1998 Ranger. I have no vacuum to the heater control valve (see link below) and hoses are warm/hot to the firewall. Where to start troubleshooting?
More Information for FOUR SEASONS 74809
Looking for a pic of where the 2 vacuum lines go off the IMCR on a 2002 ranger 2.3. Changed engines now not sure where these hoses go.
View 2 RepliesMy aforementioned ranger does not seem to heat up. Unless it is 95 degrees in the shade.... I have movement in the dash meter. Some - it will come off of the bottom - to not quite the c - then immediately dive back to less than cold ( which I realize is not possible) - engine seems to run fine. Use 93 octane or it knocks like a diesel. 135 K - I changed the thermostat. Less movement on gauge now than Before. Coolant level is fine. I read something in another post about the blend door. But my engine temperature doesn't even seem to be getting warm so how would the blend door be effecting that? I am an electrician not a mechanic, however I do all my own mechanic in in self defense. Since I cannot afford mechanics.
View 9 RepliesI have a 85 Ranger with a 2.3L engine. I'm not getting any heat. The temperature gauge never moves off of C, except when stuck in stop & go traffic. Even then it doesn't come up much. I tried to fix this last year by putting in a new thermostat, but it didn't work.
View 6 Replies1994 ranger 3.0 .. New: water pump, htr. hoses, radiator, thermostat, pulled & flushed htr. core. (2 year time frame) ....
View 5 RepliesMy son's 98 Expedition has no heat. The radiator and overflow tank are full, there's no air in the system. The radiator hoses get nice and hot but the heater hoses stay cold. We can hear the flow through the vents change when we change the temp control so I'm sure the blend door works fine. Seems like the problem is that no hot coolant is making it to the heater core. So I'm wondering if there is a diverter valve somewhere that could be bad that's keeping the hot coolant away from the HC or if a clogged HC is the only thing that could cause this.
View 1 RepliesThe air flow with ac and heat is low on my ford ranger. I can hear the blower change speeds, but on high, it barely comes out. The temp is fine and achanges from cold to hot like it should. i had the ac checked out by a shop that that does free checks - no problems with lines or compressor. I replaced the blower motor. The air changes from defrost to floor and all the positions fine, but the air flow out all the vents just isn't what it should be. It was working fine the first couple of days. I've read about the blend door motor, but I haven't read about people having this exact problem. I am almost to the point of bringing is to the dealer, but would rather fix it myself.
2007 Ford Ranger ... 6 cyl. 3.0 L ...
My 03 ranger with a 2.3 I4 does not want to restart when it is above about 80 deg outside and engine is warm. Will crank, but as soon as fuel in line runs out it stalls, like a vapor lock. After about 45 mins can push start normally( has manual trans) but have to wait about 2 hours to use starter to start.
View 11 Replies2002 Ranger XLT auto 3.0 will not start after it has run awhile, Was very intermittent at first sometimes six months would pass, sits for and hour or so and would start right up and run great. Lately it is becoming more frequent. Good fuel press, good spark, I have changed the coil pack, fuel relay, filter , am at a loss.
View 6 RepliesI have a 1994 Ford Ranger 4.0L 4x4, 130,000. I love this truck but about a year ago it started not starting after it warmed up short distances in the summertime? It start right up on cold crank...Runs smooth idles like a champ...but if i shut it off..wont start for 20 to 40 min??? It doesn't happen in the winter months??? So I changed the fuel pump, filter, relays. I feel like it has something to do with the Ignition Control Module. Would that come up in a code?
View 13 RepliesI have a 1994 Ford Ranger XLT xcab with a 4.0 engine.It will take off and drive in the freezing cold but when it warms up it will only go in reverse.Once in awhile it will go into drive.What seems to be the problem. I had also backed up over a railroad tie in an icy parking lot but still drove away.
View 3 RepliesOk I have a 97 f150 4.6L. My radiator has been bad for a while. With brown rust color. I replaced my radiator, thermostat, new upper and lower hoses. Everything runs great but I have no heat. I flushed everything including the heater core. Core is not leaking into cab, and both heater hoses are cold. FYI heat worked great until 5 days ago.
View 7 RepliesI've checked just about everything, coolant level is good, engine gets hot, heater control valves moves, blend air door moves, the heater hoses don't feel as hot as I think they should, but the gauge reads in the middle, I burped it thoroughly and still no heat , blower works i actually can switch the blend air door manually, but no change! what am i missing? t-stat was changed too. 2001 sport trac....
View 2 Replies98 ford Ranger 2.5L.
I have not heat from the vents, doesn't get warm at all. If I idle the enginer in 30 Degree weather it gets to almost the C.
Upper Radiator hose is hot, I have verified the thermostat is new and it opens at 192 degrees as it should. Replaced the Water Pump, Fan spins freely.
I have attempted to burp the system, it isn't kicking out anymore air from the lines that I can tell. I used a large funnel and filled it with Anti-freeze, it filled the radiator, burped the system and the reservoir filled to overflowing. All with the engine hot. (To be specific the funnel was always full of fluid so no air could get sucked backwards)
The heater core hose on the left when looking from the front of the vehicle does not get hot, the one on the right gets warm. I theorize that the heater core is clogged up somehow and that is why that left line doesn't get hot. There is no fluid in the cab of the truck from the core.
i have a 2001 ranger 4x4 the problem is sometimes it will switch into 4 wheel drive and sometimes it wont just hear clicking noise ,i'm preety sure it doenst have a vaccum.
View 14 RepliesI have a 2002 Ford Ranger 3.0L truck that, all of a sudden, has a problem with the HVAC system that blows air only thru the defrost vents even when selecting any other vent levels (defrost, face/middle or floor levels).
I did find a thread on another forum regarding this problem, only it was for the 95-01 Ranger model years, yet they say that the 2002 Ranger is not the same as those earlier models.
1992 Ranger 4x2 with 2.3L stick shift no AC no power steering. Recently the temp gauge began fluttering in the cold range from far left to just below the normal range. The defrost and heater blows only cold air. I had a professional shop radiator flush done. No change. I changed the engine thermostat out for a new one but no change. The upper radiator hose feels hot, so I assume the thermostat is working.
Questions: Where is the temp gauge sensor located on the engine? Is there another sensor or shutoff before the heater that might not be working? Where do I take things apart to check if the heater blend door is working?
I have a 2001 Mazda B3000. The a/c compressor is coming on while I'm running my heat. The air coming out while the heat is on stays warm. However, when I was running the A/C during the summer the air would start blowing out warm after it had been on for a while. Several people told me it may have something to do with the blend door or blend door actuator but both appear to be working fine. What it could be?
View 1 RepliesI have a 2005 ranger, 3.0 and automatic trans
The truck runs fine until it is warm... runs great down highway... stopping at a light or stop sign is horrible, It will act like the (old term ) carb is flooding out.
I put it on a meter It said tps so I replaced it. then it said number 4 cyl no power so I put new plugs in.... I do not hear any vacuum leaks, and It runs like a top when cold.
I have a 95 4.0 EFI inside of my 83 Ranger. Once the motor warms up, it starts to have an idle issue. I have to press the gas, in order for it not to cut off. Here is a video I posted a while back. A person suggested that it could be the MAF needed to be cleaned. I did that, and it did not work.
View 9 RepliesMy '04 Ranger has over 240k on the odometer. Runs great and has never given me any issues. Everything checks out OK - all the fluids, filters, and whatnot are in good shape. No CEL or any other indication that anything is wrong (except for maybe the IAC valve and clutch slave.)
I've noticed, though, that when I fire it up in the mornings to let it warm up while I scrape the ice and snow off the windows, the heat/defrost will not blow warm air. It doesn't matter how long I let it sit, it will only blow ambient air through the ducts.
When I get going down the road, however, the heat kicks in, after a bit, and works very well!
I've not found anything that would indicate an issue with the blend door or any other component and this is the first vehicle I've had that did this.
Is it normal for a 4.0 SOHC Ranger to do this? Or is there something I'm missing?... It's not really that big of a deal, but I do find it a bit odd that it would do this.
I mentioned the IAC above - I think it's "sticking" every once in a while and, when it does, I'll hear a loud "thump" right before it idles down to around 1k rpm. I can't see how this would affect the heat, though...