about 1/4 inch is this normal and if not how do I fix this?
View 3 Replies
I just had trans rebuilt in my 98 4x4 4.0 ranger I thought while they had the trans out go ahead and replace rear seal. Got the truck back leaking bad carried it back they claim to have replaced it twice while they had it and guaranteed it was not leaking they say the leak is from the oil pan so I'm gonna pull the motor this week. Question is: can make an offset rear seal I still believe this is the problem. Which oil pan gasket to use.
View 4 Replies
2004 automatic 88,000 miles 2wd
When I bought the truck it had a very small oil leak that would drip out of the bell housing between the housing and the inspection pan. it would leave a quarter (25cents) sized stain on the ground and would only drip for 10 minutes or so after I shut it off. in 3000 miles it would be down 1/2 quart of oil...
Well 3 weeks ago I stopped and noticed a HUGE stain now. I checked the oil and was 1 quart low. I filled it then I drove 90 miles the final week before parking and was down another 1/2 quart...
I am figuring the rear main seal is gone. I did some research and it seems these are common to go in the 3.0? What seal is the best to get? should I get the seal right from the dealer? or I will run into the same problem and go with a after market? I also learned that the crank shafts can get a groove in them and it's good to put a new "speedy seal" where can I get one of those?
Also for some strange reason I take the tranny out and the rear main is good ( I seriously doubt it) is there anything else that could be leaking that I should check when I have the tranny out? Can I remove the tranny with the factory exhaust still in place? it looks like it can squeeze just by it?
View 7 Replies
This morning the passenger side wiper on my 89 Ranger stopped working. I heard a clunk noise and it stopped but driver side still works. What should I check first? I'm guessing a shaft came off but don't know where it is located.
View 14 Replies
I noticed a strange vibration in the 83 Ranger I own, it has the 2.3 and a 4 speed. When getting up to speed around 35MPH it would start vibrating, and the speedometer needle would bounce around and read slower than it was actually moving. This would start in 3rd gear, and continue thru 4th unless I let off the gas while it was in gear, then it stopped and worked normally. I put a grease seal in the tail section when I first got the truck, and when I pulled the driveshaft again today the seal was mangled and bent, plus there are metal particles around the main shaft where the seal goes. I figure the tail shaft bearing is shot, and I also found damage to the yolk with the U-joint, the shaft has a worn spot about 1/3rd the way around.
View 2 Replies
Today I took the bed off of my 99 ranger. I was sitting on the cab looking down at the rear axle noticed the drive shaft was not entering the rear diff perfectly straight. As I looked further into it, I noticed the distance between the rear spring on the passenger side tire, is noticeably different. To visualize it, the wheel, at the bumper side of the axle, has a shorter distance between it and the leafs than the cab side. Not massive, but a few inches, and it's noticeable now that I can stand over it. I'm beginning to be very annoyed by this truck and it's previous owners, whom I take it , scammed my brother quite well with a $5k tag for a truck with so much not right with it. It's about to become my yard art for awhile.
View 8 Replies
Can I take off the output flange on the tranny and use a slip joint, with out changing the tail shaft?
View 1 Replies
I have an '04 Ranger Edge 3.0 with a severe coolant leak. It appears to be coming from the area where the head/water pump housing meet. I have been told I've lost the seal behind the pump on the timing cover. Is there any way to know for sure? Will I be able to tell, once the pump is out that it isn't coming from the head side? Are there any "special" instructions for re-sealing after replacing pump?
View 6 Replies
Okay, I have a P0720 code. I bought the Output Shaft Speed Sensor and read that it is on the back end of the transmission.
Need to confirm that it is on top of the transmission, near the tail end? Why are parts that go bad always in the most inconvenient places?
View 14 Replies
