My wipers are just beginning to rust. I'm either taping the truck and masking off the wipers but would rather take them off. I don't understand what is holding them in place. First post on my first Ranger that I just bought.
View 4 RepliesI lost the windshield wipers, speedometer, dome light, door alarm. Check all the fuses I can find all are ok. Whats wrong.
View 7 RepliesIs there any way to repair rust spots so the rust will not return aside from putting new metal on it? I've used Bondo before but it rusts again after a while.
View 3 RepliesRecently my father bought a 2007 Ford Ranger from a dealership. I have only noticed the other day that the bottom of the door is forming rust. What is the easiest way to go about fixing this.
View 4 RepliesWiper problem is that they only work on high. The symptoms are as follow. The relay is working as the controls are ran thru the intermittent steps. I have tried two control switches and they acted the same. So, I believe the problem is in the motor. There doesn't appear to be any wire problems on the plug so it must be inside the motor. Could this be that grease problem inside the motor and it just needs to be cleaned and re-greased?
Radio, Has power to the plug but doesn't work at all. It doesn't appear to have a head unit fuse that I keep reading about. I have not tried to hook it up direct yet but will try that tonight. I am trying to get this truck ready to sell and need to get these items cleared up.
It is a 2001 XLT Extra Cab 4X4 with a 3.0.
1995 ranger 4,0 4x4... when started up, wipers go 2 times and then stop, but cant turn on again, also blower and 4WD stopped work....
View 4 RepliesCooler weather here in bc now and my ranger is completely ice over in the morning. I get in and the inside of the windshield is also iced completely over. I turn on the defrost and fan and go outside to scrape. Then come back inside the truck and scrape the inside of my windshield. I have 3 big dogs inside the truck most of the day who fog up the windows so I usually open a window or put it on defrost. Also a small piece of the driver side door lining is missing.
View 1 RepliesJust picked up the truck 1995 Ranger XLT. 3L...5spd...4x4...no power windows or door locks. The key buzzer only buzzes for a few seconds, if you move the ignition it buzzes for a few seconds each time its moved. The wipers only work when the buzzer is dinging. Also..the wipers when turned off stay in the up position. I replaced the ignition key mechanism and the on off wiper relay. What am i missing in this weird scenario??
View 1 RepliesMy 96 ranger had lost a brake pad coming out of the mountains. I replaced the rotor but the ABS light came on as well as the check engine within a week. Several issues the clock spring was bad, replaced. The cam position Sensor was bad, replaced. I had this at a shop in a small town. While I was there they ran diagnostics.
At first the ABS module was sending data and gave them some info. Suddenly there was no more data stored in the module. They ordered a new ABS module installed it and replaced the LF sensor cable. Both sensors were cleaned prior to this.
The new abs module required a trip to ford to reprogram. At the shop they still could not get the light out. I took the truck home to my ford dealer and they said bad abs. Got a new (rebuilt Mfg discontinued) Installed and ford said this was bad with a code c1102. 4 w 4wd installed needs 4 w 2wd. ordered a new abs. Ford said same code again and the tech said that the ABS is not communicating through the obdii port.
My thoughts are the reader they used at the small shop was defective and either shorted out something or blew a fusible link. I am told this is 4 wheel abs with the rear sensors are on the pumpkin but after looking at the diagrams I do not see a RABS fuse. I have tested all fuses, and the shop replaced several relays. The pcm and ABS diodes check ok. Perplexed.
I have a 1988 Ranger with the 2.9. 2wd, xlt. It seems that my wipers have no power. I put a test light in the fuse panel where the 6A cb is and no light. To verify I wasn't doing something wrong, I put it in the dome light and tester came on. I tried with the wiper switch on interval, low & hi. I can't seem to find where the power comes from to follow back from the fuse panel. The washer fluid doesn't work either. No clicking from relays or anything.
View 2 RepliesMy engine has 2 ignition coils, and b went bad, but which one is b. ?
View 9 RepliesI have a 1996 Mazda B2300 & I heard that it is similar to the Ford Ranger.
Well the thing won't crank or start.
This is what I have done so far. I wanted to put a RPM meter on it. I followed YouTube videos on how to do it. I cut the Tan wire w. the yellow stripes & try to connect the wire to thr RPM meter. Then it won't start soo idk what to do. I also took put the PCM too. (I was looking for the wire) Now be honest, I talked to a mechanic, he said thag I might have blown my PCM or Blown another fuse. But when i put the key in to crank, it won't start ot click at all. The lights come on & it wants to start but won't start.
Then my mechanic tried to start it by the... Idk what it is called but you can start it & it wont evet start. It will crank like crazy but will not start at all.
I have a 96 Ranger 3.0 auto that is hitting 300,000 miles. I've got a 302 that i build for my F150 but know i'm thinking of transplating it in the Ranger. Is it a big deal in putting a SB in place of the V6.
View 4 RepliesI seen on this site awhile ago something about a fix for the heater control door, I have a 1996 Ranger and all I have is Hot heat and cannot cool it down with the temperature control.
View 2 RepliesI'm in the middle of replacing my pump. With the new pump are a plastic washer and a small rubber o-ring but no instruction where they are supposed to go. They didn't know at auto zone and I haven't heard them mentioned on any youtube video. I found a crushed torn up washer similar to the plastic one in my catch pan. Maybe it is supposed to go in around the high pressure hose connection.
View 6 RepliesI am working on a 96 ranger 2wd the front brakes were shot or nearly so,about 1/8 in left and cracked. Changed them this morning at 5am because that is the cool of the day (104 today) everything up front works fine but the howling and nails across the chalk board from the back was still there. Took it to my freindly les schwab and they told me it needed axle seals on one side and the noise is from the gear lube on the shoes. they wanted 800 bucks to fix everything, went and bought new shoes,new seals,gear oil,and gasket for rear end cover it is an easy half hour job. As I was driving home tonight from the parts store the noise stopped so now i am worried either it was a rock stuck between the drum and backing plate or something broke. everything sounds and works fine....
View 2 RepliesI have a 96 ranger with a 4.0 and an automatic transmission that has a horrible oil leak when cold. The leak looks to be coming out above and behind the oil filter. After running for a few minutes the oil leak appears to go away.
View 6 RepliesMy ignition key is stuck / locked in the off position. The first time this happened I jiggled the key while moving the wheel back and forth and it turned. The next time in the truck nothing worked. I let it roll back a bit then tried, pushed the clutch in and put it in neutral, etc it did not move. (Just had the clutch and clutch hydraulics replaced.) The wheel is locked. The key removes from the cylinder.
I know it is easy to replace the Ignition Lock Cylinder when you can turn the key in the run position. How to remove it when locked in off?
Originally started with a p0302 code, and it cleared. CEL came back on with codes p1131 and P0401. First time with an 8 plug 4 cylinder. Truck has 263000 miles, and still original (metal) DPFE sensor. 1996 ranger 2.3L.....
View 1 RepliesMy 1996 Ranger Supercab XLT has the stock radio with 6-cd changer. The unit works fine but only the frequency/clock display lights up. I'm not sure where to start to fix it.
When a problem first occurred, the frequency/clock display flickered/dimmed randomly (and I think the other lights were fine). It was in the shop a few times for a fuel pump problem (the after market pump was actually not compatible and it took a bit to figure that out), and at some point after I got it back I noticed the display was fine but the remainder of lights didn't work.
I don't know if the shop did something or the failure behavior changed. What to look at? I can open the radio and fix that if needed (or replace it).
I have been hauling a lot of garbage with my 96 ranger this last week. The differential has been making a little more than usual noise like growling, but it has always been smooth, now all of a sudden it shakes like a tire out of balance up to about 55 then it is like a switch is thrown and everything quiets down and the shaking goes away, until i get around 55. I haven't climbed under the truck yet just checked the tires and grabbed the drive line they are all ok,i don't see any leaks so it is a head scratcher. Hopefully it will be something easy, but it hardly ever is.
View 7 Replies