This is something to check, I found the vent line pinched closed on my 2000 F350 when I was trying to find out why it was leaking. When I was under my 2013 installing the hitch I checked it and found the same problem. The clip doesn't pinch it closed right away but it will happen if you don't move the clip.
View 8 Repliesso while replacing the rear brake lines in my 2001 F-250. / 5.4, the flex line that drops from the frame bolts to the axle through the axle breather threaded vent line. The friggin thing crumbled on me and now I can't find a replacement for it. Where I can get it or what it's actual name / part number is so I can call the Ford dealer and hope it's not obsoleted?
View 3 RepliesSo my 2000 f350 is leaking transmission fluid from the cooler line. It goes to the rear of the transmission, but where does it go to from there?
View 5 RepliesI have a 2000 f250 V10 CC 4x4 long bed. The rubber fuel line that has a quick disconnect to attach to the fuel filter along frame is leaking. This is on the filter side going to engine. Ford tells me fuel line not available. Dorman products tech assist can't tell me which connector of there's will fit my truck.
View 2 RepliesI have heard that the front brakes are separate, and if the rear brakes have a leak and the line is empty, the fronts should still work. Is this likely to be true? If I drive the truck will I be able to stop with the fronts alone (assuming they will still work?)
I plan to drop the truck off late tonight when there is likely to be no traffic, but thought I would ask.
My transmission cooling line is leaking. It leaks where it connects to the radiator. Im not sure how I go about removing the connection from the radiator. It is tough to tell from the rust on the connection weather or not I can use a wrench on it. I have read here that there are cooling lines in this part of the radiator for the transmission. Is it serviceable or do I need a new radiator. I dont want to touch it until I know what I'm looking at.
05 F250 5.4L 4x4
[URL]......
So this is my major problem, leaving for a camping trip tomorrow afternoon. It's just 15 miles away, easy flat drive. What has happened is the trans line coming out of the bottom of radiator is leaking next to the fitting about an 1/8 ' out, So I can't cut off and splice in hose for the trip. I worked on it for about an hour, rusted on, tried some heat and now have some PB Blast on it and all I am doing is starting to round off the head of fitting. Is there any way to bypass this just to get the camper to campground and then get to a shop while we are gone Don't care if I have to splice and cut, will get new lines later.
2004 f250SD 5.4 83000miles
I replaced a rear rusted brake line a couple of years ago. It rusted where the line met the bracket. I'd never done this before but bought a flare (flaring?) tool and fixed it.
This week the longer line that runs down the length of the truck started leaking. It looks like the line was once held in place by a small bracket just in front of the rear wheel but it wasn't in that bracket anymore. I guess it rubbed against the metal and water/sand rusted it out.
A local garage said they'd need to drop the fuel tank and estimated that it would be several hours (and hundreds of dollars) to do the job. It looks like I might be able to cut the old one out and then fish the new line up through there and replace it.
Also, what is the diameter of the line? It is a 2004 F350. I can certainly cut it out first and then take a piece of it to the local auto parts place to get the replacement line.
I have a 2000 f250 4x4 7.3 diesel. I had problems with my a/c and controls for sometime now. my a/c was blowing threw the defrost vent. I was told my blend door was bad. I bought a new blend door installed it,still doing the same thing. I was told to check my vacuum lines. I check them, they were bad. I replace my vacuum lines and my vac pump as well. that fixed my problem blowing threw the defrost vent. I can control my air flow from floor,dash vents and defrost vent. the problem I have, I not able to control my temperature when I turn my center from red to blue. It blows hot air and the air that is coming out of the vents isn't very strong at all.
View 1 RepliesOn my '97 F250 the rear brake line going to the rear right wheel has a rusted hole. It measures 50" total. Instead of bending a new metal line. I see they have a "poly armor" line that can be bent by hand( no tools needed). I see Autozone has them.
View 14 RepliesI have a 2000 dually and the brake line that runs the frame rail finally rusted through. It runs on the same side as the fuel tank. Is it easier to leave the old one in and run a new one along side it? I sure hate to think that I'll have to drop the tank for this.
View 7 RepliesI purchased a 2000 F250 7.3 4x4 (auto transmission) about 8 months ago. I've noticed recently that when I accelerate there is a slight hesitation like there is slack in the drive line. This does not happen when the truck is moving and I accelerate. There is not audible clunk and the hesitation is not in the motor.
I checked the u-joints and they all feel tight. There is a little slack in transfer case that allows me to turn the drive line slightly back and forth. Is this normal? Should I be planning on a transmission or transfer case rebuild soon?
Update: I was researching the leaf spring isolator pads (mine are warn out or missing) and it sounds like these can cause something similar to what I am experiencing. I am planning on pulling a 28' travel trailer from Colorado to Wisconsin next month and would like to avoid any issues if possible...... Obviously, I know ....
I made a bone head mistake and crunched the steel brake line between the rear axle and the passenger side sway bar mount. Truck is a 2003 F-250 with a 7.3. I would like to go to the auto parts store, get bulk steel brake line and bend it myself. But, I don't know what size the line is or what size the fittings are. Whatare the sizes???
View 3 RepliesHave a 2007 V10 and I want to put in a Magnafine tranny filter. Instructions say to plumb it in to the return line. Which one is this, top or bottom?
View 11 RepliesThe rear differential is leaking on my 2000 f350, i am going to replace the gasket. When I take the cover off will all the gears pop out or are they held in? Also how much differential fluid does it take?
View 8 RepliesMy rear end cover has been leaking and I don't have time to fix it right now. I was going to check the oil and maybe add some if needed but I cant find anywhere to ad oil or check it? Am I missing something? The add plug is the one Id like to find.
View 2 RepliesIf you look at the top of the picture you can see the two bolts with fresh oil on them.
I have a 2002 Ford F250 V10 Pick up. I noticed oil leaking from under the oil pan. I wiped off the pan and bolts to see where it was coming from. The oil seems to be leaking from the rear of pan. There's always fresh oil on the rear bolts that hold the pan and I also noticed oil coming from one of the two hoses that go from the radiator to where the oil filter mounts.
But don't those hoses carry radiator fluid and not oil? I bought this truck in July and no oil leaking from underneath. It seemed to have started after I did my first oil change on it. I used regular Vavoline 5W-20 and motorcraft oil filter.
My grandfathers 99 F350, started suddenly, do not know if it was while sitting or while driving. Its more of a stream than anything else. Coming from the rear, cannot see where, appears to be toward the vee of the engine, not inside the bellhousing. The firewall insulation is damp from coolant. Doesnt start until engine starts warming up.
Is there something commonly replaced back there? Didnt want to yank the intake in 20* weather for exploratory surgery. Is not the heater hoses. Idk if the EGRs are cooled on these, thats about my only idea other than freeze plug, coolant tests good down to -20ish, hasnt been below zero in weeks (prior to leak). Not familiar with any of the modular engines.
I just bought a 2000 F250 SD 6.8 v10 and its mixing coolant in the block and leaking oil. I'm debating on just dropping a newer v10 in it but im just not 100% sure that this engine is shot. It runs great when there's oil in it and I can't even tell there's any problems going on for well over a couple hours after i fill it up with oil.
View 8 RepliesThe rear hub outer oil seal on my 05 350 is leaking. The 350 Super Duty Twin Cab was never imported into the UAE so can I use the same seals as the Excursion or another Ford vehicle?
Failing that do we know the name and part number of a seal manufacturer whom I might be able to source from in Dubai? Ford don't make the seals them selves so there must be an alternate source for these things surely?
Changing out the rear main oil seal on my 1999 F250 Super Duty. I have a 7.3L diesel with 6 spd manual trans. with 98K miles. This past week it has developed a very slow engine oil drip where the engine meets the transfer case. Is it necessary to remove the engine or just the transmission? What does a transmission/transfer case combo weigh? What special tools would I need?
View 1 Replies