Ford Ranger / B-Series :: 2007 - Air Flow With AC And Heat Is Low?
Jun 3, 2010
The air flow with ac and heat is low on my ford ranger. I can hear the blower change speeds, but on high, it barely comes out. The temp is fine and achanges from cold to hot like it should. i had the ac checked out by a shop that that does free checks - no problems with lines or compressor. I replaced the blower motor. The air changes from defrost to floor and all the positions fine, but the air flow out all the vents just isn't what it should be. It was working fine the first couple of days. I've read about the blend door motor, but I haven't read about people having this exact problem. I am almost to the point of bringing is to the dealer, but would rather fix it myself.
2007 Ford Ranger ... 6 cyl. 3.0 L ...
View 14 Replies
Advertisement
What controls where the air flow is directed in the cab? I've just finished replacing my power steering pump, ac compressor, dryer, and ac hoses. I have air flow to the defrost and some on the floor bu none coming straight out. It worked normally before so I did something. ('96, 4.0, auto tranny, XLT).
View 1 Replies
I have a 2000 Ford Ranger 3.0L engine, 2 wheel drive, with automatic transmission. Check engine light came on about 3 months ago. checked with scanner and P0401 EGR flow insufficient came up. cleared it and it came back. truck seems to be running fine. I didn't take autoshop as a kid, so i probably will need a little hand holding on this one.
View 14 Replies
Truck is a 1993 ranger 4.0 ohv
Ok I have been getting 157, 158, and 159 codes. I have cleaned and replaced the MAF with no success. I checked the voltage to the sensor 12v, checked the voltage from the signal wire and it is to high. It has been high on the cleaned unit and on both replacements, so I am thinking it is not the MAF, but what will cause it to register high. I cant get the signal voltage below 1.9V at idle.
Signal also reads high with the ignition on and the engine off. What would cause the voltage to be high, I have read it could be an IAC but I would think that would not effect it with the engine off.
View 14 Replies
I got an 0401 EGR Flow Insufficient last week. I cleared it and it showed up again after a couple of days. I replaced the EGR Valve and the 0401 reappeared. I replaced the DPFE and the code did not reappear. Great!
About a week later, I got an 0402 EGR Flow Excessive. New EGR Valve. New DPFE. The hoses to and from the DPFE to the tube look decent. They don't appear to have any build up inside. Code 0401 or 0402 to the tube?
My first instinct is to replace the EGR valve again, assuming the one AutoZone gave me is stuck open. Is there any servicing I can do to it first? Like maybe soak it in carburetor cleaner? Or spray it with WD-40?
View 6 Replies
So I had a post up saying "is MIL P1444 a urgent fix" and I got "no". On an other website though it said that it was an urgent fix. They said it was "similar to running a bad catalytic converter. You don't want to do it."
P1444:
Possible causes
- Faulty Purge Flow Sensor
- Purge Flow Sensor harness is open or shorted
- Purge Flow Sensor circuit poor electrical connection
So I located the purge flow sensor and look at the tube that connects to that,the canp solenoid, and the carbon canister. Nothing looks bad, but I did notice that the tube that connects to the carbon canister to the solenoid is not connected. The part that connects to the carbon canister dry rotted off. So I turned on my car to see if anything was coming out of that tube or air and there was nothing (not sure if that's good or bad). Also a week ago when I filled up my gas tank (before the check engine light was on) a lot of fumes were coming out of the tank while pumping.
The scanner i use also lists the secondary air system, the EVAP system, Heated catalyst, and the AC refrigenant has red X's, but they weren't continuous.
View 14 Replies
My aforementioned ranger does not seem to heat up. Unless it is 95 degrees in the shade.... I have movement in the dash meter. Some - it will come off of the bottom - to not quite the c - then immediately dive back to less than cold ( which I realize is not possible) - engine seems to run fine. Use 93 octane or it knocks like a diesel. 135 K - I changed the thermostat. Less movement on gauge now than Before. Coolant level is fine. I read something in another post about the blend door. But my engine temperature doesn't even seem to be getting warm so how would the blend door be effecting that? I am an electrician not a mechanic, however I do all my own mechanic in in self defense. Since I cannot afford mechanics.
View 9 Replies
I have a 85 Ranger with a 2.3L engine. I'm not getting any heat. The temperature gauge never moves off of C, except when stuck in stop & go traffic. Even then it doesn't come up much. I tried to fix this last year by putting in a new thermostat, but it didn't work.
View 6 Replies
1994 ranger 3.0 .. New: water pump, htr. hoses, radiator, thermostat, pulled & flushed htr. core. (2 year time frame) ....
View 5 Replies
98 ford Ranger 2.5L.
I have not heat from the vents, doesn't get warm at all. If I idle the enginer in 30 Degree weather it gets to almost the C.
Upper Radiator hose is hot, I have verified the thermostat is new and it opens at 192 degrees as it should. Replaced the Water Pump, Fan spins freely.
I have attempted to burp the system, it isn't kicking out anymore air from the lines that I can tell. I used a large funnel and filled it with Anti-freeze, it filled the radiator, burped the system and the reservoir filled to overflowing. All with the engine hot. (To be specific the funnel was always full of fluid so no air could get sucked backwards)
The heater core hose on the left when looking from the front of the vehicle does not get hot, the one on the right gets warm. I theorize that the heater core is clogged up somehow and that is why that left line doesn't get hot. There is no fluid in the cab of the truck from the core.
View 9 Replies
i have a 2001 ranger 4x4 the problem is sometimes it will switch into 4 wheel drive and sometimes it wont just hear clicking noise ,i'm preety sure it doenst have a vaccum.
View 14 Replies
I have a 2002 Ford Ranger 3.0L truck that, all of a sudden, has a problem with the HVAC system that blows air only thru the defrost vents even when selecting any other vent levels (defrost, face/middle or floor levels).
I did find a thread on another forum regarding this problem, only it was for the 95-01 Ranger model years, yet they say that the 2002 Ranger is not the same as those earlier models.
View 8 Replies
1998 Ranger. I have no vacuum to the heater control valve (see link below) and hoses are warm/hot to the firewall. Where to start troubleshooting?
More Information for FOUR SEASONS 74809
View 1 Replies
1992 Ranger 4x2 with 2.3L stick shift no AC no power steering. Recently the temp gauge began fluttering in the cold range from far left to just below the normal range. The defrost and heater blows only cold air. I had a professional shop radiator flush done. No change. I changed the engine thermostat out for a new one but no change. The upper radiator hose feels hot, so I assume the thermostat is working.
Questions: Where is the temp gauge sensor located on the engine? Is there another sensor or shutoff before the heater that might not be working? Where do I take things apart to check if the heater blend door is working?
View 1 Replies
I have a 2001 Mazda B3000. The a/c compressor is coming on while I'm running my heat. The air coming out while the heat is on stays warm. However, when I was running the A/C during the summer the air would start blowing out warm after it had been on for a while. Several people told me it may have something to do with the blend door or blend door actuator but both appear to be working fine. What it could be?
View 1 Replies
When I turn the control to heat the AC compressor kicks in. If turned to vent it does not kick in. Was this just a design flaw.
View 3 Replies
with a new heater core, new blower motor, and new resistor and no heat, what would be the problem? gonna check the thermostat tomorrow.
View 2 Replies
I have a 1997 Mazda b4000 new plugs wires head gasket an I cleaned out the radiator. My question is the truck runs good but my heat quit workin what could it be all fuse look good. Also there is water coming out of my tailpipe with white smoke. Should I be concerned.
View 2 Replies
I have a 2003 ford ranger xlt 4.0L and here recently my ac compressor has been making a loud click noise engaging even though i am not using heat or AC, so when it engages the rpms drop and almost wants to stall and it does this in about 10-15 sec. intervals, but when I am driving it acts fine. What is going on here, I recently had a vacuum leak and i found it and fixed it, and now this issue just started.
View 2 Replies
My 02 Mountaineer doesn't have any air flow volume out of the heat, defrost, or a/c vents. The temp will change from hot to cold and the air direction will also change from floor, dash, windshield, etc. The a/c recirculation door also seems to be working. The fan sounds as it is running very fast, just not putting out any volume. What should I look for?
View 3 Replies
My gf's dad said I could have his 07 Ranger 4.0 2wd with 230K on the clock if I fix the tranny 5R55E. One day he was driving home and all of a sudden had no drive. The tranny will run thru drive, neutral and reverse, but has no drive to it. Engine revs with nothing to show.
Tranny fluid was very dark and pan had nothing but the usual "metal flour" in it. I stopped there, did not pull the filter or anything else.
View 3 Replies
