Ford Ranger / B-Series :: 2003 - Shake After Start Up For 10 To 30 Seconds - Converter Leaking Out?
Aug 28, 2012
I have a 2003 Ranger 4x4 with the 5speed automatic. It has 215,000 miles on it and I don't drive it regularly anymore. Lately, I've noticed that it will shake after start up for 10-30 seconds. This only happens after it has sit for a few days or a week. After it warms up, I can drive it and stop and start it again and it has works as usual.
Is there some way the convertor is leaking out fluid and it shakes until the convertor is full again? Or is something else the problem. I've changed the fluid two or three times during the life of the vehicle.
View 4 Replies
Advertisement
So it often just cranks for 15 seconds before it fires. I put the fuel pressure guage on it and you turn the key on but don't engage the starter it goes to 30 psi then back to 0 in a 2 second time frame. It then stays at zero. when you engage the starter pressure slowly goes up and it starts running while running its a consistent 60 psi.
I presume its the fuel regulator but why does it not go up to 60 psi and why does it just stop with the KOEO? Is it reasonable to just replace the regulator? or should I be replacing the fuel pump to at the same time? I will be doing this from under the truck since there is a lot of hard mounted equipment in the bed.
View 4 Replies
SO ive been after this problem for a while now. When my truck has been sitting for 2 days or its a semi cold morning (35 degrees) the truck has a problem not starting. Ive changed the fuel pump, the starter (my starter was going bad anyways and I thought it could also solve the problem I was having), and the battery was just tested. If I leave my key on Acc for like 10 seconds then try to start, it starts right up or if I just re-start right after the first. Now I am leaning towards this being a fuel pressure problem but I am not sure where to start with that... My mechanic also said that it could be the wire that connect to the battery terminal because they can get corroded.
View 4 Replies
I am a new owner of my first truck and it is a 2003 Ford Ranger 3.0L Extended Edge with 138,000 miles on it. I keep getting a chirping noise coming from driver side of truck. It only happens when I have the AC on. I can turn AC to just air and the chirping stops. This only happens when I am driving. If I have my truck parked in drive with the hood up, I go and turn on AC full blast and I hear no chirping. I can see AC compressor turn on a few seconds after I start the truck and it is not cycling on or off every few seconds as some people I have asked told me it should do. AC air is ice cold so I should have enough freon. Now this chirping is not constant like a machine gun going off but just about every 5 seconds or so it would chirp. I have heard of bad camshaft sensors causing chirping but would that happen every few seconds and only when you are driving down the road with the AC on? Now I have noticed when truck has sat for a long time I get belt squeal for a few seconds and it then goes away. I think the squeal goes away when AC compressor starts because I observed this when looking for this random chirp. Any clues?
View 4 Replies
'03 Ranger, 2.3L. Runs great except at idle. Code p0171. Replaced IAC, no luck.
Brake cleaner leak test definitely results in engine rpm change right around "butterfly rod" plug in front of intake manifold near no. 1 cyl. I'm pretty sure that's the problem - the plastic plug blew out. I watched a video showing repair, but it seems lacking.
I do not want to loosen up intake for access - I'd rather remove steering pump and gain some access to plug it up. There still isn't much access but, but eyeballing it, enough to plug, I think.
Three steering pump bolts came out easy. The fourth one is behind fluid line - extremely difficult to access, imo.
Somehow try to remove pump for access to intake hole, or bite the bullet and remove intake manifold for access?
View 6 Replies
2003 ranger 4.0 5 speed .... Pretty new to the car/truck world only 18 and this is my first truck, I traded my focus for it and so far so good. Its my first manual but i got to tinkering and i noticed some oil build up under the front end so i got to looking and found this, wondering if its an issue, should I try to fix whatever is causing it or take it to a mechanic. Looks like between tranny and engine to me.
View 2 Replies
I have a 95 ranger with an overdrive auto. If you put your foot in it the converter wont lock up, you can get the tack past redline, but if you let off and the rpms drop below 2000, it locks up and holds until you apply the accelerator to much and it kicks it back out. Also the speedometer bounces and may not read right, abs light is sometimes on and it won't idle below 1000, I've checked for vacuum leaks already.
View 2 Replies
I don't have a Ranger or B-Series, but I do have Ford's older B-Series counterpart. 1979 Ford Courier, 2.3L/5-spd. I have had a bad rear end shake since I bought the truck nearly three years ago, so I'm sure it existed well before then. It only happens around 60-65 mph, and there is also a kind of buzzing/humming sound whenever I'm coasting to a stop in neutral. I have:
Replaced and balanced the tires several times
Rotated the tires several times
Replaced all four wheel bearings
Replaced steering linkage
Replaced front suspension
Balanced driveshaft twice
Replaced driveshaft center bearing
Replaced all three U-joints
Checked rear wheel lateral and radial runout
Had the front end aligned three or four times
Checked engine and trans. mounts
And yet the issue persists. I am stumped and this problem is driving me bonkers!
View 6 Replies
I have a 98 Explorer upon startup is horrendously shakes. What went to hell in the transmission?
View 6 Replies
So Im working on a 1998 mazda b4000, frost plug blew out going down the highway changed the engine because it got cooked pretty bad. The wrecker engine I got for what ever reason will only run good if the driver side of coil pack is done 5,6,4 any other order truck wont run at all. Misses enough to shake the truck at around 80 km/hr otherwise its pretty good. Also the engine I got came factory with no egr.... no provisions nothing. exhaust manifold capped off, seemed kinda odd.
View 5 Replies
1999 ranger 2.5. 135k!So I started with a tune up all motorcraft, fuel filter and air filter. Did nothing! So I did compression check all cyc 150psi and above. So I did leakdown, had air leak at dip stick and valve cover, So I asumed head gasket. Pulled head and found 3 head bolts on passenger side had carbon deposit bluid up really bad, So replaced head gasket all surfaces clean and flat. Still didn't fix it!! My symptoms are better than before hd but still have a engine shake and flashing cel at 55 plus mph and p0303 pending! Coils tested good but going change them any way tonight!I'm stuck on this one checked everything 3 times and then again...
View 7 Replies
I have a 05 f150, on initial startup ALL of my needles shake for about 5 seconds and then return to normal operation. What is wrong.
View 2 Replies
94 Ford Ranger 2.3L
I started to have a slightly rough idle a while back, but not severe. I figured she was just aging a bit.
Changed plugs. Check engine light came on. Changed plug wires. Then I had a couple of episodes where it started to lose power and idle really rough (stalling). Both times it stopped after a few minutes. Had code read- they said it was coils. Replaced ignition coils. Check engine light still on, but it went a few weeks without power loss.
Tonight the loss of power returned and didn't leave, and I had a glowing red catalytic converter after I limped home 20 miles (hope I didn't do any serious damage, I was stranded.)
Found this post : [URL] .... But there's no resolution.
So, I'm probably dealing with a misfire, and I'm sure I torched my cat after tonight. So any other easy diagnose/fixes for a misfire? I'm a shade tree mechanic- so I know just enough to get myself in trouble. If I can't get a resolution soon it will be off to the mechanic (which, maybe I should have done 1st...)
View 2 Replies
My 03 ranger with a 2.3 I4 does not want to restart when it is above about 80 deg outside and engine is warm. Will crank, but as soon as fuel in line runs out it stalls, like a vapor lock. After about 45 mins can push start normally( has manual trans) but have to wait about 2 hours to use starter to start.
View 11 Replies
Okay so the other day my ranger wouldn't start after i got off work, it would turnover only occasionally but now it wont even do that. I've tried the fule turn on/off switch underneath the passenger glove box. I unscrewed the fuel like valve cap and pressed the pin but the fuel like barely squirted out so does it mean my fuel pump is bad or what??
View 9 Replies
Specs: 2003 Ranger Edge / 3.0 V6 / 5-speed 4WD / 238,000 miles
Yesterday my truck was in the shop for repair. Intake gasket, Transmission fluid change, all heater hoses, thermostat, serp belt and coolant flush. When I picked it up from the shop, which was after closing, I noticed a knocking on start up. From past experience on a different truck, it sounds like a cam that isn't oiling. After a few minutes the knock goes away. I drove for a few miles, turned off the engine and started it back up and no knock this time. This morning I started it, knock was back but went away after a few minutes. Oil was changed about 1500 miles ago. Running pennzoil 5/20 with a K&N filter. Up until yesterday the engine has been completely quiet. Was wonder if something may have clogged the filter or the drain back valve.
View 6 Replies
I have a 2003 Ranger 2.3l with 327k miles on it. I recently replaced the belt and now it doesnt want to start. The belt is on correctly and tensioner is tight. The battery is fully charged its just not firing up and starting. All connections are good, the ac and power steering pulleys are relatively new. Now i have been stuck tryin to fix it for a week...
View 8 Replies
My 03 Ranger 4.0L has become a mystery that has baffled every one I know. Everything was fine and I ran home to something from my house was in there maybe 10 minutes came out and the truck wouldn't start. it doesn't even crank over. out of the clear blue. I had a friend who works for a garage check it and he thinks timing chain. Since then I have been told it wouldn't just fall off sitting there with no indication at all there was a problem.
Thought maybe PATS system. Its in order. Put in on a computer from auto-zone and it shows a check engine light but the reading is there is no codes in the computer on file. I am at a loss. Its been months and I really cant afford to take it to a garage right now. Its the strangest thing ever no crank, no stalling just nothing I hit the switch it lights up like its ready to start and nada.
View 3 Replies
I have a 2005 ranger SOHC 4.0 new rebuilt engine It starts then dies after a few seconds then doesn't start at all unless it sets for a few hours or over night and will do same thing. It has 60 psi on fuel rail, good spark I'm starting to think my PCM is causing all this?
View 14 Replies
My 2003 ford ranger 3.0 v6 is having a misfire on start up and it is located in the forth cylinder. Where to start to get rid of this problem. i have already changed all my plugs wires and even the coil pack cleaned out the maf and looked for possible leaks. the car shakes really bad at lights and the check engine light starts to flash. Need diagram of where all the cylinder numbers are at and maybe the firing order?
View 14 Replies
I have an 03 Ford Ranger 4x4. Great truck and runs great just with one small problem. For whatever reason, every single time, the a/c only blows un-cool air (not hot) when I start the truck. Then, and only then, after about 30-40 mins of constant driving around does the a/c start working properly and blowing COLD air. After that it works great but it always takes about 30 mins after I start the truck for it to work correctly.
View 4 Replies
