Ford Ranger / B-Series :: Trans Malfunction - Oil And Exhaust Leak?


Aug 5, 2013

The problem I have is the truck won't move in o/d. If I put it in revers 1,and 2 it works. A little back ground. 4 years ago the trans went out of my 95 4.0 4x4, had it rebuilt so it has 0 miles on it. It got really cold that winter had lots of trouble getting the trans and torque converter lined up. motor went bad on me. A few months ago finally had some money to spend bought a 98 explorer sport with a 4.0 x code motor. the motor runs fine apart from an oil leak and an exhaust leak. the exhaust leak is no big deal I just haven't gotten the system tight yet.

View 8 Replies

Advertisement

Ford Ranger / B-Series :: 1998 - Exhaust Leak Sound Under Hood?

I have a 98 Ranger 3.0 with a standard transmission. The truck has 240,500 miles so far. It runs just as good as the day I got it 11 years ago, doesn't use any oil and still gets 23 MPG. Last fall, it developed what sounds like an exhaust leak under the hood. It seems to be coming from the area of the EGR valve. The trouble is that I can't feel it or smell it. I have carefully felt the entire length of the tube running from the EGR to the exhaust manifold and cannot feel any leaks. There is no soot or any other evidence of an exhaust leak.

The noise isn't there for the first minute or so that the truck is running. I would think that if I had a cracked manifold or some other such leak, it would be worse when the engine is cold but this is not the case for me. It is most noticeable when pulling a hill as slow speeds in a higher gear. I have checked for codes (no CEL) and there are none. When I first heard it I figured that I would wait until it gets a little worse and I would be able to find it. Its been been over 8 months now it has remained the same.

View 1 Replies

Ford Ranger / B-Series :: O2 Sensor Heater Circuit Malfunction / Evaporative Emission Control System Detected Large Leak

I have some codes on my ranger 2000 here goes

P0141: o2 sensor heater circuit malfonction (bank 2 sensor 2 )
P0455: evaporative emission control system detected (large leak)

Now I will need to get that fixed cause I don't know where to look and what to look for ... For the leak I know there is a big crack on the plastic where the gas lid is could that be it ?

View 2 Replies

Ford Ranger / B-Series :: 2003 - Valve Cover Leak / Exhaust Smell Then Started Bogging / Dying And Shaking

I have a 2003 ford ranger 2.3 vin d 5 speed, this truck originally... Took it in for wires plugs front brakes fuel filter battery and added a small cold air intake. We discovered a valve cover leak and while repairing guy drops a screw into a valve and when finished he started it lodged the screw between the valve, shearing off a cam sprocket bolt. Throwing the timing. 2 valves on the exhaust side were bent and replaced. no damage to the head.

Timing was reset and the truck was running. 2 days later truck is running/had a hint of exhaust smell then started bogging dying and shaking, at which time we got an 02 bank2 lean code and fixed that. it cleared code and didn't fix it. From there we replaced coil, imrc intake bc of a crack, tried and check all vacuum, reset the timing. Timing would slip before but no longer than 10 minutes every time truck started.

Found the hole in the timing cover that holds the bolt to torque? to harmonic balancer was broke. replaced along with the diamond washers and cam sprocket bolts. timing finally held crank sensor was adjusted. truck came home for one day running good, we had removed the cold air intake and replaced the factory air intake. next day it was so slow outta first gear, you must baby the throttle, if you floor It, it sputters and kinda pops, truck stays slow all the way to about 10 mph and 2000rpm then it begins grabbing speed, 3000rpm is where this truck shifts the best, 2nd is better, third better than that.

As rpm increase the truck runs better, it idles steady at 1100-1200rpm at stops with an audible miss and then struggles again on takeoff. Here what im wondering, the truck has an abs sensor that just came on, but no codes showing now.tomorrow I wil run matko determinator 3.0 on it. and test the catalytic converter. first how do I check the timing belt to see if it stretched? do these trucks store the p.i.d.s. koer or kams that could cause one, all, or any of this and if so do I have to have it flashed from ford or can you manually do this without a drive cycle test.

View 2 Replies

Ford Ranger / B-Series :: 2011 - Temperature Gauge Malfunction?

I have a 2011 xlt extended cab with a 2.3l 4 cylinder. The truck is great... I put 120,000 miles on it in under a year.

But about a month ago the temperature gauge started malfunctioning. for what ever reason -- the truck is NOT over heating-- the gauge would increase past the "H" and then the temperature light would come on. Because the truck thinks it's overheating -- the engine goes into a "safe mode" and runs with no power. When i shut the motor off and turn it back on temperature gauge resets and the truck will run fine.

Then in another 50 or 100 miles it will do it again. Why is it doing this? I took it to the dealer here in Columbus, Ohio and the mechanic installed a new thermostat and a new "control modulator" (and a part -- not really sure what it is called) anyway, the truck is doing the same thing and the mechanic still does not know

View 3 Replies

Ford Ranger / B-Series :: 1999 - Trans Won't Shift Into Any Gear

i have a 1999 mazda troy lee b3000. The truck has a 3.0 flex fuel and 4r44e and when you go to drive it. turn the key engine fires up but the trans won't shift into gear. Here is the back story.Bought the truck brand new in 99 I'm the original owner it was a daily driver up until 2 years ago. the truck has over 300k miles and still ran great but the camshaft was starting to go. I was gona replace the cam but came across a killer deal on a new engine. picked up another 3.0 flex fuel with 50k miles. drove the truck into my garage removed the old engine installed the new engine. got in the truck turned the key and the new engine roared to life.

I went to put the truck into gear so i could get it out of the garage and go for a test drive and nothing. went to put it in drive and again nothing. no matter what gear its put in it doesn't move at this point i was confused and decided to quit for the night. That was in 2011 its now 2013 the truck has just sat there sense then. I've tried anything and everything even went as far as swapping transmissions and computers with no luck. I took the trans apart I don't know how many times can't find anything wrong with it.

View 4 Replies

Ford Ranger / B-Series :: OD Light Flashing Off And On And Trans Slamming Into Second

I have a 98 Ranger, 4.0 automatic 4x4...I just replaced the upper and lower intake gaskets and after fumbling with the pug wires to finally get them in the right order, I suddenly find my OD light flashing off and on, and the tranny slamming into second, and once in top gear can feel the OD popping in and out? From my reading here it looks like a pretty common problem, but the solution isn't as clear...

The vehicle set for about 3 months while I healed up from a injury, and and was working just fine when I parked it...due to the blown lower intake gasket. I am thinking I have a vacuum line not connected or wrongly connected...or some kind of over looked item, but I can't spot anything...should I get a code reader and go from there...

View 14 Replies

Ford Ranger / B-Series :: Trans Sometimes Takes A While To Go Into Gear When Put It Into Drive

I have a 98 XLT 4.0, auto trans with 109K miles and when it's really hot outside and it's been driven when I start back up and put it into drive it sometimes takes a while to go into gear. A friend says the transmission fluid doesn't look too good and it smells. Obviously I have a transmission problem but my question is would changing the fluid do any good at all? Since the tranny is bad what harm could it do? The fluid was never changed previously.

View 6 Replies

Ford Ranger / B-Series :: 2002 - Trans Hesitates - Shakes At 65 - 70 MPH?

02 ranger 4.0 v6 auto has 110000 miles on it. at highway speeds 65-70mph feels like it strugles to shift, truck will shake and bounce some. when this happens rpm's jump from about 2200 to 3000-3200 after a little bouncing rpms drop to normal. issue seems to be the worst going up hill but will happen every time i hit 65-70. Also the truck will not bounce or shake with the OD turned off and seems to run fine this way.

tranny fluid/ filter just replaced with no change. new plugs and wires

View 3 Replies

Ford Ranger / B-Series :: 1999 - Trans Slipping In 1st And 2nd Gear?

I have a 99 Ranger 3.0L automatic, ext cab, 2 wheel drive. Door sticker show code "T" which I looked up as the 4R44E. The trans seems to be slipping in 1st and 2nd. Thought it was "reared shudder", from a "limited slip" differential but mine is not limited slip. just the regular 8.8 with 373 gears.

Wanting to know what if any options I have for buying a new / rebuilt tranny? I've seen where depending upon the year and motor, Ranger can have 4r44e, 4r55e, 5r55e, etc.

View 3 Replies

Ford Ranger / B-Series :: 1996 - Fuel System Malfunction - Won't Restart If Sit For Sometime?

My Ranger has been a great truck but over the last 18 months ther has been a intermitent problem with the fuel system. It would run out of fuel ( foaming spray to nothing at the fuel rail ) and if you let it sit it would start and run after 8 hrs to a couple of days. Now it is all the time. The last time I let it sit for a week in a parking lot and it started, let it warm up and turned it off to move my other truck and it would not start when I returned. I have changed the fuel pump 3 times, 2 fuel filters, relay and pressure reg. on fuel rail.

View 5 Replies

Ford Ranger / B-Series :: 2001 - Auto Trans Won't Drive / Reverse?

Daughter driving truck truck quits moving, I get there no drive and no reverse, has low and 2nd manually.

drive truck home, flush trans and cooler, road test all ok. this was 3 weeks ago.

This morning did it to here again, no drive and no reverse, she drove it home using manual low and 2nd.

I get in and when put into drive it feels like it tries but doesn't go all in, same with reverse. pulled it into low and vola I now have drive and reverse again

I'm thinking a we may have a bad or going bad shift solenoid. What I need to know is, is any of the solenoid valves on when in reverse are they the same as when in drive?

View 3 Replies

Ford Ranger / B-Series :: Hard To Get Into Gear - Trans Partially Engaging

I have a 99 ranger 4x4 4.0 V6 with 200K miles..I just had the slave cylinder replaced and bled however, it is still hard to get into gear and when at a stop light with the clutch pedal pushed in all the way the truck tries to move forward as if its in gear. I took it back to the shop and the mechanic says that the hydraulic system is working as it should and the problem could only be the pilot bushing failing and causing the trans to partially engage. The clutch and previous slave cyl only had 25K before the slave cyl failed and started leaking!!

View 12 Replies

Ford Ranger / B-Series :: 1993 Manual Trans / Hard To Shift Into First

I'm having a little issue with shifting into first. Once in a while it simply will not go in, like you're pushing the shifter against a brick wall. If I turn off the truck and turn it back on, it works absolutely fine. I can shift into 2nd-5th no problem at all times. Is it just the shift linkage, or...? I'm not really sure where to start.

View 7 Replies

Ford Ranger / B-Series :: 1996 4x4 Manual Trans Missing 3rd Gear

1996 4x4, manual trans. Wants to kick out of first, and when shifting into 3rd I have no gear. Doesnt grind, just goes in as though it were neutral.

View 4 Replies

Ford Ranger / B-Series :: 2001 - Trans Judder When Coming To A Stop Moving At Around 3 - 4 MPH

2001 4.0 4x4 auto trans... Problem, tranny judders when coming to a stop moving at around 3-4mph. Engine drops to around 500rpm and maybe one second later returns to normal as the tranny seems to disengage. No judder or shifting problem when accelerating.

View 5 Replies

Ford Ranger / B-Series :: 1986 - Diesel Swap - Engine And Trans Combos?

I have A 1986 ranger with a 2.9 v6. I am thinking of doing a diesel swap and I am wondering what engine and trans combos would work best for this. I was thinking 4bt but there are may other options that could work.

View 14 Replies

Ford Ranger / B-Series :: 2000 - Trans Won't Engage - 4R44E Shift Cable?

I bought a 2000 Ranger 4x4 3.0L auto today from the neighbor guy sight unseen with a "bad tranny" for $400. I'm very unfamiliar with the Ranger family, but long story short:

When moving the shift lever, the trans doesn't engage. It needs to be engaged from underneath. Do the cables tend to stretch, or break? I can't find any adjustment on it anywhere.

View 5 Replies

Ford Ranger / B-Series :: High Beam Malfunction - Moving Forward Headlights Cut Out Completely?

I have a 1995 ranger four letre 5sp, dubbed Beula. I figured there'd be a few gremlins and there was and is, which I know to be more common than not in older trucks. The top priority is figuring out why when I push the lever for the high beams forward, the headlights cut out completely, whether in gear or not, and I don't know where to begin troubleshooting. I've surfed around the forums looking for answers and really only found conjecture.

View 14 Replies

Ford Ranger / B-Series :: Pinging Occasionally From The Exhaust

Since putting my new exhaust on (post-cat)... I've had this "ping" occasionally from the exhaust. Sounds as if someone is taking a small metal bar and hitting the exhaust. Random intervals, pretty loud, does it whether the engine is off or on. Only does it when warmed up though. I can't narrow it down due to the randomness of it.

View 5 Replies

Ford Ranger / B-Series :: 1990 - Trans Started Making Rattling / Grinding Noises

1990 Ranger 5 speed... The tranny has recently started making noises, first I thought it was the throw out bearing but I am afraid it is more than that. As I go thru the gears the trans makes rattling/grinding sounds: in 1st, 2nd, 3rd and 5th it is loud but 4th it is quiet. What might be going on inside the tranny....

View 14 Replies





Copyrights 2005-15 www.bigresource.org, All rights reserved