Ford Ranger / B-Series :: Higher RPMs Like Engine Is Missing - Loss Of Power
Apr 3, 2015
2002 ranger edge 3.0 5spd. Truck idles perfect, but when you get rolling and higer rpms feels like the engine is missing. loos of power and shakes. I replaced the usual, plugs and wire's, seemed to work for a bit but came back. I cannot get any info on the scanner and have checked all the fuses. I am thinking coil pack but don't understand why it idles perfect and only misses under acceleration. No check engine light on.
View 5 Replies
Advertisement
2002 ranger edge 3.0 5spd. Truck idles perfect, but when you get rolling and higher rpms feels like the engine is missing. loos of power and shakes. I replaced the usual, plugs and wire's, seemed to work for a bit but came back. I cannot get any info on the scanner and have checked all the fuses. I am thinking coil pack but don't understand why it idles perfect and only misses under acceleration. No check engine light on.
View 14 Replies
I have a 2012 F-250 6.7L w/8K miles. I have been struggling with this issue for 6 mo. The engine feels like its missing at low RPM. I would equate it to the feeling of a bad coil pack in a gas engine. The boost indicator drops to 0 for a split second then recovers. The dealer says they can't find the issue but went ahead and replaced the turbo. After the turbo replacement It got worse. This is an intermittent problem with no codes.
View 14 Replies
2001 M B3000 v6 my sons truck w 122k. He is overseas and I took it to deliver a CB750 bike to my brother in law... 4oo miles away from my place.
In the middle of nowhere TX it developed a bad miss or knock, almost a shudder in the 2 to 3 k rpm range. Idles ok just below 1k runs fine at 70 mph as long as the rpm is near or over 3k.
Not sure I want to turn around and drive back the 400 with it running like crap. I will take it to Autozone and pull codes tomorrow a.m. but what should I expect?
View 9 Replies
2000 Ranger 2wd 3.0 ... I bought my truck last summer for $1k from my neighbor, it has hit a deer so the grill is busted,front drivers fender bent up and bumper is bent all to heck. The old girl is rock solid reliable though and gets decent mileage with cruise heat and ac so I'm happy.
Anyways on to the point, I am having two big issues with it, the check engine light randomly comes on and causes it lose power sometimes at others you don't notice it. I have not been able to get codes read because it goes off every single time I go to someplace with a scanner. The light will usually go off if you floor it for a long stretch maf maybe?
The other issue is the transmission, I don't know for sure which tranny it is but the overdrive button does not work at all even though the fuses are good and when I drive down the highway second gear you have to let off for it to shift sometimes ( I've been leaning towards the valve body gasket for that) and lately it has started a horrible vibration kicking out of overdrive or just downshifting on hills etc.?
I forgot to mention it has 255k miles on it and I don't know the history besides the balljoint I replaced this week and radiator when I bought it.
View 3 Replies
I have a 03 F250SD with ~145,000 miles on the 5.4L. Just recently I have been having what seems to be a miss, or possibly a dead cylinder. I thought it might be a dirty MAF, but I cleaned it and have the same problem. The miss is more noticeable at the higher RPMs. I am checking the plugs today. So any solution? I refuse to take her to the shop and having another man up in her manifold.
View 8 Replies
I have a 96' ranger that has been missing quite regularly. The vehicle has over 200,000 miles on it, but has been taken care of regularly by me since 75,000.
Problem: When I start the vehicle, the engine takes a little bit to find the idle. It spits and fumbles around some until it finds a somewhat rough idle. Often, when I first start driving in the morning, the vehicle really jumps around due to misfiring. Even after running smoothly for awhile, the vehicle with sporadically misfire with no rhyme or reason. This is particularly true when climbing a grade. When sitting at a red light and idleing in gear, you can definitely feel the truck shaking from side to side. Also, when idling in gear, the battery gauge on the dash fluctuates, but when the vehicle is in park the battery gauge doesn't fluctuate...it just idles a little rough.
I had the Ranger to a garage and had them check the battery and alternator connections and ground to try and figure out what is making the battery gauge fluctuate...alternator and battery checked out...no diagnosis for fluctuation.
I replaced all plugs and wires and also checked the coil pack. One of the coils (#6) had some build-up in the top. I cleaned it out and replaced all the plug wires and everything snapped in place and fit fine.
The garage did tell me that an error code came up with the EGR valve and or sensor. They didn't seem to concerned about it. Do the EGR valve could be the cause of all the stuttering and misfiring going on with the ranger? I really don't know where else to look. Maybe replace the coil pack?
View 3 Replies
This has happened before on my 98 ranger 2.5. You can drive it 10,000 miles without any issue and then all of a sudden you take off and there's no power but it quickly returns. Within the last year I've changed fuel pump assembly, fuel filter, injectors, cool packs, and plugs. Is it mass air flow? It seemed to happen a lot more after I cleaned it. My scan tool is amateur but it has a maf reading in lbs. What should it be while driving? Fuel pressure is always between 65-72 when I check it within specs according to my book.
View 10 Replies
So I got everything fixed on my 94 ranger so I thought. Now it runs right on the "L" on the idiot gauge on 90 degree plus days running the AC. Also it seems to lose power at times and not even want to do 70. I think new coils, new plugs and wires may work. I also have an intermittent check engine light that pops up on occasion, but clears when you kill the motor and start it back up. I was really starting to like this truck despite it not being my style(I like square body rangers) and it being a 4 cylinder. I like the MPG but am starting to think the 200k engine may be fading
View 14 Replies
So, a couple of months ago, my Ranger lost a lot of power going down the road, and when I came to a stop it died, and wouldn't start. So I got it started by roll starting it, made it to a friend's, and then back home. I've put new spark plugs and wires in, and it needed it, badly, but it didn't work. I got a couple of codes off of it,
P0302- Cylinder 2 misfire detected(which I fixed with the spark plugs)
P1443 - which I can't find a definitive answer for
P0500- vehicle speed sensor malfunction
P0171- system to lean (bank 1)
So, the truck will turn over, and if I give it a lot of gas it'll start at stay started for a few minutes, but then cut off. When it is running it's running very very very roughly.
View 1 Replies
Bought my third 88 ranger today, drove it 55 of 60 miles home and it died. It lost power and acted like the coil was going bad. This one is a 2.9 5 speed 4x4. The a/c compressor is gone; but the 365 a/c works okay, or did.
My daughter was following me in her car; by the time we got back with my F150 and a chain, it started and ran until it was a half maile from home then lost power and died again.
Drug it home, put a new coil on and it started and revved up fine. Went to move it a couple of hours later and it will crank with the starter, but not fire.
I am getting 12 volts to the primary side of the coil, is there any way to check the TFI module without taking it off the distributor? (they are so accessable).
Or is there something else that I need to check? I really don't want to just throw money at it, I like to know for sure what is wrong before I buy parts.
View 1 Replies
Background- 2000 Ranger, 3.0L 2WD 170,000mi. This truck is not my daily driver, i try to drive it once a week.
I've never had this issue before... I drove all over town yesterday; multiple stops, no issue. Today i go to do the same thing and upon accelerating out of the driveway i lose all power for about 3 seconds. I get power back for about 3 seconds then lose it again. This continues for as longs as i'm driving. Also, no CEL. I go back to the house to look things over, can't find anything staring me in the face really.
Truck idles fine and the issue is not present when i run up the RPMs in park. I've been reading some other threads about similar issues and most replies begin with checking the regular maintenance stuff i.e. TB, MAF, IACV, pcv, etc. It seems like a complete loss of fuel or spark...but only when in gear with constant throttle???
View 14 Replies
My ranger sounds like it's revving up real high when I take off but don't have much power. Know what this could be?
View 5 Replies
1994 Ranger .. Last wednesday I had to get a jump because the lights where left on. Everything was normal on thursday. Friday morning. I went to go start the truck and notice that it would try once to start and then try a second time and it would start. Today I was driving it. The check engine light came on and when I get the RPMs up to shift up, I would loose all power and have to wait till it gets down below 10mph before I would get the power back.
View 8 Replies
My brother's 87 ford ranger 2.3L truck began to have problems. It would be running great, then start to misfire, run rough, sputter, shake and loose accelleration then die. Then it wouldn't start back up for a long time, sometimes til the next day. Little by little, the truck would drive a shorter and shorter distance between breakdowns. He first tried some minor work himself, (basic tune up) - replaced his rotor, cap, plugs, air filter, fuel filter, but that didn't fix it. He went to one garage (big mistake), who said the fuel pump pressure was fine but said he found a broken wire on the harness grounding out and it needed new ignition module and replaced it. (Cost was $350.00+), Garage promised to honor any additional work nec if it continued to have the same problem, and would be free of charge.
Five more breakdowns later and two more "better quality ignition modules", new battery terminals, and 1 new computer later, this joker did more unauthorized work and demanded another $200+ besides the fact of breaking his orig agreement "free of charge" if any further problems! Needless to say, second garage fixed the truck by replacing the magnetic pickup, part # DU 30-C (an electrical part that goes in the distributor and pulsates a current to operate the timing) (it does something like that) and the truck has been driven approximately 40-60 miles as of today, (3 days later), without breaking down. All the other times when picked up from incompetent garage, it wouldn't go more than 1 - 7 miles before breaking down and each time they didn't fix it.
View 4 Replies
I recently picked up a 93 ranger sport 4x4 with 2.3L engine and 5spd.. Has run fine for the first 2 weeks of ownership but yesterday morning, it started cutting out on the highway. When I say cutting it is like all loss of power for a brief instant and then it right back without even losing any speed, I could watch tach drop from 2500 to 2k and then right back to 2500 again..
Did it sporadically all the way home about 10 miles sometimes once in a mile other times 6-7 times in a mile. Truck has 126k on it, and within last 26k miles PO replaced timing belt, coil packs, plugs, wires, ICM, and just before i picked it up from him a new EGR and fuel filter.
No check engine light
Fast forward to this AM
Wouldn't start at all, i can hear fuel pump spinning and she cranks and cranks but no start up.... played with multiple things including the ICM but found 2 of 3 heads rounded off so i cant remove it until i can get it in to my garage and dremel those suckers off..
Went and bought a replacement ICM figured i could plug it in run a ground from the bottom left hand bolt hole so i could get it fired up and in to my garage.. plugged the new one in grounded it and it still wouldn't start...
So I decided to replug the original ICM back in and grab my spark plug tester, remove number 3 plug wire on passengers side insert the tester and have my wife crank it over and wonder of wonder it fires up...
shut it down remove the tester and have her start it up again and it fires right back up so i let it warm up for 15 minutes.. grab my autoxray.. shut it down hook up the scan tool and run the KOEO scan.. gives me a passed 111 code... OK lets start it back up and run the KOER test.. wont start back up.. reinstall the spark plug tester to #3 wire and NOW it has no spark..
View 6 Replies
Ok I've been plagued with this very random misfire/power loss/hesitation problem going on a couple of months. You could drive the truck anywhere from 50-300 miles without having an encounter of this problem. It seems to do it now mostly on contiguous long trips over like 30 miles. It one time threw up a P1131 code which quickly went away on it's own. This is a list of stuff that has been recently changed: plugs, wires, coil packs, air filter, pcv valve, fuel injectors, tps, idle air valve, MAF cleaned, fuel filter, and egr valve.
I sprayed with brake cleaner for vacuum leaks around the intake tonight after driving a continuous 50 mile round trip it messed a few times on the way back. When I sprayed the EGR valve mounting area it idled rough when it was hit with brake clean and idled up. So there's a leak there. Or is it stuck? It will be driving normal and usually when you come to a stop the engine will start missing really bad and then when you take off there's no power at all. You keep your foot on the gas and eventually it will feel like all the power is just turned on.
If it does it while you're driving highway speeds it will feel like you've lost a cylinder but it's not as dramatic as when you come to a stop and it starts missing. I can't be 100% but I don't think the EGR wasn't leaking before I replaced it and it was still doing the same thing. I'm wondering why the Check Engine Light won't pick up an obvious misfire when you can you actually feel it. And why if it was the vacuum leak would it only start doing it after many miles of driving?
View 11 Replies
Two days ago, I was driving on a North GA steep, windy, mountain road in my 2002 v6 4.0 Ranger. All of a sudden, i started revving real high (about 4000rpms) and getting no power (20mph). I pulled over immediately and transmission fluid was pouring, by the quart, out of my truck. I didnt get to look exactly where it was coming from, since i backed away once i saw a small flame coming from the leak. i then called a tow truck (assuming it was a seal or a hose break) and had it towed to my house.
I started investigating the possible problems and didn't really see anything noticeable under the truck (not that I was expecting to). So what I did was put three quarts of transmission fluid in the dipstick hole and put in gear to see if I could spot a leak. nothing. then I drove it around the block to get it warmed up and put a little pressure on the transmission by driving up a semi-steep hill to see if that would spark the leak again. still no sign of the a leak.
And finally, when I went to go check the dipstick after my test drive, it read to be above the cross hatched area, hence being overfull. What my next step should be?
View 6 Replies
I am looking over a 1998 Ford Ranger. Very low miles for its age (67,000) and kept in very good shape. When I took it for a drive, I noted an issue.
- there's a whining sound in first gear and reverse that varies according to the engine RPMs. I thought it might be the power steering pump, as that whined when I turned the wheel.
However, the noise went away when I shifted to the higher gears. Been a while since I drove a stick - my Bug back in 2003, IIRC.
What I might be getting into? I really like this machine, aside from that issue, and I would like to nail the problem down ASAP...
View 1 Replies
I have a 98 Ranger with a 3.0 (5 speed) that has 254,000 miles on it. I drove it to town this morning (8 miles) and it ran normally. I stopped for just a few minutes at a house and when I re-started the truck, it was missing very bad and the CEL came on. It wouldn't haul itself in anything higher than 3rd gear. I decided to try to make it back home. I drove it less than two miles and it cleared up and started running perfect again. I came home anyway and read the code with my scan tool.
It said that I had a miss fire on cylinder #5. I erased the codes and shut the CEL out and its been running perfectly ever since. (I have put about 150 miles on it so far) If it does it again, I will start by replacing the plug wires. I have already done that but its been a long time ago. The plugs have been replaced twice as well. I was wondering if it could be something other than electrical like a dirty injector or maybe the compression rings lined up and it momentarily lost compression.
View 14 Replies
I have a 2001 ranger 2wd with a 2.3. It has a miss when acceleration. There is no check engine light. I have changed: fuel filter. Plugs, wires, crank position. Sensor, cleaned mass air flow sensor. Ran 2 bottles of injector cleaner in it. Still missing???? It runs and idles great. Just has a miss in the lower RPM's 1000-2000 then goes away. I really don't wanna take it to a shop. What do you all think??
View 11 Replies
